YAMAHA TTR50 2006 Repair Manual

SPEC
2 - 6
Stem runout limit ---- 0.01 mm
(0.0004 in)
Valve seat width IN 0.9 ~ 1.1 mm (0.0354 ~ 0.0433 in)1.6 mm
(0.0630 in)
EX 0.9 ~ 1.1 mm (0.0354 ~ 0.0433 in) 1.6 mm
(0.0630 in)
Valve spring: Free length IN 32.45 mm (1.28 in) 30.83 mm (1.21 in)
EX 32.45 mm (1.28 in) 30.83 mm (1.21 in)
Set length (valve closed) IN 24.2 mm (0.95 in) ---- EX 24.2 mm (0.95 in) ----
Compressed pressure (installed) IN 138 ~ 158 N (14.07 ~ 16.11 kg,
31.02 ~ 35.52 lb)----
EX 138 ~ 158 N (14.07 ~ 16.11 kg,
31.02 ~ 35.52 lb) ----
Tilt limit IN ----
2.5 °/1.4 mm
(2.5 °/0.06 in)
EX ----2.5 °/1.4 mm
(2.5 °/0.06 in)
Direction of winding (top view) IN Clockwise ----
EX Clockwise ----
Item Standard Limit
*
MAINTENANCE SPECIFICATIONS

SPEC
2 - 7
Piston:
Piston to cylinder clearance 0.030 ~ 0.040 mm (0.0012 ~ 0.0016 in)0.15 mm
(0.0059 in)
Piston size “D ” 35.960 ~ 35.980 mm
(1.4157 ~ 1.4165 in) ----
Measuring point “H ” 5 mm (0.20 in) ----
Piston off-set 0.50 mm (0.0197 in) ----
Offset direction Intake side ----
Piston pin bore inside diameter 12.002 ~ 12.013 mm (0.4725 ~ 0.4730 in)12.043 mm
(0.4741 in)
Piston pin outside diameter 11.996 ~ 12.000 mm (0.4723 ~ 0.4724 in)11.976 mm
(0.4715 in)
Piston rings: Top ring
Type Barrel ----
Dimensions (B × T) 0.80 × 1.60 mm
(0.031 × 0.063 in) ----
End gap (installed) 0.10 ~ 0.25 mm (0.004 ~ 0.010 in)0.50 mm
(0.020 in)
Side clearance (installed) 0.020 ~ 0.070 mm (0.0008 ~ 0.0028 in)0.12 mm
(0.0047 in)
2nd ring
Type Taper ----
Dimensions (B × T) 0.80 × 1.60 mm
(0.031 × 0.063 in) ----
End gap (installed) 0.15 ~ 0.30 mm (0.006 ~ 0.012 in)0.65 mm
(0.026 in)
Side clearance 0.020 ~ 0.060 mm (0.0008 ~ 0.0024 in)0.12 mm
(0.0047 in)
Item Standard Limit
H
D
T
B
B
T
MAINTENANCE SPECIFICATIONS

SPEC
2 - 8
Oil ring
Dimensions (B × T) 1.50 × 1.60 mm
(0.059 × 0.063 in) ----
End gap (installed) 0.20 ~ 0.70 mm (0.008 ~ 0.028 in)----
Crankshaft: Crank width “A” 42.95 ~ 43.00 mm (1.691 ~ 1.693 in)----
Runout limit “C” ---- 0.03 mm (0.0012 in)
Big end side clearance “D” 0.10 ~ 0.40 mm (0.0039 ~ 0.0157 in)0.50 mm
(0.02 in)
Big end radial clearance “E” 0.010 ~ 0.025 mm (0.0004 ~ 0.0010 in)0.05 mm
(0.002 in)
Clutch: Friction plate Thickness 2.92 ~ 3.08 mm (0.115 ~ 0.121 in)2.82 mm
(0.111 in)
Quantity 2 ----
Clutch plate 1 Thickness 1.85 ~ 2.15 mm (0.073 ~ 0.085 in)----
Quantity 1 ----
Warp limit ---- 0.2 mm (0.008 in)
Clutch plate 2 Thickness 1.95 ~ 2.05 mm (0.077 ~ 0.081 in)----
Quantity 1 ----
Warp limit ---- 0.2 mm (0.008 in)
Clutch plate 3 Thickness 1.90 ~ 2.10 mm (0.075 ~ 0.083 in)----
Quantity 1 ----
Warp limit ---- 0.2 mm (0.008 in)
Automatic centrifugal clutch: Clutch-in revolution 2,300 ~ 2,700 r/min ----
Clutch-stall revolution 3,210 ~ 3,710 r/min ----
Shifter: Shifter type Shift drum and guide bar ---- Item Standard Limit
B
T
CC
D
A
E
MAINTENANCE SPECIFICATIONS

SPEC
2 - 9
Carburetor:
I. D. mark 1P61 00 ----
Main jet (M.J) #62.5 ----
Main nozzle (N.J) E-2M ----
Main air jet (M.A.J) ø 1.4 ----
Jet needle (J.N) 4DL22-1 ----
Cutaway (C.A) 2.5 ----
Pilot outlet (P.O) ø 0.8 × 1.5 ----
Pilot jet (P.J) #12.5 ----
Valve seat size (V.S) ø 1.2 ----
Starter jet 1 (G.S.1) #20 ----
Starter jet 2 (G.S.2) ø 0.6 ----
Float height (F.H) 18.5 mm (0.73 in) ----
Fuel level (F.L) 2.0 ~ 3.0 mm (0.08 ~ 0.12 in) ----
Engine idle speed 1,600 ~ 1,800 r/min ----
Lubrication system: Oil filter type Wire mesh type ----
Oil pump type Trochoid type ----
Inner-rotor-to-outer-rotor-tip clearance 0.15 mm or less (0.0061 in or less)0.20 mm
(0.0079 in)
Outer-rotor-to-oil-pump-housing clearance 0.07 mm (0.0028 in)0.15 mm
(0.0059 in)
Oil-pump-housing-to-inner-rotor-and-outer-
rotor clearance 0.06 ~ 0.10 mm
(0.0024 ~ 0.0039 in)0.17 mm
(0.0067 in)
Item Standard Limit
MAINTENANCE SPECIFICATIONS

SPEC
2 - 10
Part to be tightened Thread size Q
’ty Tightening torque
Remarks
Nm m ·kg ft ·lb
Cylinder head nut M8 × 1.25 4 22 2.2 16
Cylinder head bolt M6 × 1.0 2 10 1.0 7.2
Spark plug M10 × 1.0 1 13 1.3 9.4
Camshaft sprocket cover bolt M6 × 1.0 2 10 1.0 7.2
Tappet cover M45 × 1.5 2 18 1.8 13
Exhaust pipe stud bolt M6 × 1.0 2 7 0.7 5.1
Rotor nut M12 × 1.25 1 48 4.8 35
Timing chain guide stopper M6 × 1.0 2 10 1.0 7.2
LT
Valve clearance adjust screw locknut M5 × 0.5 2 7 0.7 5.1
Camshaft sprocket M8 × 1.25 1 26 2.6 19
Camshaft bearing retainer M6 × 1.0 1 10 1.0 7.2
LT
Timing chain tensioner cap bolt M8 × 1.25 1 8 0.8 5.8
Timing chain tensioner M6 × 1.0 2 10 1.0 7.2
Oil pump assembly M6 × 1.0 2 7 0.7 5.1
LT
Engine oil drain bolt M12 × 1.5 1 20 2.0 14
Intake manifold (cylinder head side) M6 × 1.0 2 7 0.7 5.1
Intake manifold (carburetor side) M6 × 1.0 2 7 0.7 5.1
Carburetor heater M8 × 1.25 1 3 0.3 2.2
Clamp (air filter joint) M4 × 0.7 1 2 0.2 1.4
Exhaust pipe M6 × 1.0 2 7 0.7 5.1
Muffler M8 × 1.25 1 38 3.8 27
Muffler cover M6 × 1.0 4 7 0.7 5.1
Spark arrester M6 × 1.0 3 10 1.0 7.2
Crankcase M6 × 1.0 10 10 1.0 7.2
Crankcase cover (left) M6 × 1.0 8 10 1.0 7.2
Drive sprocket cover M6 × 1.0 2 7 0.7 5.1
Timing plug M14 × 1.5 1 7 0.7 5.1
Crankshaft end cover M32 × 1.5 1 7 0.7 5.1
Crankcase cover (right) M6 × 1.0 9 10 1.0 7.2
Clutch adjuster locknut M8 × 1.25 1 6 0.6 4.3
Cylinder head stud bolt M8 × 1.25 4 13 1.3 9.4
Starter clutch and rotor M6 × 1.0 3 14 1.4 10 Stake
Clutch housing nut M14 × 1.0 1 70 7.0 50
Pressure plate M5 × 0.8 3 5 0.5 3.6
Primary driven gear M14 × 1.0 1 70 7.0 50
Stopper bolt M8 × 1.25 1 23 2.3 17
LT
Shift pedal M6 × 1.0 1 10 1.0 7.2
Pickup coil M6 × 1.0 2 10 1.0 7.2
LT
Stator assembly M6 × 1.0 3 10 1.0 7.2LT
Neutral switch M10 × 1.25 1 18 1.8 13
MAINTENANCE SPECIFICATIONS

SPEC
2 - 11
CHASSIS
Item Standard Limit
Steering system: Steering bearing type Angular bearing ----
Front suspension: Front fork travel 96 mm (3.78 in) ----
Spring rate K1 7.95 N/mm (0.81 kgf/mm, 45.39 lb/in)----
K2 10.50 N/mm (1.07 kgf/mm, 59.96 lb/in) ----
Optional spring/spacer No ----
Inner tube outer diameter 21.7 mm (0.85 in) ----
Rear suspension: Shock absorber travel 47 mm (1.85 in) ----
Spring free length 114 mm (4.49 in) ----
Fitting length 110 mm (4.33 in) ----
Spring rate, STD K = 29.0 N/mm (2.96 kg/mm, 166 lb/in)----
Optional spring No ----
Swingarm: Swingarm free play limit End ---- 1.0 mm (0.0394 in)
Side clearance ---- 0.3 mm (0.0118 in)
Wheel: Front wheel type Spoke wheel ----
Rear wheel type Spoke wheel ----
Front rim size/material 10 × 1.40/steel ----
Rear rim size/material 10 × 1.40/steel ----
Rim runout limit: Radial ---- 2.0 mm (0.08 in)
Lateral ---- 2.0 mm (0.08 in)
Drive chain: Type/manufacturer 420/KMC ----
Number of links 79 links + joint ----
Chain slack 35 ~ 45 mm (1.38 ~ 1.77 in) ----
Chain length (15 links) ---- 194.3 mm (7.65 in)
MAINTENANCE SPECIFICATIONS

SPEC
2 - 12
Drum brake:
Front drum brake type Leading, trailing ----
Rear drum brake type Leading, trailing ----
Front drum inside diameter 80 mm (3.15 in) 80.5 mm (3.17 in)
Rear drum inside diameter 80 mm (3.15 in) 80.5 mm (3.17 in)
Front lining thickness 3.5 mm (0.14 in) 1.5 mm (0.06 in)
Rear lining thickness 3.5 mm (0.14 in) 1.5 mm (0.06 in)
Brake lever and brake pedal: Brake lever free play (lever end) 10 ~ 20 mm (0.39 ~ 0.79 in) ----
Brake pedal free play 10 ~ 20 mm (0.39 ~ 0.79 in) ----
Throttle grip free play 3 ~ 5 mm (0.12 ~ 0.20 in) ---- Item Standard Limit
MAINTENANCE SPECIFICATIONS

SPEC
2 - 13
NOTE:
1.First, tighten the ring nut approximately 38 Nm (3.8 m · kg, 27 ft · lb) by using the lower ring nut
wrench and turn the steering right and left a few times; then loosen the lower ring nut completely.
2.Retighten the lower ring nut 4 Nm (0.4 m · kg, 2.9 ft · lb).
Part to be tightened Thread size Q
’ty Tightening torque
Nm m ·kg ft ·lb
Engine mounting: Engine and frame (front upper side) M8 × 1.25 1 30 3.0 22
Engine and frame (rear upper side) M8 × 1.25 1 30 3.0 22
Engine and frame (rear lower side) M10 × 1.25 1 48 4.8 35
Engine bracket and frame M8 × 1.25 2 30 3.0 22
Front wheel axle and front wheel axle nut M12 × 1.25 1 35 3.5 25
Front brake camshaft lever and front brake
camshaft M6
× 1.0 1 7 0.7 5.1
Front brake cable locknut M8 × 1.25 1 16 1.6 11
Front wheel nipple (spoke) —28 2 0.2 1.4
Rear wheel nipple (spoke) —28 2 0.2 1.4
Rear wheel axle and rear wheel axle nut M12 × 1.25 1 60 6.0 43
Rear brake camshaft lever and rear brake
camshaft M6
× 1.0 1 7 0.7 5.1
Rear wheel drive hub and rear wheel sprocket M8 × 1.25 4 25 2.5 18
Drive chain puller locknut M6 × 1.0 2 7 0.7 5.1
Upper bracket and handlebar M10 × 1.25 2 32 3.2 23
Steering stem nut M22 × 1.0 1 110 11.0 80
Lower ring nut M25 1 Refer to NOTE.
Upper bracket and lower bracket M10 × 1.25 2 32 3.2 23
Inner tube assembly and front fork guard M6 × 1.0 4 7 0.7 5.1
Pivot shaft and nut M10 × 1.25 1 35 3.5 25
Rear shock absorber and frame M10 × 1.25 1 30 3.0 22
Rear shock absorber and swingarm M10 × 1.25 1 30 3.0 22
Drive chain guide and swingarm M6 × 1.0 2 7 0.7 5.1
Drive chain support and swingarm M6 × 1.0 3 7 0.7 5.1
Drive chain guard and swingarm M6 × 1.0 2 7 0.7 5.1
Upper bracket and front fender M6 × 1.0 2 7 0.7 5.1
Fuel tank and fuel cock M6 × 1.0 2 7 0.7 5.1
Fuel tank and frame M6 × 1.0 2 7 0.7 5.1
Air scoop and fuel tank M6 × 1.0 2 7 0.7 5.1
Seat assembly and frame M6 × 1.0 2 7 0.7 5.1
Seat and rear fender M6 × 1.0 3 7 0.7 5.1
Seat and side covers M6 × 1.0 4 7 0.7 5.1
Footrest, under cover and engine M8 × 1.25 4 30 3.0 22
Sidestand and sidestand bracket M10 × 1.25 1 40 4.0 29
MAINTENANCE SPECIFICATIONS

SPEC
2 - 14
EC212300
ELECTRICALItem Standard Limit
Ignition system: Advancer Digital ----
CDI: Magneto-model/manufacturer F1P6/MORIC ----
Pickup coil resistance (color) 248 ~ 372 Ω at 20 °C (68 °F)
(Red – White) ----
CDI unit model/manufacturer 1P6/SHY ----
Ignition coil: Model/manufacturer 4FP/SHY ----
Minimum spark gap 6 mm (0.24 in) ----
Primary winding resistance 0.32 ~ 0.48 Ω at 20 °C (68 °F) ----
Secondary winding resistance 5.68 ~ 8.52 k Ω at 20 °C (68 °F) ----
Spark plug cap: Type Resin ----
Resistance 10 k Ω at 20 °C (68 °F) ----
Charging system: System type AC magneto ----
Model/manufacturer F1P6/SHY ----
Normal output 14 V/80 W at 5,000 r/min ----
Charging coil resistance (color) 0.96 ~ 1.44 Ω at 20 °C (68 °F)
(White – Black) ----
Lighting coil resistance (color) 0.80 ~ 1.20 Ω at 20 °C (68 °F)
(Yellow – Black) ----
Rectifier/regulator: Regulator type Semiconductor short circuit ----
Model/manufacturer SH620B-12/SHINDENGEN ----
No-load regulated voltage (DC) 14.0 ~ 15.0 V ----
No-load regulated voltage (AC) 13.0 ~ 14.0 V ----
Rectifier capacity 8 A ----
Battery: Model YT4B-BS or GT4B-5 ----
Voltage capacity 12 V 2.3 Ah or 12 V 2.5 Ah ----
Electric starting system: Type Constant mesh ----
Starter motor: Model/manufacturer 1P6/SHY ----
Operation voltage 12 V ----
Output 0.25 kW ----
Armature coil resistance 0.035 ~ 0.043 Ω at 20 °C (68 °F) ----
Brush overall length 7 mm (0.28 in) 3.5 mm (0.14 in)
Brush quantity 2 pcs. ----
MAINTENANCE SPECIFICATIONS

SPEC
2 - 15
Spring force 3.92 ~ 5.88 N
(400 ~ 600 g, 14.1 ~ 21.2 oz)3.92 N
(400 g,
14.1 oz)
Commutator diameter 17.6 mm (0.69 in) 16.6 mm (0.65 in)
Mica undercut (depth) 1.35 mm (0.05 in) ----
Starter relay: Model/manufacturer ACA12115-1/NAis ----
Amperage rating 30 A ----
Coil winding resistance 72.00 ~ 88.00 Ω at 20 °C (68 °F) ----
Fuse (amperage × quantity):
Main fuse 10 A × 1 ----
Reserve fuse 10 A × 1 ----
Item Standard Limit
MAINTENANCE SPECIFICATIONS