cooling YAMAHA TZR50 2012 Owners Manual

FOR YOUR SAFETY – PRE-OPERATION CHECKS
4-1
4
EAU15596
Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the ins-
pection and maintenance procedures and schedules described in the Owner’s Manual.
EWA11151
Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equipment dama-
ge. Do not operate the vehicle if you find any problem. If a problem cannot be corrected by the procedures pro-
vided in this manual, have the vehicle inspected by a Yamaha dealer.
Before using this vehicle, check the following points:
WARNING
ITEMCHECKS PAGE
• Check fuel level in fuel tank.
Fuel • Refuel if necessary. 3-8
• Check fuel line for leakage.
• Check oil level in oil tank.
2-stroke engine oil • If necessary, add recommended oil to specified level. 3-10
• Check vehicle for oil leakage.
Transmission oil • Check oil level in transmission case.
• If necessary, add recommended oil to specified level. 6-13
• Check coolant level in reservoir.
Coolant • If necessary, add recommended coolant to specified level. 6-14
• Check cooling system for leakage.
• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
Front brake • Replace if necessary. 6-23, 6-24
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.
1HD-F819D-E0 7/3/11 20:27 Página 31
2AS-F819D-E0.indd 3131/07/12 10:09

NOTICE: If coolant is not avai-
lable, use distilled water or soft
tap water instead. Do not use
hard water or salt water since it
is harmful to the engine. If
water has been used instead of
coolant, replace it with coolant
as soon as possible, otherwise
the cooling system will not be
protected against frost and
corrosion. If water has been
added to the coolant, have a
Yamaha dealer check the anti-
freeze content of the coolant
as soon as possible, otherwise
the effectiveness of the coolant
will be reduced.
[ECA10472]
1. Coolant reservoir cap
5. Install the panel.
EAUS2070
To change the coolant 1. Place the vehicle on a level surfa- ce and let the engine cool if
necessary.
2. Remove cowlings A, B and C and panel A. (See page 6-8).
3. Place a container under the engi- ne to collect the used coolant.
4. Remove the radiator cap retai- ning bolt, radiator cap retainer
and radiator cap. WARNING!
Never attempt to remove the
radiator cap when the engine is
hot.
[EWA10381]
1. Radiator cap retaining bolt
2. Radiator cap
3. Radiator cap retainer
5. Remove the coolant drain boltand its gasket to drain the coo-
ling system.
1. Coolant drain bolt
2. Gasket
Coolant reservoir capacity (up to
the maximum level mark):0.29 L (0.31 US qt, 0.26 Imp.qt)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-15
6
1HD-F819D-E0 7/3/11 20:27 Página 52
2AS-F819D-E0.indd 5231/07/12 10:09

6. Remove the coolant reservoircap.
1. Coolant reservoir cap
7. Move the hose clamp in thedirection shown, and then dis-
connect the coolant reservoir
hose to drain the reservoir.
1. Hose clamp
2. Coolant reservoir hose
3. Coolant reservoir
8. After the coolant is completely
drained, thoroughly flush the
cooling system with clean tap
water.
9. Connect the coolant reservoir hose, and then move the hose
clamp back to its original posi-
tion.
10. Install the coolant drain bolt and its new gasket, and then tighten
the bolt to the specified torque.
11. Pour the recommended coolant into the reservoir to the maximum
level mark, and then install the
coolant reservoir cap.
12. Pour the recommended coolant into the radiator until it is full. 13. Install the radiator cap, start the
engine, let it idle for several minu-
tes, and then turn it off.
14. Remove the radiator cap to check the coolant level in the
radiator. If necessary, add suffi-
cient coolant until it reaches the
top of the radiator, and then ins-
tall the radiator cap, retainer and
retaining bolt.
15. Check the coolant level in the reservoir. If necessary, remove
the coolant reservoir cap, add
coolant to the maximum level
mark, and then install the cap.Antifreeze/water mixture ratio:1:1
Recommended antifreeze: High-quality ethylene glycol
antifreeze containing corrosion
inhibitors for aluminum engines
Coolant quantity: Radiator capacity (including all
routes): 0.70 L (0.74 US qt, 0.62 Imp.qt)
Coolant reservoir capacity (up to
the maximum level mark): 0.29 L (0.31 US qt, 0.26 Imp.qt)
Tightening torque:Coolant drain bolt: 9 Nm (0.9 m•kgf, 6.5 ft•lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-16
6
1HD-F819D-E0 7/3/11 20:27 Página 53
2AS-F819D-E0.indd 5331/07/12 10:09

16. Start the engine, and then checkthe vehicle for coolant leakage. If
coolant is leaking, have a Yama-
ha dealer check the cooling sys-
tem.
17. Install the cowlings and panel.EAU40371
Air filter element
The air filter element should be clea-
ned or replaced at the intervals speci-
fied in the periodic maintenance and
lubrication chart. Have a Yamaha
dealer clean or replace the air filter
element.
EAU21280
Adjusting the carburetor
The carburetor is an important part of
the engine and requires very sophisti-
cated adjustment. Therefore, most
carburetor adjustments should be left
to a Yamaha dealer, who has the
necessary professional knowledge
and experience. The adjustment des-
cribed in the following section, howe-
ver, may be serviced by the owner as
part of routine maintenance.
ECA10550
The carburetor has been set and
extensively tested at the Yamaha
factory. Changing these settings
without sufficient technical know-
ledge may result in poor perfor-
mance of or damage to the engine.
NOTICE
PERIODIC MAINTENANCE AND ADJUSTMENT
6-17
6
1HD-F819D-E0 7/3/11 20:27 Página 54
2AS-F819D-E0.indd 5431/07/12 10:09

Engine overheatingEWA10400
Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.
After removing the radiator cap retaining bolt, place a thick rag, like a towel, over the radiator cap, a\
nd then
slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the his-
sing sound has stopped, press down on the cap while turning it counterclockwise, and then remove the cap.
TIP
If coolant is not available, tap water can be temporarily used instead, \
provided that it is changed to the recommended
coolant as soon as possible.
Wait until the
engine has cooled.Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.
The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.
Add coolant. (See TIP.)
Start the engine. If the engine overheats again, have a
Yamaha dealer check and repair the cooling system.
There is
leakage.
There is
no leakage.
WARNING
PERIODIC MAINTENANCE AND ADJUSTMENT
6-39
6
1HD-F819D-E0 7/3/11 20:27 Página 76
2AS-F819D-E0.indd 7631/07/12 10:09

Dimensions:Overall length:2202 mm (86.7 in)
Overall width: 689 mm (27.1 in)
Overall height: 1175 mm (46.3 in)
Seat height: 820 mm (32.3 in)
Wheelbase: 1341 mm (52.8 in)
Ground clearance: 151 mm (5.94 in)
Minimum turning radius: 2900 mm (114.2 in)
Weight:Curb weight:124 kg (273 lb)
Engine:Engine type:Liquid cooled 2-stroke
Cylinder arrangement: Single cylinder
Displacement: 49 cm
3
Bore x stroke:40.3 x 39.0 mm (1.59 x 1.54 in)
Compression ratio: 11.50 : 1
Starting system: Electric starter
Lubrication system: Wet sump
Engine oil:Type:YAMALUBE 2S or 2-stroke engine oil
(JASO FC grade) or (ISO EG-C or EG-D
grade)
Engine oil quantity:Quantity: 1.40 L (1.48 US qt, 1.23 Imp.qt)
Transmission oil:Transmission oil change quantity:0.75 L (0.79 US qt, 0.66 Im.qt)
Type: SAE10W-30 type SE motor oil
Cooling system:Coolant reservoir capacity (up to the maxi-
mum level mark):0.29 L (0.31 US qt, 0.26 Imp.qt)
Radiator capacity (including all routes): 0.70 L (0.74 US qt, 0.62 Imp.qt)
Air filter:Air filter element:Wet element
Fuel:Recommended fuel:Premium unleaded gasoline only
Fuel tank capacity: 13.8 L (3.65 US gal, 3.04 Imp.gal)
Fuel reserve amount: 2.2 L (0.58 US gal, 0.48 Imp.gal)
Carburetor:Manufacturer:DELL’ORTO
Type x quantity: PHBN 16 / DELL’ORTO x1
Spark plug(s):Manufacturer/model:NGK / BR9 ES
Spark plug gap: 0.6–0.7 mm (0.024–0.028 in)
Clutch type: Wet, multiple-disc
Transmission:Primary reduction ratio:71/20 (3.55)
Secondary reduction ratio: 60/11 (5.45)
Final drive: Chain
Transmission type: Constant mesh 6-speed
Operation: Left foot operation
Gear ratio:1st:36/12 (3.00)
2nd: 33/16 (2.062)
3rd: 29/19 (1.526)
4th: 32/24 (1.227)
5th: 25/24 (1.041)
6th: 24/25 (0.960)
Chassis:Frame type:Double cradle
SPECIFICATIONS
8-1
8
1HD-F819D-E0 7/3/11 20:27 Página 81
2AS-F819D-E0.indd 8131/07/12 10:09