engine YAMAHA VX110 2005 Manual PDF

7-17
E
–+ELEC
NOTE:
To crank the engine, connect the engine shut-
off cord (lanyard) to the engine shut-off switch,
and then press the start switch and engine
stop switch simultaneously.
4. Measure:
Rectifier/regulator output voltage
Below specification →
Replace the recti-
fier/regulator.
NOTE:
Do not use the peak voltage adapter to mea-
sure the output voltage.
Disconnect the output lead of the tester har-
ness.
Test harness (6 pins):
YB-06848
Test harness FSW-6A (6 pins):
90890-06848
Rectifier/regulator output
voltage:
Red (R) – Black (B)
r/minUnloaded
3,500
V 13.0
BATTERY
Refer to “ELECTRICAL” in Chapter 3.
FUSE
Refer to “STARTING SYSTEM”.
SPARK PLUGS
Refer to “POWER UNIT” in Chapter 3.
IGNITION SYSTEM
ProCarManuals.com

7-18
E
–+ELEC
IGNITION COIL
1. Measure:
Primary coil resistance
Out of specification →
Replace.
NOTE:
When measuring a resistance of 10 Ω
or less
using a digital tester, the correct measurement
cannot be obtained because of the tester’s
internal resistance.
Refer to “Low resistance measurement”.
Primary coil resistance:
1.19–1.61
Ω at 20 °C (68 °F)
2. Measure:
Secondary coil resistance
Out of specification →
Replace.
Secondary coil resistance:
8.5–11.5 k
Ω at 20 °C (68 °F)
ENGINE STOP SWITCH
1. Check:
Engine stop switch continuity
Out of specification →
Replace.
Engine stop switch continuity
(black coupler)
Clip PositionLead color
White Black
InstalledFree
Push
RemovedFree
Push
IGNITION SYSTEM
ProCarManuals.com

7-19
E
–+ELECIGNITION SYSTEM
ENGINE TEMPERATURE SENSOR
1. Measure:
Engine temperature sensor resistance
(at the specified temperature)
Out of specification →
Replace.
Engine temperature sensor
resistance:
20 °C (68 °F): 54.2–69.0 k
Ω
100 °C (212 °F): 3.12–3.48 k
Ω
Measurement steps:
Suspend the engine temperature sensor
in a container filled with water.
Place a thermometer in the water.
Slowly heat the water.
Measure the resistance when the speci-
fied temperature is reached.
SENSOR ASSEMBLY
1. Check:
Intake air temperature sensor
Out of specification →
Replace the sen-
sor assembly.
Checking steps:
Measure the ambient temperature.
Connect a computer to the watercraft and
use the Yamaha Diagnostic System to
display the intake air temperature.
If the ambient temperature and the dis-
played intake air temperature differ by
more than ±
5 °C (±
9 °F), replace the
sensor assembly.
ProCarManuals.com

7-20
E
–+ELECIGNITION SYSTEM
THERMOSWITCH (ENGINE)
1. Check:
Thermoswitch (engine) continuity
(at the specified temperature)
Out of specification →
Replace.
1 No continuity
È Temperature
2 Continuity
É Time
NOTE:
The thermoswitch (engine) connector is blue.
Thermoswitch (engine) continuity
temperature:
a 84–90 °C (183–194 °F)
b 70–84 °C (158–183 °F)
Checking steps:
Suspend the thermoswitch (engine) in a
container filled with water.
Place a thermometer in the water.
Slowly heat the water.
Measure the continuity when the speci-
fied temperature is reached.
ProCarManuals.com

7-31
E
–+ELECFUEL CONTROL SYSTEM
FUEL CONTROL SYSTEM
WIRING DIAGRAM
10A
10A
3A
30A20A
RR
BBR
B/W
B/O
B/O
B/R
P/R
P/R
P/W
P/W
B/O
L/B
B/WB/R
B/O
P/RP/W
G
O
W
O
OLG
WR/YP/GY/G
B
OL
PB
Pu/RPu/B
Pu/GPu/Y
P/W
R/Y
W/B
Y/WL/R
B
BBP
P
P
BBP
R/Y
B/OL/BB/OL/B
P/G
P/W
B/O
B/O
B/YB/YR/Y
R/Y
R/Y
R/YPu/G
Pu/Y
Pu/B
Pu/RR/Y
R/Y
R/Y
R/Y
R/YY/W
Y/GL/R
O
P
P
O
R
R
L
R
R
B
BLBL
B
B/GPPB
W/BR/YB RW
9 87
E
E E E FGH I3
4
56 2 1
0
A
B
C
D J
K
1Battery
2Fuse (30 A)
3Fuse (20 A)
4Fuse (10 A)
5Fuse (10 A)
6Starter relay
7Main and fuel pump relay
8Electronic control throttle valve
relay9Slant detection switch
0Sensor assembly
(intake air pressure and intake
air temperature)
AEngine temperature sensor
BThermoswitch (engine)
CThermoswitch (exhaust)
DOil pressure switch
EFuel injectorFECM
GThrottle body assembly
HAccelerator position sensor
IElectric fuel pump
JFuel sender
KMultifunction meter
ProCarManuals.com

7-34
E
–+ELECFUEL CONTROL SYSTEM
FUEL INJECTOR
Refer to “FUEL INJECTION SYSTEM”
in Chapter 4.
MAIN AND FUEL PUMP RELAY
Refer to “IGNITION SYSTEM”.
OIL PRESSURE SWITCH
Refer to “INDICATION SYSTEM”.
THERMOSWITCH (ENGINE)
Refer to “IGNITION SYSTEM”.
THERMOSWITCH (EXHAUST)
Refer to “IGNITION SYSTEM”.
SLANT DETECTION SWITCH
Refer to “IGNITION SYSTEM”.
REMOTE CONTROL UNIT
(DELUXE MODEL ONLY)
Refer to “REMOTE CONTROL SYS-
TEM (DELUXE MODEL ONLY)”.
THROTTLE POSITION SENSOR
Refer to “IGNITION SYSTEM”.
ACCELERATOR POSITION SENSOR
Refer to “IGNITION SYSTEM”.
ProCarManuals.com

7-35
E
–+ELECSTARTING SYSTEM
STARTING SYSTEM
WIRING DIAGRAM
WBrBRFREE
PUSHBWFREE
PUSH
Br BrFREE
PUSH
BW
W
BrBrBrBrR
RB/O
10A
10A
3A
30A20A
RR
B
BBR
BBr
BBr
B
B/W
B/O
B/O
B/R
P/R
P/R
P/W
P/W
B/O
B/WB/R
B/O
P/RP/W
W
W
WL
RY
G
O
W
O
OLG
W
Y
W
G/O
R/YY/G
BOL
BW
R/Y
Y/WL/R
B
B
G/OB/OG/OR/YB/O
R/Y
R/Y
R/Y
Y/W
Y/GL/R
Y
O
O
R
RL
R
B
BLBL
Y BrL R B
Br W
09
B
C DEF G
5 4
6
78 3 I
HJ1
2
A
1Battery
2Starter motor
3Fuse (30 A)
4Fuse (20 A)
5Fuse (3 A)
6Fuse (10 A)
7Fuse (10 A)
8Starter relay
9Main and fuel pump relay0Electronic control throttle valve
relay
ACam position sensor
BRemote control unit
CAntenna
DECM
EThrottle body assembly
FAccelerator position sensor
GElectric fuel pumpHStart switch
IEngine stop switch
JEngine shut-off switch
ProCarManuals.com

7-47
E
–+ELECOFF THROTTLE STEERING SYSTEM
STEERING SENSOR
1. Check:
Steering sensor
Malfunction → Replace the steering
sensor.
Checking steps:
Turn the handlebar all the way to the left
or right, and then release it.
Install a plastic tie 1 loosely around the
center of the handlebar grip as shown.
Hook a spring gauge 2 onto the plastic
tie.
Hold the spring gauge at a 90° angle
from the handlebar, and then pull the
spring gauge with a force of 10 kgf
(22 lb).
When handlebar
pulledWhen handlebar
not pulled
ON OFF
Check that the following is displayed in
the “Engine Monitor” window of the
Yamaha Diagnostic System.
Use the same procedure to check that
the steering sensor operates correctly
when the handlebar is turned to both the
left and right. Replace the steering sen-
sor if it is a malfunction.
1
2
ECM
Refer to “IGNITION SYSTEM”.
PICKUP COIL
Refer to “IGNITION SYSTEM”.
THROTTLE POSITION SENSOR
Refer to “IGNITION SYSTEM”.
ACCELERATOR POSITION SENSOR
Refer to “IGNITION SYSTEM”.
ProCarManuals.com

7-48
E
–+ELECINDICATION SYSTEM
INDICATION SYSTEM
WIRING DIAGRAM
10A
10A
3A
30A20A
RR
BBR
BBr
BBr
B/OW/B
B/O
B/O
WR
Y
G
O
BW
Y
W
G/OW/B
Y/GR/Y
B
PB
Pu/RPu/B
Pu/GPu/Y
P/W
B/G
R/Y
W/B
B/Y
Y/WL/R
B/RB/W
B
B
BBP
P
PBBP
R/Y
B/G
G/OB/OG/O
P/W
B/OB/YB/YR/Y
R/Y
R/Y
B/LL/YL/B
R/YPu/G
Pu/Y
Pu/B
Pu/RR/Y
R/Y
R/Y
R/YB/YR/Y
R/Y
B/O
B/RR/Y
R/Y
R/YY/W
Y/GL/R
Y
P
P
O
O
R
R
R
B
G
BR
Y
B/YR/W
BRW
P
PB
B/LL/R
L/RL/B
B/WR
BW/BR/YL/RL/YL/B Gy B/G
YB/YR/Y
98
A
A A
A
G
G GG
H IJ K4 3
5
67 2 1
0
0 0
0
B
C
D
E
F LM
N
1Battery
2Fuse (30 A)
3Fuse (20 A)
4Fuse (3 A)
5Fuse (10 A)
6Fuse (10 A)
7Starter relay
8Main and fuel pump relay9Electronic control throttle valve
relay
0Ignition coil
ASpark plug
BCam position sensor
CEngine temperature sensor
DThermoswitch (engine)
EThermoswitch (exhaust)
FOil pressure switchGFuel injector
HRemote control unit
(Deluxe model only)
IECM
JPickup coil
KBuzzer
LFuel sender
MSpeed sensor
NMultifunction meter
ProCarManuals.com

7-50
E
–+ELECINDICATION SYSTEM
FUSE
Refer to “STARTING SYSTEM”.
BATTERY
Refer to “ELECTRICAL” in Chapter 3.
MAIN AND FUEL PUMP RELAY
Refer to “IGNITION SYSTEM”.
ECM
Refer to “IGNITION SYSTEM”.
ENGINE TEMPERATURE SENSOR
Refer to “IGNITION SYSTEM”.
THERMOSWITCH (ENGINE)
Refer to “IGNITION SYSTEM”.
THERMOSWITCH (EXHAUST)
Refer to “IGNITION SYSTEM”.
REMOTE CONTROL UNIT
(DELUXE MODEL ONLY)
Refer to “REMOTE CONTROL SYS-
TEM (DELUXE MODEL ONLY)”.
BUZZER
1. Check:
Buzzer
Buzzer does not sound → Replace.
Checking steps:
Connect the battery (12 V) to the buzzer
coupler as shown.
Battery positive terminal →
Red (R) terminal 1
Battery negative terminal →
Black (B) terminal 2
ProCarManuals.com