check engine YAMAHA XVS125 2002 User Guide

6-9
PERIODIC MAINTENANCE AND MINOR REPAIR
6
NOTE:
If a torque wrench is not available
when installing a spark plug, a good
estimate of the correct torque is
1/4–1/2 turn past finger tight.
However, the spark plug should be
tightened to the specified torque as
soon as possible.4. Install the spark plug cap.
EAU04433
Engine oil and oil filter
element
Engine oil and oil filter element
The engine oil level should be
checked before each ride. In addition,
the oil must be changed and the oil
filter element replaced at the intervals
specified in the periodic maintenance
and lubrication chart.
To check the engine oil level
1. Place the motorcycle on a level
surface and hold it in an upright
position.NOTE:
Make sure that the motorcycle is
positioned straight up when checking
the oil level. A slight tilt to the side
can result in a false reading.2. Start the engine, warm it up for
several minutes, and then turn it
off.3. Wait a few minutes until the oil
settles, and then check the oil
level through the check window
located at the bottom-right side
of the crankcase.
NOTE:
The engine oil should be between the
minimum and maximum level marks.4. If the engine oil is below the min-
imum level mark, add sufficient
oil of the recommended type to
raise it to the correct level.
2
1
3
1. Oil level check window
2. Maximum level mark
3. Minimum level mark
Tightening torque:
Spark plug:
12.5 Nm (1.25 m0kgf)
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 39

6-12
PERIODIC MAINTENANCE AND MINOR REPAIR
69. Start the engine, and then let it
idle for several minutes while
checking it for oil leakage. If oil is
leaking, immediately turn the
engine off and check for the
cause.
10. Turn the engine off, and then
check the oil level and correct it if
necessary.
EAU03330
Cleaning the air filter
elementThe air filter element should be
cleaned at the intervals specified in
the periodic maintenance and lubrica-
tion chart. Clean the air filter element
more frequently if you are riding in
unusually wet or dusty areas.
1. Remove the air filter case by
removing the bolts and loosening
the clamp screw.2. Remove the air filter case cover
by removing the screws.
1
2
1
1
1. Bolt (×2)
2. Clamp screw1. Screw (×5)
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 42

6-14
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU00629
Adjusting the carburetor
Carburetor, adjusting
The carburetor is an important part of
the engine and requires very sophisti-
cated adjustment. Therefore, most
carburetor adjustments should be left
to a Yamaha dealer, who has the
necessary professional knowledge
and experience. The adjustment
described in the following section,
however, may be serviced by the
owner as part of routine mainte-
nance.
EC000094
cCThe carburetor has been set and
extensively tested at the Yamaha
factory. Changing these settings
without sufficient technical knowl-
edge may result in poor perfor-
mance of or damage to the engine.
EAU01168
Adjusting the engine idling
speed
Engine idling speed
The engine idling speed must be
checked and, if necessary, adjusted
as follows at the intervals specified in
the periodic maintenance and lubrica-
tion chart.NOTE:
A diagnostic tachometer is needed to
make this adjustment.1. Attach the tachometer to the
spark plug lead.
2. Start the engine and warm it up
for several minutes at 1,000–
2,000 r/min while occasionally
revving it to 4,000–5,000 r/min.NOTE:
The engine is warm when it quickly
responds to the throttle.
3. Check the engine idling speed
and, if necessary, adjust it to
specification by turning the throt-
tle stop screw. To increase the
engine idling speed, turn the
screw in direction a. To
decrease the engine idling speed,
turn the screw in direction b.NOTE:
If the specified idling speed cannot
be obtained as described above,
have a Yamaha dealer make the
adjustment.
1b
a
1. Throttle stop screw
Engine idling speed:
1,250–1,450 r/min
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 44

6-15
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU00635
Adjusting the throttle cable
free play
Throttle cable free play, adjusting
The throttle cable free play should
measure 3–5 mm at the throttle grip.
Periodically check the throttle cable
free play and, if necessary, have a
Yamaha dealer adjust it.
EAU00637
Adjusting the valve
clearance
Valve clearance, adjusting
The valve clearance changes with
use, resulting in improper air-fuel mix-
ture and/or engine noise. To prevent
this from occurring, the valve clear-
ance must be adjusted by a Yamaha
dealer at the intervals specified in the
periodic maintenance and lubrication
chart.
EAU04427
Tires
Tires
To maximize the performance, dura-
bility, and safe operation of your
motorcycle, note the following points
regarding the specified tires.
Tire air pressure
The tire air pressure should be
checked and, if necessary, adjusted
before each ride.
EW000082
w8The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the tempera-
ture of the tires equals the
ambient temperature).
8The tire air pressure must be
adjusted in accordance with
the riding speed and with the
total weight of rider, passen-
ger, cargo, and accessories
approved for this model.
a
a. Throttle cable free play
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 45

6-26
PERIODIC MAINTENANCE AND MINOR REPAIR
62. To tighten the drive chain, turn
the adjusting nut at each end of
the swingarm in direction a. To
loosen the drive chain, turn the
adjusting nut at each end of the
swingarm in direction b, and
then push the rear wheel for-
ward.
NOTE:
Using the alignment marks on each
side of the swingarm, make sure that
both adjusting nuts are in the same
position for proper wheel alignment.
EC000096
cCImproper drive chain slack will
overload the engine as well as
other vital parts of the motorcycle
and can lead to chain slippage or
breakage. To prevent this from
occurring, keep the drive chain
slack within the specified limits.3. Tighten both locknuts, and then
tighten the axle nut to the speci-
fied torque.
4. Adjust the brake pedal free play.
(See page 6-21 for brake pedal
free play adjustment proce-
dures.)
EW000103
wAfter adjusting the brake pedal
free play, check the operation of
the brake light.
1
3
1
2
ba
1. Axle nut 1. Drive chain adjusting nut
2. Alignment marks
3. Locknut
Tightening torque:
Axle nut:
104 Nm (10.4 m0kgf)
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 56

6-27
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU03006
Lubricating the drive chain
Drive chain, lubricating
The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly
wear out, especially when riding in
dusty or wet areas. Service the drive
chain as follows.
EC000097
cCThe drive chain must be lubricated
after washing the motorcycle or
riding in the rain.1. Clean the drive chain with
kerosene and a small soft brush.
ECA00053
cCTo prevent damaging the O-rings,
do not clean the drive chain with
steam cleaners, high-pressure
washers or inappropriate solvents.
2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive
chain with a special O-ring chain
lubricant.
ECA00052
cCDo not use engine oil or any other
lubricants for the drive chain, as
they may contain substances that
could damage the O-rings.
EAU02962
Checking and lubricating the
cables
Cables, checking and lubricating
The operation of all control cables
and the condition of the cables
should be checked before each ride,
and the cables and cable ends
should be lubricated if necessary. If
a cable is damaged or does not move
smoothly, have a Yamaha dealer
check or replace it.
Recommended lubricant:
Engine oil
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 57

6-30
PERIODIC MAINTENANCE AND MINOR REPAIR
6To check the operation
1. Place the motorcycle on a level
surface and hold it in an upright
position.
2. While applying the front brake,
push down hard on the handle-
bars several times to check if the
front fork compresses and
rebounds smoothly.
EC000098
cCIf any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or
repair it.
EAU00794
Checking the steering
Steering, checking
Worn or loose steering bearings may
cause danger. Therefore, the opera-
tion of the steering must be checked
as follows at the intervals specified in
the periodic maintenance and lubrica-
tion chart.
1. Place a stand under the engine
to raise the front wheel off the
ground.
EW000115
wSecurely support the motorcycle
so that there is no danger of it
falling over.
2. Hold the lower ends of the front
fork legs and try to move them
forward and backward. If any
free play can be felt, have a
Yamaha dealer check or repair
the steering.
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 60

6-37
PERIODIC MAINTENANCE AND MINOR REPAIR
6 2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.
EC000108
cCDo not overtighten the screws,
otherwise the lens may break.
EAU01579
Supporting the motorcycle
Supporting the motorcycle
Since this model is not equipped with
a centerstand, follow these precau-
tions when removing the front and
rear wheel or performing other main-
tenance requiring the motorcycle to
stand upright. Check that the motor-
cycle is in a stable and level position
before starting any maintenance. A
strong wooden box can be placed
under the engine for added stability.
To service the front wheel
1. Stabilize the rear of the motorcy-
cle by using a motorcycle stand
or, if an additional motorcycle
stand is not available, by placing
a jack under the frame in front of
the rear wheel.
2. Raise the front wheel off the
ground by using a motorcycle
stand.
1
1. Bulb
EAU01623
Replacing the tail/brake light
bulb
Tail/brake light bulb, replacing
1. Remove the tail/brake light lens
by removing the screws.
2
1
1. Lens
2 Screw (×2)
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 67

6-42
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU01297
Troubleshooting chart
EW000125
wKeep away open flames and do not smoke while checking or working on the fuel system.1. Fuel
2. Compression
3. Ignition
4. Battery
Remove the spark
There is compression.
There is no compression.
Check the ignition.Have a Yamaha dealer check the vehicle.
Wet
DryWipe off with a dry cloth and correct the spark
Have a Yamaha dealer check the vehicle.
The engine turns
The engine turnsThe battery is good.
Check the battely lead connections,
Check the fuel level
There is enough fuel.
There is no fuel.
Check the compression.
in the fuel tank.
the electrodes. plugs and check
over quickly.
over slowly. and charge the battery if necessary.Open the throttle halfway and
The engine does not start.Check the battery.operate the electric starter. plug gaps, or replace the spark plugs.
Supply fuel.
The engine does not start. Check the compression.
Operate the electric
starter. Operate the electric starter.
The engine does not start.
Have a Yamaha dealer
check the vehicle.
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 72