fuel cap YAMAHA GP1300R 2007 Owners Manual

Table of contents
General and important labels ........... 1
Identification numbers .................... 1
Primary Identification (PRI-ID)
number ........................................... 1
Hull Identification Number (HIN) ........ 1
Engine serial number ........................ 1
Model information ........................... 2
Builder’s plate .................................... 2
Important labels .............................. 3
Warning labels ................................... 4
Other labels ....................................... 7
Safety information ............................. 9
Limitations on who may operate
the watercraft .............................. 9
Cruising limitations ....................... 10
Operation requirements ............... 11
Recommended equipment ........... 13
Hazard information ....................... 14
Watercraft characteristics ............. 14
Safe boating rules ........................ 15
Enjoy your watercraft
responsibly ................................ 16
Features and functions ................... 17
Location of main components ...... 17
Operation of controls and other
functions .................................... 21
Seat ................................................. 21
Hood ................................................ 21
Fuel tank filler cap ........................... 22
Oil tank filler cap .............................. 22
Engine stop switch .......................... 22
Engine shut-off switch ..................... 22
Start switch ...................................... 23
Throttle lever ................................... 23
Cooling water pilot outlets ............... 23
Steering system ............................... 24
Quick Shift Trim System (QSTS)
selector ........................................ 25
Handgrip .......................................... 26
Bow eye ........................................... 26
Stern rope holes .............................. 27Yamaha Engine Management
System (YEMS) ........................... 27
Multifunction information center ...... 27
Storage compartments .................... 32
Yamaha Adjustable
Sponsons (YAS) .......................... 33
Operation ......................................... 35
Fuel and oil .................................. 35
Gasoline .......................................... 35
2-stroke engine oil ........................... 36
Filling the fuel tank .......................... 36
Filling the oil tank ............................. 36
Pre-operation checks ................... 38
Pre-operation check list ................... 38
Pre-operation check points .............. 39
Operation ..................................... 45
Engine break-in ............................... 45
Launching the watercraft ................. 46
Starting the engine .......................... 46
Stopping the engine ........................ 48
Leaving the watercraft ..................... 48
Operating your watercraft ............ 48
Getting to know your watercraft ....... 48
Learning to operate your
watercraft ..................................... 48
Riding with a passenger .................. 49
Starting the watercraft ..................... 50
Boarding and starting in
deep water ................................... 51
Capsized watercraft ......................... 54
Turning the watercraft ..................... 55
Stopping the watercraft ................... 56
Beaching the watercraft ................... 57
Docking the watercraft ..................... 57
Rough water operation .................... 57
Post-operation care ...................... 58
Transporting ................................. 59
Maintenance and care .................... 60
Storage ........................................ 60
Flushing the cooling system ............ 60
Lubrication ....................................... 61
Fuel system ..................................... 61
UF1G74E0.book Page 1 Monday, July 31, 2006 10:10 AM

Features and functions
18
Rear view
1Fuel tank filler cap
2Intake grate
3Speed sensor
4Stern drain plugs
5Ride plate
6Jet thrust nozzle
7Stern rope hole
8Handgrip
9Glove compartment
UF1G74E0.book Page 18 Monday, July 31, 2006 10:10 AM

Features and functions
20
Engine compartment
1Spark plugs/Spark plug caps
2Electrical box
3Flushing hose connector
4Spark plug lead
5Muffler
6Fuel tank
7Oil tank
8Battery
9Fire extinguisher container
10Water separator
UF1G74E0.book Page 20 Monday, July 31, 2006 10:10 AM

Features and functions
22
To close the hood, push the hood down to
lock it in place.
NOTE:
Make sure that the hood is securely closed
before operating the watercraft.
EJU31090Fuel tank filler cap
To remove the fuel tank filler cap, turn it coun-
terclockwise.
NOTE:
Make sure that the fuel tank filler cap is se-
curely closed before operating the watercraft.
EJU31100Oil tank filler cap
To remove the oil tank filler cap, turn it coun-
terclockwise.
NOTE:
Make sure that the oil tank filler cap is secure-
ly closed before operating the watercraft.
EJU31150Engine stop switch
Push the engine stop switch (red button) to
stop the engine normally.
EJU31160Engine shut-off switch
Insert the clip, on the end of the engine shut-
off cord, under the engine shut-off switch
(black button). The engine will stop automati-
cally when the clip is removed from the
1Fuel tank filler cap
1Oil tank filler cap
1Engine stop switch
UF1G74E0.book Page 22 Monday, July 31, 2006 10:10 AM

Features and functions
27
The bow eye is used to attach a rope to the
watercraft when transporting, mooring, or
towing it in an emergency.
EJU36020Stern rope holes
The stern rope holes are located at the stern
of the watercraft.
The stern rope holes are used to attach a rope
to the watercraft when transporting or moor-
ing it.
EJU31370Yamaha Engine Management System
(YEMS)
This model is equipped with an integrated,
computerized management system that con-
trols and adjusts ignition timing, fuel injection,
engine diagnostics, and the off-throttle steer-
ing (OTS) system.
EJU31420Multifunction information center
This meter contains the following functions for
help and convenience in operating the water-
craft.
CAUTION:
ECJ00060

Do not run the engine over 4000 r/min
when checking the operation of the
meter on land without supplying water,
otherwise the engine could overheat
and the catalytic converter could be se-
riously damaged.

Use the specified resistor-type spark
plugs and caps, otherwise the meter
may function erratically.
NOTE:

When the engine is started, all displays light
up for a few seconds, the buzzer sounds
twice, and then the meter starts to operate
normally.
1Bow eye
1Stern rope hole
1Tachometer
2Speedometer
3Hour meter/voltmeter
4Fuel level meter
5“WARNING” light
6Fuel level warning indicator
7Oil level warning indicator
8Engine overheat warning indicator
9Exhaust temperature warning indicator
10Check engine warning indicator
11Select button
UF1G74E0.book Page 27 Monday, July 31, 2006 10:10 AM

Operation
35
EJU31800
Fuel and oil
This engine uses Yamaha’s oil injection sys-
tem, which provides superior lubrication by
ensuring the proper fuel-to-oil ratio for all op-
erating conditions. No fuel premixing is nec-
essary, except during the engine break-in
period. Simply pour gasoline into the fuel tank
and oil into the oil tank.
The engine utilizes an electronic fuel injection
system to deliver the optimal air-fuel ratio re-
quired by the engine. By ensuring the optimal
combustion conditions, this system is able to
increase startability and improve fuel econo-
my.
EJU31850Gasoline
WARNING
EWJ00440
GASOLINE AND ITS VAPORS ARE HIGH-
LY FLAMMABLE AND EXPLOSIVE!

Do not smoke when refueling, and keep
away from sparks, flames, and other
sources of ignition.

Stop the engine before refueling.

Refuel in a well-ventilated area with the
watercraft in a horizontal position.

Do not stand or sit on the watercraft
while refueling in case of fire.

Take care not to spill gasoline. If gaso-
line spills, wipe it up immediately with
dry rags. Always properly dispose of
gasoline-soaked rags.

Avoid overfilling the fuel tank. Stop fill-
ing when the fuel level just reaches the
bottom of the filler tube. Do not fill up the
filler tube because fuel expands as it
warms up and could overflow. If tempo-
rarily leaving the watercraft with a full
fuel tank, do not leave it in direct sun-
light. Leave it in a well-ventilated areawith the watercraft in a horizontal posi-
tion.

Tighten the fuel tank filler cap securely
after refueling.

If you should swallow some gasoline, in-
hale a lot of gasoline vapor, or get gaso-
line in your eyes, get immediate medical
attention.

If any gasoline spills on your skin or
clothing, immediately wash the affected
area with soap and water and change
your clothes.
CAUTION:
ECJ00320

Do not use leaded gasoline. Leaded gas-
oline can seriously damage the catalytic
converter.

Use only fresh gasoline that has been
stored in clean containers.
EJU31860Gasohol
There are two types of gasohol: gasohol con-
taining ethanol and that containing methanol.
Gasohol containing ethanol can be used if
ethanol content does not exceed 10% and the
fuel meets the minimum octane ratings.
Gasohol containing methanol is not recom-
mended by Yamaha because it can cause
fuel system damage and engine performance
problems.Recommended gasoline:
Regular unleaded gasoline with a mini-
mum octane rating of
86 (Pump octane number) = (R +
M)/2
90 (Research octane number)
UF1G74E0.book Page 35 Monday, July 31, 2006 10:10 AM

Operation
36
EJU318802-stroke engine oil
CAUTION:
ECJ00270
Use only YAMALUBE 2-W engine oil, oth-
erwise the catalytic converter and other
engine components could be seriously
damaged.
NOTE:
YAMALUBE 2-W engine oil is developed for
this watercraft and available from a Yamaha
dealer.
EJU31920Filling the fuel tank
CAUTION:
ECJ00290
Be careful when refueling. Avoid getting
water and other contaminants in the fuel
tank. Contaminated fuel can cause poor
running and engine damage.
(1) Open the hood, remove the front storage
compartment, and then check the fuel
level. (See “Front storage compartment”
on page 32 for more information.)
(2) Remove the fuel tank filler cap, and then
slowly add fuel to the fuel tank. Stop fillingwhen the fuel level just reaches the bot-
tom of the filler tube.
(3) Install the fuel tank filler cap and front
storage compartment, and then close the
hood.
NOTE:
Do not fill up the filler tube because fuel ex-
pands as it warms up and could overflow.
EJU31960Filling the oil tank
WARNING
EWJ00420

Do not add gasoline to the oil tank. Fire
or explosion could result.

Oil in the bilge is a serious fire hazard.
Wipe up any spilled oil immediately.
CAUTION:
ECJ00300
Do not allow the oil tank to become com-
pletely empty. If the oil tank becomes emp-
ty, the oil pump must be bled to ensure
proper oil flow, otherwise engine damage
could result. If necessary, have a Yamaha
dealer bleed the oil pump.
(1) Remove the seat to view the oil level.
(See page 21 for seat removal and instal-
lation procedures.) Recommended engine oil:
YAMALUBE 2-W
Fuel tank capacity:
60.0 L (15.9 US gal) (13.2 Imp.gal)
UF1G74E0.book Page 36 Monday, July 31, 2006 10:10 AM

Operation
39
EJU32280Pre-operation check points EJU32300Engine compartment
Ventilate the engine compartment before
each use.
To ventilate the engine compartment, remove
the seat and front storage compartment. (See
“Seat” on page 21 and “Front storage com-
partment” on page 32 for more information.)
Leave the engine compartment open for a few
minutes to allow any fuel vapors to escape.
While the engine compartment is open, check
for loose electrical connections.
WARNING
EWJ00460
Failure to ventilate the engine compart-
ment could result in a fire or explosion. Do
not start the engine if there is a fuel leak or
a loose electrical connection.
EJU32350Hull and deck
Check the hull and deck for cracks and other
damage. If any damage is found, have a
Yamaha dealer repair the watercraft.
EJU32371Fuel and oil systems
Check the fuel system for leakage, cracks,
and malfunctions before each use. (See page
66 for check points and correct procedures.)
(1) Remove the fuel tank filler cap to release
any pressure that might have built up in
the fuel tank.(2) Remove the seat and front storage com-
partment. (See “Seat” on page 21 and
“Front storage compartment” on page 32
for more information.)
(3) Check the fuel and oil levels in the tanks
and replenish if necessary. (See page 36
for refueling procedures and page 36 for
oil tank filling procedures.)
(4) Install the fuel tank filler cap, seat, and
front storage compartment.
EJU32420Water separator
Check the water separator for water. The wa-
ter separator retains any water that may have
entered through the fuel tank breather hose if
the watercraft was capsized. Normally, the
water separator is empty.
If water remains in the water separator, drain
it by removing the drain screw. Place a drain
pan under the water separator to catch the
draining water or use a dry cloth to soak up
any water that could spill into the watercraft. If
any water spills into the watercraft, be sure to
wipe it up with a dry cloth. Also, be sure to in-
stall the drain screw after draining the water
separator.
EJU32440Bilge
Check the bilge for moisture and fuel residue.
This watercraft is equipped with a convention-
al jet vacuum bilge draining system and an
1Water separator
2Drain screw
UF1G74E0.book Page 39 Monday, July 31, 2006 10:10 AM

Maintenance and care
60
EJU33490
Storage
WARNING
EWJ00330
Always place the watercraft upright in a
horizontal position when storing it, other-
wise fuel could leak out into the engine or
engine compartment, which could create a
fire hazard.
Storage for long periods of time, such as win-
ter storage, requires preventive maintenance
to ensure against deterioration. It is advisable
to have the watercraft serviced by a Yamaha
dealer prior to storage. However, the following
procedures can be performed by the owner.
EJU33520Flushing the cooling system
Flushing the cooling system is essential to
prevent it from clogging with salt, sand, or dirt.
WARNING
EWJ00270
Do not start the engine on land if anyone is
behind the watercraft. Hot water and
steam spurting from the exhaust outlet
into the air can cause serious burns.
CAUTION:
ECJ00130

Do not supply water to the cooling water
passages when the engine is not run-
ning. The water could flow back through
the muffler into the crankcase, causing
severe engine damage.

Do not run the engine for more than 15
seconds on land without supplying wa-
ter, otherwise the engine could over-
heat.

Do not run the engine over 4000 r/min on
land, otherwise the catalytic converter
could be seriously damaged.
(1) Remove the watercraft from the water
and place it in a horizontal position.(2) Remove the flushing hose connector
cap, and then insert the garden hose
adapter into the flushing hose connector
and turn it until it is securely connected.
(3) Connect the garden hose adapter to a
water tap using a garden hose.
NOTE:
A garden hose is not included and must be
purchased separately.
(4) Start the engine, and then immediately
turn the water supply on until water flows
out continually from the cooling water pi-
lot outlet.
(5) Run the engine at idling speed for about
3 minutes watching the engine condition.
If the engine stops while flushing, turn the
water supply off immediately and repeat
the above steps.
(6) Turn the water supply off, and then force
the remaining water out of the cooling
water passages by running the engine at
4000 r/min or less for 10 to 15 seconds.
(7) Stop the engine.
(8) Remove the garden hose adapter and in-
stall the flushing hose connector cap.
1Flushing hose connector cap
2Garden hose adapter
3Flushing hose connector
UF1G74E0.book Page 60 Monday, July 31, 2006 10:10 AM

Maintenance and care
61
EJU33580Lubrication
WARNING
EWJ00260
Do not spray flammable rust inhibitor
products on engine surfaces while the en-
gine is hot. The sprayed substance or pro-
pellants could catch fire.
(1) Remove the spark plugs and pour ap-
proximately one tablespoon of engine oil
into each cylinder.
(2) Grease the spark plug threads and rein-
stall the spark plugs.
(3) With the spark plug caps removed from
the spark plugs, crank the engine for 3
seconds or less using the start switch.
(4) Lubricate all cables such as the throttle
and steering cables.
NOTE:
Use a suitable marine grease applicator to
pressure-lubricate the cables and purge out
any moisture between the inner and outer ca-
bles.
(5) Lubricate the areas of the watercraft
specified in “Lubrication points” on page
68.
EJU33651Fuel system
WARNING
EWJ00290
GASOLINE AND ITS VAPORS ARE HIGH-
LY FLAMMABLE AND EXPLOSIVE!

Do not smoke when refueling, and keep
away from sparks, flames, and other
sources of ignition.

Stop the engine before refueling.

Refuel in a well-ventilated area with the
watercraft in a horizontal position.

Do not stand or sit on the watercraft
while refueling in case of fire.

Take care not to spill gasoline. If gaso-
line spills, wipe it up immediately with
dry rags. Always properly dispose of
gasoline-soaked rags.

Avoid overfilling the fuel tank. Stop fill-
ing when the fuel level just reaches the
bottom of the filler tube. Do not fill up the
filler tube because fuel expands as it
warms up and could overflow. If tempo-
rarily leaving the watercraft with a full
fuel tank, do not leave it in direct sun-
light. Leave it in a well-ventilated area
with the watercraft in a horizontal posi-
tion.

Tighten the fuel tank filler cap securely
after refueling.

If you should swallow some gasoline, in-
hale a lot of gasoline vapor, or get gaso-
line in your eyes, get immediate medical
attention.

If any gasoline spills on your skin or
clothing, immediately wash the affected
area with soap and water and change
your clothes.
Top off the fuel tank with fresh gasoline and
add 470 ml (15.9 US oz, 16.5 Imp oz) of
Yamaha Fuel Stabilizer and Conditioner.
CAUTION:
ECJ00140
Use only Yamaha Fuel Stabilizer and Con-
ditioner, otherwise the catalytic converter
could be seriously damaged.
EJU33680Battery
If the watercraft will not be used for more than
a month, remove the battery from the water-
craft and store it in a cool, dry place.
(1) Disconnect the negative (–) battery lead
first, then the positive (+) battery lead and
breather hose, and then remove the bat-
tery from the watercraft.
UF1G74E0.book Page 61 Monday, July 31, 2006 10:10 AM