ECO mode VOLVO XC90 2014 Owner´s Manual

03 Climate
Electronic climate control (ECC)
03
}}
99
contaminated outside air, the air intake closes and the air inside the passenger compart-ment is recirculated, i.e. no outside air entersthe vehicle. The filter also cleans recirculatedpassenger compartment air. When the ECC system is in the
AUTO mode,
the green LED will be on.
Recirculation
Press this switch to engage the recirculation function (air in the passenger compartmentrecirculates – no fresh air enters the compart-ment). The LED in the switch will light up toindicate that the function is engaged. • Use this function if the outside air is con- taminated with exhaust gases, smoke,etc or to heat/cool the vehicle quickly.
• Recirculation should not be used for morethan 15 minutes. If your windows begin tofog or mist, make sure that the recircula-tion function is switched off.
• Selecting
Defroster automatically
switches recirculation off.
• Timer mode activation: (Vehicles equip-ped with the Interior Air Quality systemhave no timer mode) Press and hold therecirculation button for at least 3 secondsto activate a recirculation timer mode.The amber LED in the recirculation buttonwill flash 5 times to show that the timermode is being activated. In timer mode, each time the recirculation button ispressed, the climate control system willrecirculate the air in the passenger com-partment for 5 – 12 minutes, dependingon the outside air temperature, and thenrevert back to fresh air.
• Timer mode deactivation: Press and holdthe recirculation button for 3 seconds.The amber LED in the recirculation buttonwill illuminate steadily for 5 seconds toshow a return to "normal" mode.
• In normal mode, when the recirculationbutton is pressed, the climate controlsystem will recirculate the air in the pas-senger compartment until the recircula-tion button is pressed again.
• Timer mode memory: If the vehicle isturned off while timer mode is active,timer mode will still be active when thevehicle is restarted.
AUTO
This function automatically regulates the Electronic Climate Control system so that theselected temperatures are maintained. Theblower, heating, air distribution (air flow), airconditioning, and optional air quality sensorare controlled. If you prefer to manually setany of these functions, the remaining func-tions will still be controlled automatically.Pressing the
AUTO button overrides any set-
tings that were previously made manually.
Air distribution
G027267
• Air flow to windows
• Air through panel vents
• Air through floor vents
Press AUTO to automatically regulate air flow
or press any combination of the controls shown in the illustration to manually adjust airflow. An LED in the switch will light up if an airflow control has been pressed.
Passenger compartment
temperature sensor
Measures the temperature in the compart- ment.
Defroster
This function defrosts/deices the windshield and front side windows. The LED in the

04 Interior
Rear seats
04
108
Entering the third row of seats
G027027
Tilting the outboard backrests in the second row of seats:
•Pull up the handle (1), hold it up, and tilt the backrest forward to move the seat.
• Return the backrest to the upright posi-tion to slide the seat back to its originalposition.
Forward/rearward seat adjustmentLift the adjustment bar (2) to move the seat forward or rearward.
Removing the center console 1
G028445
In order to make it possible to move the cen- ter seat in the second row of seats as far for-ward as possible (seven-seat models only),the rear section of the center console can beremoved. •
Pull the handle (see illustration) and lift out the console.
• To return the console to its original posi-tion, slide it back into position until itclicks into place.
G027033
Sliding center seat – second row (seven-seat models only)
The center seat in the second row can be moved farther forward than the outboardseats. This makes it possible for a childseated in this position to sit closer to the peo-ple in the front seats.
1
The center console cannot be removed on vehicles equipped with the optional Rear Seat Entertainment System.

04 Interior
Rear seats
04
109
G027015
Head restraint – second row, center position
The head restraint in the center position can be adjusted to 4 different heights. To raise – pull the restraint up until it clicks
into one of the four heights positions.To lower – press the button at the base of
the support (see illustration) and press the head restraint down carefully.
WARNING
The center rear seat head restraint should only be in its lowest position when thisseat is NOT occupied. When the centerposition is occupied, the head restraintshould be correctly adjusted to the pas-senger’s height. The upper edge of thehead restraint should be at least on a levelwith the upper-most point of the seatoccupant's ear.G027022
Folding the backrests – second row of seats
CAUTION
To help avoid damage to the upholstery, there should be no objects on the rear seatand the seat belt should not be buckledwhen the backrest is folded down.
1. Move the seat(s) to their rearmost posi- tion (seven-seat models only).
2. Pull the loop to fold down an outboard head restraint. Press down the center head restraint if necessary (seepage 109).

04 Interior
Securing cargo
04
121
Steel grid (accessory)
Installing the grid, upper attachments1. Lift in the grid through the tailgate orthrough one of the rear passenger doors (in this case, fold down the rear seatbackrests/backrests in second row ofseats in seven-seat models).
2. Insert one of the grid's upper attach- ments into an attachment bracket aboveone of the rear passenger doors (seeillustration above).
3. Push the grid's attachment into the for- ward position in the attachment bracket(see inset illustration above) to lock theattachment in place.
G027057
Lower attachments
4. Insert the grid's other upper attachment in the attachment bracket above the opposite rear passenger door, and pressthe attachment into the forward positionin the attachment bracket to lock it inplace.
Installing the grid, lower attachments1. Insert the lower attachment bracketthrough the steel grid's lower mount from underneath.
2. Install the spring on the attachment bracket and tighten the knob. 3. Secure the attachment bracket hook in
the lower cargo eyelet. Turn the knob totension the attachment bracket in thecargo eyelet.
4. Repeat the operation on the opposite side.
5. Tighten both attachment brackets alter- natively.
6. Place the protective caps on the threads above the knobs.
WARNING
•The backrests of the third row seats must be folded down when installingthe steel grid.
• The steel grid is installed behind thesecond row of seats. To avoid the riskof injury, no one should be allowed tosit in the third row of seats when thesteel grid is in place in the vehicle.

05 Locks and alarm
Remote keys and key blades
05
128
press the button again (within 10 seconds) to unlock all doors, and the tailgate.
Tailgate unlock
Press this button to unlock the tailgate (with- out unlocking the other doors). This functionwill not open the tailgate.
Panic function
For more information on this function, see page 133.
Approach lighting
Press this button when approaching the vehi- cle at night to light up the interior courtesylight, parking lights, license plate lights andthe lights in the door mirrors.
Lock
Press once to lock all doors, and the tailgate.
Fold key blade in/out
Press to extend the key blade. This button must also be pressed when the key blade isfolded back into the slot in the side of theremote key unit.
NOTE
• If an airbag deploys, your vehicle's SRS control module will attempt toautomatically unlock all doors.
• The key blade may also be used tolock and unlock the doors, and to acti-vate and deactivate the alarm system.
• To avoid leaving your keys in the vehi-cle, make a habit of always locking thevehicle with the remote key.
• If the key blade section of the remoteis not fully folded out when starting thevehicle, the immobilizer function maymake it impossible to start the engine.
• The vehicle can be locked even if adoor is open. When the door(s) areclosed, they will be locked. Please beaware that the keys could be locked inthe car when this is done.
Automatic re-lockingIf the doors are unlocked, the locks will auto- matically reengage (re-lock) and the alarm willrearm after 2 minutes unless a door or thetailgate has been opened. This helps preventthe car from inadvertently being left unlocked. FCC ID: LQNP2T-APU This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not causeharmful interference, and (2) this device mustaccept any interference received, includinginterference that may cause undesired opera-tion. Canadian 2306104388 Model 504 2927 by Donnelly Operation is subject to the following condi- tions: (1) this device may not cause interfer-ence, and (2) this device must accept anyinterference, including interference that maycause undesired operation of the device. Canadian 2306104388A Model 509 977 by Connaught Electronics Operation is subject to the following condi- tions: (1) this device may not cause interfer-ence, and (2) this device must accept anyinterference, including interference that maycause undesired operation of the device.

06 Starting and driving
Economical driving
06
146
Economical driving conserves natural resources
Better driving economy may be obtained by thinking ahead, avoiding rapid starts andstops and adjusting the speed of your vehicleto immediate traffic conditions. Observe thefollowing rules:
• Bring the engine to normal operating tem- perature as soon as possible by drivingwith a light foot on the accelerator pedalfor the first few minutes of operation. Acold engine uses more fuel and is subjectto increased wear.
• Whenever possible, avoid using the vehi-cle for driving short distances. This doesnot allow the engine to reach normaloperating temperature.
• Drive carefully and avoid rapid accelera-tion and hard braking.
• Use the transmission's
D (Drive) position
as often as possible and avoid using"kickdown" to help improve fuel econ-omy.
• Do not exceed posted speed limits.
• Avoid carrying unnecessary items (extraload) in the vehicle.
• Maintain correct tire pressure. Check tirepressure regularly (when tires are cold).
• Remove snow tires when threat of snowor ice has ended. •
Note that roof racks, ski racks, etc,increase air resistance and also fuel con-sumption.
• At highway driving speeds, fuel consump-tion will be lower with the air conditioningon and the windows closed than with theair conditioning off and the windowsopen.
• Using the onboard trip computer's fuelconsumption modes can help you learnhow to drive more economically.
Other factors that decrease gas mileage are: • Dirty air cleaner
• Dirty engine oil and clogged oil filter
• Dragging brakes
• Incorrect front end alignment.
Some of the above mentioned items and oth- ers are checked at the standard MaintenanceService intervals.
CAUTION
Drive slowly and carefully if going through standing water (i.e. flooded roadways,etc.). Damage to the engine could result ifexcess water is drawn in through the airintake system. Never drive the vehicle inwater deeper than 18 inches (48 cm).

06 Starting and driving
Automatic transmission
06
151
starts off in 3rd gear to help maintain traction. First and second gears will only be used dur-ing kickdown.
NOTE
Mode
W can be chosen regardless of the
postion of the gear selector but will only function when the gear selector is in the D
(drive) position.

06 Starting and driving
All Wheel Drive*
06
* Option/accessory, for more information, see Introduction.153
All Wheel Drive (AWD) – general information
Your Volvo can be equipped with an electron- ically controlled All Wheel Drive system*,which means that power is distributed auto-matically between the front and rear wheels.Under normal driving conditions, most of theengine's power is directed to the frontwheels. However, if there is any tendency forthe front wheels to spin, an electronicallycontrolled coupling distributes power to thewheels that have the best traction.
Tire dimensionsVolvo recommends that you always drive ontires of the same brand, size, construction(radial), tread pattern, load-, speed-, traction-,temperature-, and treadwear rating. Neverdrive on mixed tires, except for brief periodswhen the temporary spare tire is in use. Always use properly inflated tires of correct dimensions. Tire size and inflation pressuresare shown on the tire inflation pressure plac-ards, located on the driver's side B-pillar (thestructural member at the side of the vehicle,at the rear of the driver's door opening), or onthe inside of the fuel filler door on Canadianmodels.
Temporary SpareThe temporary spare tire is for temporary,low-speed, short-distance use only. Replaceit with a full-sized tire as soon as possible. Donot drive on the temporary spare at speedsabove 50 m.p.h. (80 km/h).
NOTE
Never install snow chains on a temporary spare.

06 Starting and driving
Towing a trailer
06
165
Points to keep in mind when towing a trailer
•When towing trailers
without brakes, the
maximum permissible trailer weight is 1,700 lbs (750 kg).
• If necessary, redistribute the weight ofany cargo in the trailer to avoid excessiveweight on the trailer hitch.
• The maximum trailer weight listed in thetable for All Wheel Drive models,5,000 lbs (2250 kg) is only applicablewhen there are not more than two occu-pants in the vehicle, in the front seats,with a combined weight of 300 lbs(135 kg), with no other cargo in the vehi-cle.
• The maximum weight listed for FrontWheel Drive models, 4,000 lbs (1800 kg)is only applicable when there are notmore than four occupants in the vehicle,in the front seats and second row ofseats, with a combined weight of 600 lbs(270 kg), with no other cargo in the vehi-cle.
• Vehicles used for towing a trailer on aregular basis, or for long-distance high-way towing should be equipped with anautomatic transmission oil cooler andVolvo's automatic self-leveling system forthe rear suspension. Consult your Volvoretailer. •
Volvo recommends the use of Volvotrailer hitches that are specially designedfor the vehicle.
• All Volvo models are equipped withenergy-absorbing shock-mounted bump-ers. Trailer hitch installation should notinterfere with the proper operation of thisbumper system.
• Increase tire pressure to recommendedfull inflation pressure. See chapter"Wheels and tires."
• When your vehicle is new, avoid towingheavy trailers during the first 620 miles(1,000 km).
• Engine and transmission are subject toincreased loads. Therefore, engine cool-ant temperature should be closelywatched when driving in hot climates orhilly terrain. Use a lower gear and turn offthe air conditioner if the temperaturegauge needle enters the red range.
• If the automatic transmission begins tooverheat, a message will be displayed inthe text window.
• Hauling a trailer affects handling, durabil-ity, and economy.
• It is necessary to balance trailer brakeswith the towing vehicle brakes to providea safe stop (check and observe state/local regulations). •
Do not connect the trailer's brake systemdirectly to the vehicle's brake system.
• Remove the ball and drawbar assemblywhen the hitch is not being used.
• Volvo recommends the use of syntheticengine oil when towing a trailer over longdistances or in mountainous areas.
NOTE
•When parking the vehicle with a trailer on a hill, apply the parking brakebefore putting the gear selector in
P.
When starting on a hill, put the gearselector in D before releasing the park-
ing brake. Always follow the trailermanufacturer's recommendations forwheel chocking.
• If you use the manual (Geartronic) shiftpositions while towing a trailer, makesure the gear you select does not puttoo much strain on the engine (usingtoo high a gear).

06 Starting and driving
Cold weather precautions
06
169
If you wish to check your vehicle before the approach of cold weather, the followingadvice is worth noting:
• Make sure that the engine coolant con- tains 50 percent antifreeze. Any othermixture will reduce freeze protection. Thisgives protection against freezing down to–31 °F (–35 °C). See section "Coolant".
• The use of "recycled" antifreeze is notapproved by Volvo. Different types ofantifreeze must not be mixed.
• Volvo recommends using only genuineVolvo antifreeze in your vehicle's radiator.Your Volvo retailer stocks plenty of Volvoengine coolant to protect your vehicleduring cold weather.
• Try to keep the
fuel tank well filled – this
prevents the formation of condensation inthe tank. In addition, in extremely coldweather conditions it is worthwhile to addfuel line de-icer before refueling.
• The viscosity of the engine oil is impor-tant. Oil with low viscosity (thinner oil)improves cold-weather starting as well asdecreasing fuel consumption while theengine is warming up. Full synthetic0W-30 oil is recommended for driving inareas with sustained low temperatures.
• The load placed on the
battery is greater
during the winter since the windshieldwipers, lighting, etc. are used more often. Moreover, the capacity of the batterydecreases as the temperature drops. Invery cold weather, a poorly charged bat-tery can freeze and be damaged. It istherefore advisable to check the state ofcharge more frequently and spray an anti-rust oil on the battery posts.
• Volvo recommends the use of
snow tires
on all four wheels for winter driving – seesection "Wheels and tires."
• To prevent the
washer fluid reservoir
from freezing, add washer solvents con-taining antifreeze (see page 224 for thelocation of the washer fluid reservoir).This is important since dirt is oftensplashed on the windshield during winterdriving, requiring the frequent use of thewashers and wipers. Volvo Washer Sol-vent should be diluted as follows:
• Down to 14 ° F (–10 ° C):
1 part washer
solvent and 4 parts water
• Down to 5 ° F (–15 ° C):
1 part washer
solvent and 3 parts water
• Down to 0 ° F (–18 ° C):
1 part washer
solvent and 2 parts water
• Down to –18 ° F (–28 ° C):
1 part washer
solvent and 1 part water
• Use Volvo Teflon Lock Spray in the locks.
NOTE
Avoid the use of de-icing sprays as they can cause damage to the locks.
W – Winter/Wet driving mode – enhanced vehicle traction
•Mode W will only function if the gear selector is in the (
D)rive position.
• Press the button at the base of the gearselector to engage/disengage this drivingmode.
• An LED in the button will light up to indi-cate that W is engaged and this will alsobe displayed in the instrument panel (seepage 58).
• This mode may be selected for starting/moving off on slippery roads.