check engine YAMAHA GP1300R 2007 Owner's Manual

Operation
58
EJU33370
Post-operation care
WARNING
EWJ00680
Do not start the engine on land if anyone is
behind the watercraft. Hot water and
steam spurting from the exhaust outlet
into the air can cause serious burns.
To keep your watercraft in top shape, always
take it out of the water after using it and per-
form the following procedures. Leaving the
watercraft in the water for extended periods
will accelerate the rate of normal deterioration
of the jet unit components and hull finish. Ma-
rine organisms and corrosion are some of the
conditions that can adversely affect the life of
many watercraft components.
(1) Remove the watercraft from the water.
(2) Wash down the hull, handlebars, and jet
unit with fresh water.
(3) Remove the seat and check the engine
compartment for water. To drain excess
water, remove the stern drain plugs, and
then raise the bow of the watercraft
enough to allow the water in the bilge to
drain out.
NOTE:
This watercraft is equipped with a jet vacuum
bilge draining system and an electric bilge
draining system that remove water from the
engine compartment while you are underway.However, some residual water will remain.
(See page 39 for bilge draining procedures.)
(4) Place the watercraft in a horizontal posi-
tion.
(5) Flush the cooling system to prevent it
from clogging with salt, sand, or dirt. (See
page 60 for flushing procedures.)
(6) Drain residual water from the exhaust
system by running the engine at 4000
r/min for 10 to 15 seconds.
CAUTION:
ECJ00600
Do not run the engine over 4000 r/min on
land, otherwise the catalytic converter
could be seriously damaged.
(7) If the watercraft will be stored for a week
or more, lubricate internal engine compo-
nents to help prevent corrosion. (See
page 61 for lubrication procedures.)
(8) Rinse the engine and engine compart-
ment with a small amount of water.
CAUTION:
ECJ00570
Do not use high-pressure water when rins-
ing the engine or engine compartment as
severe engine damage could result.
(9) Wipe the engine and engine compart-
ment dry with a clean cloth (repeat step 3,
if necessary).
(10) Wipe the hull, handlebars, and jet unit dry
with a clean cloth.
(11) Spray a rust inhibitor on metallic parts to
minimize corrosion.
WARNING
EWJ00690
Do not spray flammable rust inhibitor
products on engine surfaces while the en-
gine is hot. The sprayed substance or pro-
pellants could catch fire.
UF1G74E0.book Page 58 Monday, July 31, 2006 10:10 AM

Maintenance and care
62
(2) Clean the battery casing using fresh wa-
ter.
(3) If the battery terminals are dirty or corrod-
ed, clean them with a wire brush.
(4) Fully charge the battery.
(5) Apply Yamaha Marine Grease or
Yamaha Grease A to the battery termi-
nals, and then store the battery in a cool,
dry place.
(6) Check the battery at least once every 2
months and fully charge it if necessary.
CAUTION:
ECJ00100
Always keep the battery charged. Storing
a discharged battery can cause permanent
battery damage.
To check the condition of the battery, check
the specific gravity of the electrolyte or mea-
sure the voltage at both battery terminals.
Charge the battery if the voltage is less than
12 volts.
It is recommended to have a Yamaha dealer
check the specific gravity and charge the bat-
tery. If you maintain the battery yourself, be
sure to read and follow the instructions provid-
ed with the battery tester and charger you
use.
EJU33720Cleaning the watercraft
Clean the watercraft before storing it for a long
period.
WARNING
EWJ00260
Do not spray flammable rust inhibitor
products on engine surfaces while the en-
gine is hot. The sprayed substance or pro-
pellants could catch fire.
(1) Wash down the hull, handlebars, and jet
unit with fresh water.
(2) Rinse the engine and bilge area with
fresh water. Drain all of the water and
wipe up any remaining moisture with
clean, dry rags.
CAUTION:
ECJ00110
Do not use high-pressure water when rins-
ing the engine and bilge area as severe en-
gine damage could result.
(3) Spray the engine’s exterior with a rust in-
hibitor and lubricant.
(4) Wax the hull with a non-abrasive wax.
(5) Wipe all vinyl and rubber components,
such as the seat and engine compart-
ment seals, with a vinyl protectant.
Specific gravity (for reference):
1.28 at 20 °C (68 °F)
UF1G74E0.book Page 62 Monday, July 31, 2006 10:10 AM

Maintenance and care
65
EJU33820Periodic maintenance chart
The following chart gives general guidelines for periodic maintenance. However, maintenance
may need to be performed more frequently depending on your operating conditions.
This “” mark indicates maintenance that you may do yourself.
This “” mark indicates work to be done by a Yamaha dealer.
* This operation should be performed after every use.
Item OperationInitial Thereafter every
Page 10
hours50
hours100
hours100
hours200
hours
6
months12
months12
months24
months
Spark plugsCheck, clean, adjust 67
Lubrication pointsLubricate 68
Intermediate hous-
ingLubricate 68
Fuel systemCheck 66
Fuel tankCheck, clean 66
Oil injection sys-
temCheck, clean 66
Throttle shaftCheck—
Cooling water pas-
sagesFlush
*60
Water inlet strain-
erCheck, clean—
Bilge strainerClean—
Electric bilge
pump strainerCheck, clean—
ImpellerCheck—
Jet thrust nozzle
angleCheck, adjust 66
QSTS mechanismCheck, adjust—
Throttle cableCheck, adjust 67
Stern drain plugsCheck, replace 40
BatteryCheck, charge 69
Rubber couplingCheck—
Engine mountCheck—
Nuts and boltsCheck—
UF1G74E0.book Page 65 Monday, July 31, 2006 10:10 AM

Maintenance and care
66
EJU34210Checking the fuel system
WARNING
EWJ00380
Gasoline is highly flammable and explo-
sive. Failure to check for and repair any
fuel leakage could result in a fire or explo-
sion. A fire or explosion can cause severe
injury or death. Shut the engine off. Do not
smoke. Avoid spilling gasoline.
Fuel in the fuel lines is pressurized.
Fuel can spray out and cause injury or a
fire hazard if a fuel line is disconnected.
Do not run the engine with a fuel line dis-
connected.
Check the fuel system for leaks, cracks, and
malfunctions. If any problem is found, consult
a Yamaha dealer.
Check:

Fuel tank filler cap and seal for damage.

Fuel in fuel tank for water and dirt.

Fuel tank for damage, cracks, and leakage.

Fuel hoses and joints for damage, cracks,
and leakage.

Air bleeding passages for leakage.EJU34230Fuel tank
Check the fuel tank for leakage and for water
in the tank. If water is found in the fuel system,
or if the fuel tank needs to be cleaned, have a
Yamaha dealer service the watercraft.
EJU34240Checking the oil injection system
Check the oil injection system for leakage,
cracks, and malfunctions. Have a Yamaha
dealer repair the oil injection system if neces-
sary.
Check:

Oil tank for damage, cracks, and leakage.

Oil in the oil tank for water and dirt.

Oil hoses and joints for damage, cracks,
and leakage.

Oil filter for dirt.

Oil pump for leakage.EJU34250Oil tank
Check the oil tank for leakage and for water in
the tank. If water is found in the oil injection
system, or if the oil tank needs to be cleaned,
have a Yamaha dealer service the watercraft.
EJU34260Oil filter
Have a Yamaha dealer check the oil filter for
dirt and clogs.
EJU34320Checking the jet thrust nozzle angle
Check the handlebars and jet thrust nozzle for
smooth operation.
Turn the handlebars as far as possible to the
right and left and check that the difference of
distances A and B between the jet thrust noz-
zle and the nozzle is within specification.
1Fuel tank
UF1G74E0.book Page 66 Monday, July 31, 2006 10:10 AM

Maintenance and care
67
If the steering is stiff or misadjusted, have a
Yamaha dealer service it.
EJU34360Checking and adjusting the throttle
cable
Check that the throttle cable moves back to
the set position smoothly and that the throttle
lever free play is within specification.
(1) Squeeze and release the throttle lever. If
the throttle lever does not return smooth-
ly, have a Yamaha dealer service it.(2) Adjust the free play by loosening the lock-
nut and turning the adjuster.
EJU34371Cleaning and adjusting the spark
plugs
WARNING
EWJ00350
Be careful not to damage the insulator
when removing or installing a spark plug.
A damaged insulator could allow sparks to
escape, which could result in a fire or ex-
plosion.
The spark plug is an important engine compo-
nent and is easy to inspect. The condition of
the spark plug can indicate something about
the condition of the engine. For example, if the
center electrode porcelain is very white, this
could indicate an intake air leak or carburetion
problem in that cylinder. Do not attempt to di-
agnose any problems yourself. Have a
Yamaha dealer service the watercraft.
Remove and inspect the spark plugs periodi-
cally; heat and deposits will cause the spark
plugs to slowly break down and erode. If elec-
trode erosion becomes excessive, or if carbon Difference of A and B:
Maximum 5 mm (0.20 in)
1Locknut
2Adjuster
3Throttle lever free play
Throttle lever free play:
4.0–7.0 mm (0.16–0.28 in)
UF1G74E0.book Page 67 Monday, July 31, 2006 10:10 AM

Maintenance and care
71
EJU34490Fuel injection system
The fuel injection system was set at the
Yamaha factory. If the fuel injection system
needs to be adjusted, have a Yamaha dealer
service the watercraft.
CAUTION:
ECJ00220
Do not attempt to adjust the fuel injection
system. If the settings are disturbed by
someone who does not have the neces-
sary technical knowledge, poor engine
performance and damage may result.
EJU34500Checking the trolling speed
(1) Place the watercraft in the water.
(2) Start the engine and warm it up. Use the
tachometer in the multifunction informa-
tion center to check the trolling speed.
If the trolling speed is out of specification,
have a Yamaha dealer service the watercraft.
EJU34520Bleeding the oil pump
If the oil tank becomes completely empty, or
any hose connected to the oil pump has been
disconnected, the oil pump must be bled to
ensure proper oil flow.
If necessary, have a Yamaha dealer bleed the
oil pump.
EJU36190Adjusting the Yamaha Adjustable
Sponsons (YAS)
The Yamaha Adjustable Sponsons can be
adjusted to two positions to enhance water-
craft performance according to operator pref-
erence and operating conditions. (See page
33 for an explanation of the positions.)To adjust the YAS:
(1) Remove the bolts on both sponsons.
(2) Remove the sponsons, and then install
them in the desired position.
NOTE:
Be sure to install both sponsons in the same
position.
(3) Tighten the sponson bolts to the specified
torque. Trolling speed:
1350 ±100 r/min
1Bolt
Sponson bolt tightening torque:
18.0 Nm (13.3 ft-lb) (1.84 kgf-m)
UF1G74E0.book Page 71 Monday, July 31, 2006 10:10 AM

Trouble recovery
73
EJU34560
Troubleshooting
If you have any trouble with your watercraft, use this section to check for the possible cause.
If you cannot find the cause, or if the procedure for replacement or repair is not described in
this owner’s/operator’s manual, have a Yamaha dealer perform the necessary service.
EJU34580Troubleshooting chart
TROUBLE POSSIBLE CAUSE REMEDY PAGE
Engine does not
start (Starter motor
does not turn over)Engine shut-
off switchClip not in place Install clip
22
Fuse Burned out Replace the fuse and
check wiring78
Battery Run down Recharge 69
Poor terminal con-
nectionsTighten as required
69
Terminal corroded Clean 61
Starter motor Faulty Have serviced by
Yamaha dealer—
Warning sys-
temOverheat mode Cool down engine
29
Engine does not
start (Starter motor
turns over)Throttle lever Squeezed Release 23
Fuel Empty Refill as soon as pos-
sible36
Stale or contaminat-
edHave serviced by
Yamaha dealer66
Fuel tank Water or dirt present Have serviced by
Yamaha dealer66
Spark plug Fouled or defective Clean or replace 67
Spark plug
capNot connected or
looseConnect properly
67
Crankcase Filled with water Crank engine with
plug out until clean79
Fuel injec-
tion systemFuel pump faulty Have serviced by
Yamaha dealer—
Water tem -
perature sen-
sorFailed Have serviced by
Yamaha dealer 29
UF1G74E0.book Page 73 Monday, July 31, 2006 10:10 AM

Trouble recovery
74
Engine runs irregu-
larly or stallsFuel Empty Refill as soon as pos-
sible36
Stale or contaminat-
edHave serviced by
Yamaha dealer66
Fuel tank Water or dirt present Have serviced by
Yamaha dealer66
Spark plug Fouled or defective Replace 67
Incorrect heat range Replace 67
Gap incorrect Adjust 67
Spark plug
capLoose Connect properly 67
Cracked, torn, or
damagedReplace
—
Electrical wir-
ingLoose connection Tighten or connect
properly—
Fuel injec-
tion systemFaulty or clogged in-
jectorsHave serviced by
Yamaha dealer—
Warning light or in-
dicator blinksFuel level Empty Refill as soon as pos-
sible36
Engine oil
levelEmpty Refill immediately 36
Oil filter clogged Have serviced by
Yamaha dealer—
Engine over-
heatedJet intake clogged Clean 76
Water temperature
sensor is failedHave serviced by
Yamaha dealer29
Low battery
voltageBattery voltage low Charge 69
Battery terminal con-
nected wrongConnect properly
69
Exhaust gas
temperatureGas temperature is
too highCool down engine
31
Check engine
warningFaulty sensors Have serviced by
Yamaha dealer31 TROUBLE POSSIBLE CAUSE REMEDY PAGE
UF1G74E0.book Page 74 Monday, July 31, 2006 10:10 AM

Trouble recovery
76
EJU34620
Emergency procedures EJU34630Cleaning the jet intake and impeller
If weeds or debris get caught in the jet intake
or impeller, cavitation can occur, causing jet
thrust to decrease even though engine speed
rises. If this condition is allowed to continue,
the engine will overheat and may seize. If
there is any sign that the jet intake or impeller
is clogged with weeds or debris, return to
shore and check the intake and impeller. Al-
ways stop the engine before beaching the wa-
tercraft.
WARNING
EWJ00780
Before attempting to remove weeds or de-
bris from the jet intake or impeller area,
shut the engine off and remove the clip
from the engine shut-off switch. Severe in-
jury or death could result from coming incontact with the rotating parts of the jet
pump.
CAUTION:
ECJ00650
If weeds or debris get caught in the jet in-
take, do not operate the watercraft above
trolling speed until they have been re-
moved.
(1) Turn the watercraft on its side as shown.
UF1G74E0.book Page 76 Monday, July 31, 2006 10:10 AM

Index
2-stroke engine oil .................................... 36
A
Adjusting the Yamaha Adjustable
Sponsons (YAS) ................................... 71
B
Battery ................................................ 40, 61
Battery, checking...................................... 69
Battery, jumping ....................................... 77
Beaching the watercraft ........................... 57
Bilge ......................................................... 39
Boarding alone ......................................... 51
Boarding and starting from a dock ........... 51
Boarding and starting in deep water ........ 51
Boarding and starting in shallow water .... 50
Boarding with a passenger....................... 52
Bow down................................................. 26
Bow eye ................................................... 26
Bow up ..................................................... 26
Builder’s plate............................................. 2
C
Capsized watercraft ................................. 54
Check engine warning indicator ............... 31
Cleaning the watercraft ............................ 62
Cooling water pilot outlets .................. 23, 44
Cruising limitations ................................... 10
D
Docking the watercraft ............................. 57
E
Emergency procedures ............................ 76
Engine break-in ........................................ 45
Engine compartment ................................ 39
Engine overheat warning indicator ........... 29
Engine serial number ................................. 1
Engine shut-off cord ................................. 44
Engine shut-off switch .............................. 22
Engine stop switch ................................... 22
Enjoy your watercraft responsibly ............ 16
Exhaust temperature warning indicator.... 31
F
Filling the fuel tank ................................... 36
Filling the oil tank ..................................... 36
Fire extinguisher....................................... 41
Flushing the cooling system ..................... 60
Front storage compartment ...................... 32Fuel and oil............................................... 35
Fuel and oil systems ................................ 39
Fuel injection system ................................ 71
Fuel level meter ........................................ 28
Fuel level warning indicator ...................... 29
Fuel system .............................................. 61
Fuel system, checking .............................. 66
Fuel tank .................................................. 66
Fuel tank filler cap .................................... 22
Fuses, replacing ....................................... 78
G
Gasohol .................................................... 35
Gasoline ................................................... 35
Getting to know your watercraft ............... 48
Glove compartment .................................. 33
H
Handgrip ................................................... 26
Hazard information ................................... 14
Hood ......................................................... 21
Hour meter/voltmeter ............................... 28
Hull and deck ........................................... 39
Hull Identification Number (HIN)................. 1
I
Identification numbers ................................ 1
Important labels .......................................... 3
J
Jet intake .................................................. 43
Jet intake and impeller, cleaning .............. 76
Jet thrust nozzle angle, checking ............. 66
Jumper cables, connecting ...................... 77
L
Labels, other .............................................. 7
Labels, warning .......................................... 4
Launching the watercraft .......................... 46
Learning to operate your watercraft ......... 48
Leaving the watercraft .............................. 48
Limitations on who may operate the
watercraft ................................................ 9
Lubrication................................................ 61
Lubrication points ..................................... 68
M
Main components, location of .................. 17
Maintenance and adjustments ................. 63
Model information....................................... 2
Multifunction information center ......... 27, 44
UF1G74E0.book Page 1 Monday, July 31, 2006 10:10 AM