erg ASTON MARTIN V8 VANTAGE 2010 Workshop Manual

Vehicle Recovery
0-0-10 Workshop Manual Issue 5, January 2010
Vehicle Recovery
General
Preferred method of vehicle recovery is by flat bed
transporter.
The towing eye is primarily for emergency use when towing
for short distances, e.g. removing vehicle if it is causing an
obstruction or winching vehicl e onto a flatbed transporter.
If moving this vehicle in such a situation, install the towing
eye to the bracket in the lower grille aperture.
Transporting
If vehicle is to be transported on a trailer or flat bed
transporter the handbrake must be applied and the road
wheels must be chocked.
Suspended Towing
Take care when using 'spectacle frame' type towing
equipment that the towing device is well clear of front or
rear apron. Body damage may occur if vehicle passes over
uneven road surfaces.
Front Suspended Tow
1. Remove the ignition key from the ignition.
2. Raise the vehicle using a ‘spectacle frame’ type lifting device with a cradle positioned under each front wheel
as indicated below.
Rear Suspended Tow
1. Set the steering in the ‘straight ahead’ position.
Remove the ignition key from the ignition. Ensure the
steering is locked in the straight ahead position.
2. Raise the vehicle using a 'spectacle frame' style lifting device where a cradle is positioned under each rear
wheel as indicated below.
Adhere to Towing Regulations
In certain countries the regi stration number of towing
vehicle and an ‘ON TOW’ sign or warning triangle must be
displayed in a prominent position at the rear of vehicle being
towed.
To w i n g b y A n o t h e r V e h i c l e
This vehicle may be towed short distances by another
vehicle provided that a speed of 48 km/h (30 mph) is not
exceeded. Ensure the towed vehicle gear selection is in
‘Neutral’ with ignition key turned to position ‘II’ to release
steering lock and to render hor n, indicators and brake lights
operational.
Caution
Take care to protect the paint work when installing the towing eye. Ensure the towing eye is tight.
Caution
Do not tow with ‘sling’ type equipment as this
could result in damage to the bodywork.
WAR NI NG
WHEN THE ENGINE IS NOT RUNNING, THE STEERING WILL NO LONGER BE POWER-ASSISTED AND THE
BRAKE BOOSTER WILL BECOME INEFFECTIVE AFTER A FEW APPLICATIONS OF TH E BRAKES. BE PREPARED
FOR RELATIVELY HEAVY STEERING AND THE NEED
FOR GREATLY INCREASED BRAKE PEDAL PRESSURE.

1-1-2 Workshop Manual Issue 5, January 2010
RH/LH Seat Switchpack Assembly - Renew...........7-13
Lumbar Pump for the Front Seat (From 08MY)
- Remove and Install.............................................7-13
Lumbar Valve for the Front Seat (From 08MY)
- Remove and Install.............................................7-14
Lumbar Bladder for the Front Seat (From 08MY)
- Remove and Install.............................................7-14
Glass, Frame and Mechanism (01.11) .................. 1-8-1 Description .............................................................8-1 Frameless doors......................................................8-1
Specifications .........................................................8-1
Maintenance ...........................................................8-1 Glass Regulator - Renew .........................................8-1
RH/LH Door Glass - Renew ....................................8-2
Door Glass - Adjust/Reset .......................................8-3
Front Windshield - Renew ......................................8-3
Rear Windshield - Renew .......................................8-4
Quarter Window Glass - Renew .............................8-6
Passenger Window Lift Switch - Renew ..................8-6
Driver Window Lift Switch - Renew........................8-7
Instrument Panel (IP) (01.12)................................ 1-9-1 Specifications ..........................................................9-1
Maintenance ...........................................................9-1 Instrument Panel - Renew ......................................9-1
Airbag Panel and Door Assembly - Renew ..............9-6
Glovebox Assembly - Renew ..................................9-6
Instrument Centre Panel Asse mbly - Renew............9-7
Knee Protector - Renew .........................................9-7
Instrument Panel As sembly - Renew .......................9-7
Cluster Bezel Panel - Renew .................................9-10
Driver Panel Assembly - Renew ............................9-10
Instrument Panel Bezel A ssembly (With Sat. Nav.)
- Renew ...............................................................9-11
Instrument Panel Bezel Assembly
(Without Sat. Nav.) - Renew .................................9-11
Rear Console Panel Assembly - Renew .................9-12
Armrest Pad Assembly - Renew ............................9-13
Console Panel Assembly - Renew .........................9-13
RH/LH Rear Console Pa nel Assembly - Renew
(Roadster Only) ....................................................9-13
Centre Console Panel - Remove and Install
(Coupe Only) .......................................................9-15
Centre Console Panel - Remove and Install
(Roadster Only) ....................................................9-19
RH/LH Lower Quarter Panel Assembly - Renew
(Roadster Only) ....................................................9-29
Handles and Lock Mechanisms (01.14) .............. 1-10-1 Description ...........................................................10-1 Vehicle Key/Remote Transmitter...........................10-1
Central Locking System ........................................10-1
Remote Transmitter ..............................................10-1
Fuel Filler Assembly ..............................................10-1
Boot Emergency Release ....... ...............................10-1
Specifications ........................................................10-2
Maintenance .........................................................10-2 Ignition Cylinder Lock - Re new.............................10-2
RH/LH Front Door Latch As sembly - Renew .........10-2
Bonnet Latch Assembly - Renew...........................10-3
Hood Release Cable Assembly - Renew (Roadster Only) .................................................... 10-3
Bonnet Secondary Latch Asse
mbly - Renew ......... 10-4
Tailgate Latch and Cable Assembly - Renew ......... 10-4
Fuel Filler Actuator Assembly - Renew
(Roadster Only) .................................................... 10-4
Fuel Filler Release Cable - Renew (Roadster Only) 10-5
Fuel Flap Release Switch - Renew ........................ 10-6
RH/LH Tonneau Latch Motor - Renew
(Roadster Only) .................................................... 10-7
RH/LH Tonneau Latch - Renew (Roadster Only) ... 10-7
RH/LH Tonneau Cover Striker Assembly
- Renew (Roadster Only) ...................................... 10-8
Tailgate Latch Assembly-Renew (Roadster Only) ... 10-8
Wipers and Washer System (01.16) ....................1-11-1 Headlamp Washing .............................................. 11-1
Specifications ........................................................ 11-2
Maintenance ......................................................... 11-2 Windscreen Wiper Motor As sembly - Renew ....... 11-2
Wiper Linkage Assembly - Renew ........................ 11-2
Windshield Wash Tube - Renew .......................... 11-2
Windscreen Reservoir and Motor Assembly
- Remove and Install ............................................ 11-3
Low Level Water Sensor - Remove and Install ...... 11-4
Headlamp Wash Motor and Pump Assembly
- Renew ............................................................... 11-5
Headlamp Wash Tube Assembly - Renew ............ 11-5
Washer Fluid Reservoir - Renew........................... 11-6
Convertible Roof and Roof Opening Subsystem
(01.17)..................................................................1-12-1 System Description .............................................. 12-1
Maintenance ......................................................... 12-2 Hood Assembly-Renew ........................................ 12-2
Canopy Cover - Renew ........................................ 12-5
Header Latch Motor - Renew ............................... 12-9
Hydraulic Main Actuator Cy linder - Renew .......... 12-9
Hydraulic Tensrod Cylinder - Renew .................. 12-10
Hydraulic Tonneau Cylinder - Renew................. 12-11
Convertible Top ECU - Renew ........................... 12-13
Hydraulic Pump - Renew ................................... 12-13
Hydraulic Lock Valve - Renew............................ 12-16
RH/LH Front Cantrail Seal - Spare Part
- Renew ............................................................. 12-18
RH/LH Front Cantrail Seal Spare Part Kit
- Renew ............................................................. 12-18
RH/LH Middle Cantrail Seal Spare Part
- Renew ............................................................. 12-18
RH/LH Middle Cantrail Seal Spare Part Kit
- Renew ............................................................. 12-19
Rear Seal Spare Part Assembly Kit - Renew ......... 12-20
LH Fully Automatic Latching Kit - Renew............ 12-21
RH Fully Automatic Latching Kit - Renew ........... 12-22
Convertible Roof Hydraulic Pump
- Check Fluid Level ............................................ 12-23
Cantrail Cover Trim - Renew .............................. 12-25
B-Post Trim Cover - Renew ................................ 12-25
Tonneau Cover - Renew .................................... 12-27
LH Front Main Hydraulic Cylinder Pipe
- Renew ............................................................. 12-29
LH Rear Main Hydraulic Cylinder Pipe

Issue 5, January 2010 Workshop Manual 1-1-3
- Renew ............................................................. 12-33
RH Front Main Hydraulic Cylinder Pipe
- Renew ............................................................. 12-37
RH Rear Main Hydraulic Cylinder Pipe
- Renew ............................................................. 12-40
LH Front Hydraulic Cylinder Pipe - Renew........ 12-43
LH Rear Hydraulic Cylinder Pipe - Renew.......... 12-46
RH Front Hydraulic Cylinder Pipe - Renew ........ 12-50
RH Rear Hydraulic Cylinder Pipe - Renew ......... 12-53
RH/LH Rear Hydraulic Tonneau Cylinder Pipe
- Renew ............................................................. 12-56
LH/RH Front Hydraulic Tonneau Cylinder Pipe
- Renew ............................................................. 12-60
Hydraulic Cylinder Valve to Pump Pipe
- Renew ............................................................. 12-63
Wind Deflector - Renew .................................... 12-66
Tonneau Well Liner - Renew . ............................ 12-67
RH/LH Flex Shaft - Renew ................................. 12-69
Bumpers (01.19) .................................................. 1-13-1 Front Bumper ....................................................... 13-1
Rear Bumper......................................................... 13-1
Specifications........................................................ 13-2
Maintenance ......................................................... 13-2Front Bumper Cover - Renew .............................. 13-2
Rear Bumper Cover - Renew................................ 13-3
Restraining Devices (01.20)................................. 1-14-1 Seat Belts .............................................................. 14-1Emergency Locking Retractor (ELR) ...................... 14-2
Airbag System ....................................................... 14-3
Maintenance ......................................................... 14-4 Driver’s Airbag Module - Renew .......................... 14-4
LH Front Seat Belt - Renew .................................. 14-4
RH Front Seat Belt - Renew.................................. 14-5
Passenger Airbag - Renew .................................... 14-6
ARS Side Impact Sensor Assembly - B Pillar
- Renew ............................................................... 14-6
Side Impact Door ARS Sensor Assembly
- Renew ............................................................... 14-6
Front Impact Sensor Assembly - Renew ................ 14-7
Occupant Restraint Control Module Assembly
- Renew ............................................................... 14-7
RH/LH Roll Over Protection System - Renew ....... 14-8

Handles and Lock Mechanisms (01.14)
Body System (01.00)
May 2007 Workshop Manual 1-10-1
Body System (01.00)
Handles and Lock Mechanisms (01.14)
Description
The vehicle key operates the
ignition and the door lock, the
remote transmitter operates the
central locking and alarm systems.
Do not leave them in the vehicle .
Central Locking System
The Central Locking system consists of lock actuators in both
doors, the boot and the fuel flap. Central locking control is
through the door modules.
Each lock actuator incorporates a microswitch which signals
a change of state when any motor runs to drive the actuator.
The microswitches are of the change over type and provide
an earth for lock/unlock signals to the door module.
The boot will remain locked or will be unlocked
simultaneously with the doors dependant on the boot lock
position. The boot lock can be enabled at any time using the
remote transmitter irrespective of the Central Locking status.
Remote Transmitter
The remote control system consists of a transmitter and an
antenna (radio frequency system). The remote control
transmitter for the radio frequency system will operate
without the transmitter being directed at the vehicle. The
normal range between the transmitter and the antenna is up
to 5 meters. Before the remote control system can be used,
each transmitter must be initialized to the vehicle. A
maximum number of four transmitters can be initialized to
any vehicle. All remote transmitters must be initialized at the
same time.The keyless entry / remote operated locks will not
operate when the ignition key is in the ignition switch.
(A) Lock - One step vehicle
locking and alarm enable
.
(B) Un-lock - One step vehicle
unlocking or two step vehicle
unlocking and alarm disable.
(C) Boot Open - Press to enable
the boot catch.
(D) Panic Alarm - Activates / deactivates the panic alarm.
(E) Approach Light - Activates the front and rear side lights.
Fuel Filler Assembly
Boot Emergency Release
The boot can be opened from in side the boot by pulling the
luminous emergency release handle.
The vehicle will deadlock after 25 seconds.

Handles and Lock Mechanisms (01.14)
Body System (01.00)
May 2007 Workshop Manual 1-10-7
RH/LH Tonneau Latch Motor - Renew
(Roadster Only)
Removal
1. Remove wind deflector (see Workshop Manual procedure 01.17.DA Wind Deflector - Renew).
2. Release 2 clips securing harness to latch motor bracket.
3. Remove 4 bolts securing latch motor bracket to body (see Figure 1).
4. Disconnect latch motor multiplug.
5. Release cable from latch motor.
6. Remove 2 screws securing latch motor to bracket and remove.
Installation
1. Install latch motor and secure to bracket with screws.
2. Secure cable to latch motor.
3. Connect latch motor multiplug.
4. Secure latch motor bracket to body with screws.
5. Secure harness to latch motor bracket.
6. Install wind deflector (see Workshop Manual procedure 01.17.DA Wind Deflector - Renew).
RH/LH Tonneau Latch - Renew (Roadster
Only)
Removal
1. Remove wind deflector (see Workshop Manual procedure 01.17.DA Wind Deflector - Renew).
2. Release tonneau latch multiplug from body and disconnect.
3. Unclip emergency pull string from tonneau latch (see Figure 1).
4. Mark position of tonneau latch.
5. Remove 2 bolts securing tonneau latch to bracket.
6. Unclip inner release cable from tonneau latch.
7. Unclip outer release cable from tonneau latch, remove latch.
Installation
1. Install tonneau latch and secure outer release cable.
2. Secure inner release cable to tonneau latch.
3. Align tonneau latch and secure with bolts
4. Secure pull string to tonneau latch.
5. Connect tonneau latch mult iplug and secure to body.
6. Install wind deflector (see Workshop Manual procedure
01.17.DA Wind Deflector - Renew).
Repair Operation Time (ROT)
Repair Operation Time (ROT)
Figure 1

Restraining Devices (01.20)
Body System (01.00)1-14-2 Workshop Manual May 2007
mounted onto a spindle (torsion bar) which once the sensor
has locked the retractor reel and a predetermined load is
applied, twists and allows additional webbing into the
system. The deceleration force required to initiate this
sequence is approximately th e same as that required to
initiate airbag deployment. The torsion bar load limiting
device will only react if the safety belt is in use at the time of
the impact.
Emergency Locking Retractor (ELR)
The retractors in all seat posi tions feature ELR. During any
period of sudden deceleration, or under lateral load when
cornering at speed, a sensor weight within the safety belt
retractor moves a locking pawl against the teeth on the
retractor reel, which then locks the retractor preventing any
further release of webbing. As soon as the load applied onto
the retractor through the safety belt webbing is removed the
locking pawl releases the retractor reel and normal
movement is returned to the retractor.
Automatic Locking Retractor (ALR)
Automatic locking retractors (ALR) are installed to all
passenger seat positions.
The safety belt webbing on these are clearly marked to show
their operating feature. To initiate the ALR system, fasten the
safety belt into it’s buckle and pull all of the webbing from
the retractor, as the safety belt is released the retractor locks
allowing travel in only one plane thus producing a fixed
length restraint and preventing the safety belt from
introducing slack, making any child seat it may be restraining
secure. The ALR system of the retractor is disengaged by
releasing the safety belt and allowing the safety belt to fully
retract onto the reel. Caution
It should be considered th at during any event that
utilizes the full capability of the safety belts, the
webbing may have been elongated and the torsion bar may have twisted. For this reason, if a vehicle is
involved in an accident which results in the deployment of the airbag(s), all the safety belts that were in use at
the time of the accident MUST be renewed.

Road Wheels and Tyres (04.04)
Suspension (04.00)4-4-10 Workshop Manual May 2007
Display Unit
The display unit provides additional features when correctly
connected to a previously installed ‘Smartire’ system. The
display unit connects directly to the front of the basic
‘Smartire’ receiver and is powered from the vehicle circuits.
The display will be fully illu minated during use but will go
into ‘Energy Saver’ mode when no activity is detected.
Display Panel
Connection and Normal Operation
1. Remove the front bezel of the Pressure Sensor Receiver. Install the extension lead to the display unit and to the
receiver module. Turn on the ignition.
All icons will illuminate briefly and then extinguish
leaving only the vehicle outline.
2. When tyre pressure data is received, (drive the vehicle
or spin the road wheels), all the road wheel icons will
appear. Press the Tyre icon to access the recorded data
for each of the four road wheels.
3. Press the Mode button to scroll through the pressure, temperature and pressure deviation readings for the
selected tyre. 4. If any tyre pressure sensor is defective, the display will
show three dashes to indicate the absence of data for
that tyre.
5. To return to normal mode, press the SET button.
System Programming
The system may be programmed by the user on three
different levels. Enter Progra mming Mode by pressing the
‘Set’ button:
• 2 seconds to enter level 1
• 5 seconds to enter level 2
• 10 seconds to enter level 3
The following parameters ma y be set in each level:
Level 1 Programming
Cold inflation pressure
1. Press ‘Set’ for 2 seconds to enter level 1 programming .
2. Press ‘Tyre’ to select the front or rear axle. Front or rear
tyres will be highlighted.
3. Press ‘Mode’ to show the current value. Press ‘Tyre’ to increase or ‘Mode’ to decrease the current value.
4. Press ‘Set’ to save the new values.
5. Repeat steps 2 - 4 to set the cold inflation pressure for other the axle.
Programmed wheel position No data
Data received
Alarm light Low pressure warning
Alert indicatorLearn mode MODE button
Set button
Tyre rotation program
Cold pressure program
Programming mode
Towing vehicle indicator
Numerical display
Units of pressure or temperature TYRE button
36-5-038
36-5-039
Level 1
• Cold Pressure
• Tyre Rotation
• Low Pressure Warning
• Pressure Deviation
• High Temperature Alert
•Units Selection
Level 2 •Slope
• Learn Transmitter ID
Level 3 • Low Pressure Alert
PSI
36-5-045

Version 6, March 2010 Workshop Manual 6-3-1
Brake System (06.00)
Contents
Front Disc Brake (06.03)........................................ 6-3-2Description ............................................................. 3-2
Specifications.......................................................... 3-2
Maintenance ........................................................... 3-3Front Brake Disc Set - Renew ................................. 3-3
Front Caliper-Renew .............................................. 3-4
Front Pad Kit - Renew ............................................ 3-5
Front Brake Hose Assembly - Renew ...................... 3-5
Rear Disc Brakes (06.04) ....................................... 6-4-1 Description ............................................................. 4-1
Specifications.......................................................... 4-1
Maintenance ........................................................... 4-2Rear Brake Disc Set-Renew .................................... 4-2
RH/LH Rear Caliper-Renew ................................... 4-2
Rear Pad Kit-Renew ............................................... 4-3
Rear Brake Hose Assembly-Renew ......................... 4-4
Hand Brake (06.05) ................ ............................... 6-5-1
Description ............................................................. 5-1
Specifications.......................................................... 5-1
Maintenance ........................................................... 5-2 RH/LH Handbrake Caliper-Re new ......................... 5-2
Handbrake Lever Assembly-Renew ........................ 5-2
Handbrake Pad Set-Renew .................................... 5-2
Handbrake Cable Assembly-Adjust......................... 5-3
Handbrake Cable Assembly-Vehicle Set-Renew ..... 5-3
Brake Actuation System (06.06)............................. 6-6-1 Description ............................................................. 6-1
Tandem Master Cylinder ........................................ 6-1
Specifications.......................................................... 6-1
Maintenance ........................................................... 6-2Pedal Box Assembly - Renew ................................. 6-2
Installation ............................................................. 6-2
RHD-Brake Master Cylinder Assembly-Renew........ 6-2
LHD-Brake Master Cylinder Assembly-Renew ........ 6-3
Clutch Master Cylinder Assembly-Renew ............... 6-3
RH/LH Front Caliper Hose Assembly-Renew .......... 6-4
RH/LH Rear Brake Caliper Tube Assembly-Renew . 6-5
Brake Master Cylinder to Modulator Secondary
Tube Assembly-Renew ........................................... 6-6
Brake Master Cylinder to Modulator Primary
Tube Assembly-Renew ........................................... 6-7
Rear Wheel Brake Front to Rear Tube Assembly
-Renew .................................................................. 6-8
RH Front Caliper to Modulator Tube Assembly
-Renew .................................................................. 6-9
Rear Wheel Brake Tube Assembly-Renew ............ 6-10
Dynamic Stability Control Module-Renew............ 6-11
Power Brake System (06.07) .................................. 6-7-1 Brake Booster ......................................................... 7-1
Emergency Brake Assist .......................................... 7-1
Specifications.......................................................... 7-2
Maintenance ........................................................... 7-2Brake Booster-RHD-Renew.................................... 7-2
Brake Booster-LHD-Renew .................................... 7-2 Brake Fluid Reservoir-Renew ................................. 7-3
Brake Bleeding - AMDS ......................................... 7-3
Brake Master Cylinder and Vacuum Booster
-Renew .................................................................. 7-4
Brake Master Cylinder-Renew ................................ 7-5
Anti-lock Braking System (ABS) (06.09)................. 6-9-1 Dynamic Stability Control ...................................... 9-1Concept ................................................................ 9-1
System Overview ................................................... 9-2
Operation Summary .............................................. 9-2
Traction Control ..................................................... 9-2 Functional Description ........................................... 9-2
Engine Intervention ................................................ 9-3
Brake Intervention ................................................. 9-3
ABS / DSC Circuit .................................................. 9-3
Specifications ......................................................... 9-3 Maintenance ......................................................... 9-4
ABS Modulator - Remove and Install ...................... 9-4

Power Brake System (06.07)
Brake System (06.00)
May 2007 Workshop Manual 6-7-1
Brake System (06.00)
Power Brake System (06.07)
Brake Booster
The brake booster comprises a chamber divided by a diap hragm plate and is secured to the brake pedal housing.
As the brake pedal is pressed, a poppet valve opens allowing at mospheric pressure into the drivers side of the diaphragm.
Atmospheric pressure builds up on the drivers side of the diaphragm and pushes against the partial vacuum on the other
side. This additional force boosts the a pplied brake pedal force up to 6.5 times.
When the brake pedal is released, the poppet valve closes. The pressure on the diaphragm reduces and the compression
spring returns the diaphragm to the release position.
Emergency Brake Assist
In an emergency braking situation, a driver presses down on the brake pedal much faster than in normal braking
conditions, but often without sufficient force. The initial appli cation of the brake pedal is a reflex reaction. After the initial
application, many drivers do not brake ha rd enough because of concerns that they might cause the vehicle to skid. To aid
the driver, the panic brake assist (PBA) intervenes in bringing the vehicle to a halt, sooner and in a controlled manner, in
emergency braking situation. The PBA system monitors the speed of brake pedal activation, and at a calibrated pedal
activation speed, the PBA provides maximum brake force and makes full use of the ABS.
PBA is controlled by the ABS/DSC module, which monitors a travel sensor attached to the internal vacuum diaphragm of
the brake booster. The sensor determines the position of th e diaphragm and the speed of the diaphragm movement. If the
sensor's signal indicates an emergency braking situation, the
ABS/DSC module will open an electric solenoid on the brake booster. The solenoid directs atmospheric pressure into the
rear of the brake booster, causing the booster diaphragm to mo ve forward to fully apply the brakes. PBA takes full benefit
of ABS to stop the vehicle in a controlled manner and in the shortest distance possible. When the brake pedal is released
the ABS/DSC module instantly releases the brakes.

Clutch Assembly (08.01)
8-1-4 Workshop Manual May 2007
8. Remove bolts (x2) that secure slave cylinder to torque tube (see Fig. 2).
9. Remove slave cylinder and collect spacer.
Installation
1. Clean slave cylinder, spacer and pipe adaptors.
2. Install spacer and slave cylinder and tighten bolts (x2).
3. Sportshift Only - Install clutch position sensor to slave
cylinder and secure with bolts.
4. Install pipe adaptors (x2) in slave cylinder.
5. Install bleed and supply pipes onto slave cylinder adaptors (x2) and secure with clips.
6. Install torque tube (see Workshop Manual procedure 05.01.CA Torque Tube Remove for Access and Refit).
7. Bleed clutch (see Workshop Manual procedure 08.00.AF Clutch Hydraulic System - Bleed).
8. Lower vehicle on ramp.
9. Connect vehicle battery.
Clutch Bleed Hose Assembly-Renew
08.00.AD
Removal
1. Raise vehicle on ramp.
2. Coupe Only - Remove deflector - front floor heatshield
(see Workshop Manual proc edure 09.04.AA Heatshield
- Front Floor - Renew).
3. Roadster Only - Remove exhaust sysytem (see
Workshop Manual procedure 09.00.NB Exhaust System
- Excluding manifold/down pipes - Renew). 4.
Roadster Only - Remove grommet sealing clutch bleed
pipe to torque tube.
5. Roadster Only - Position a piece of cloth in torque tube
aperture to collect spring clip (if dropped) and fluid loss.
6. Release clip and disconnect bleed hose from slave cylinder adaptor.
7. Plug slave cylinder to prevent fluid loss.
8. Release and remove bleed pipe assembly from support bracket.
Installation
1. Clean bleed hose assembly.
2. Remove plug from slave cylinder adaptor.
3. Install bleed hose and secure with clip.
4. Install bleed hose in support bracket.
5.Roadster Only - Install grommet sealing clutch bleed
pipe to torque tube.
6. Bleed clutch (see Workshop Manual procedure 08.00.AF Clutch Hydraulic System - Bleed).
7. Roadster Only - Install exhaust sysytem (see Workshop
Manual procedure 09.00.NB Exhaust System -
Excluding manifold/down pipes - Renew).
8. Coupe Only - Install deflector - front floor heatshield
(see Workshop Manual procedure 09.04.AA Heatshield
- Front Floor - Renew).
9. Lower vehicle on ramp.
Clutch Hydraulic System-Bleed-
Sportshift Only
08.00.AE
1. Raise vehicle on ramp.
2. Install Diagnostic tool and navigate to appropriate screen.
3. Position cloth around fluid reservoir to collect any spillage.
4. Remove fluid reservoir cap, en sure fluid level is correct
in reservoir.
5. Clean area around clutch bleed nipple.
6. Remove cap from bleed nipple.
7. Position bleed container containing clean hydraulic fluid, connect hose to bleed nipple.
8. Initiate bleed procedure on Diagnostic tool.
9. Loosen bleed nipple, allow air/fluid to escape and tighten bleed nipple.
10. Repeat procedure until air free fluid emerges.
11. Disconnect bleed hose, remo ve container, install dust
cap to bleed nipple.
12. Top-up fluid reservoir.
Fig. 2Warning
Always connect the battery earth (+ve) terminal first.
Repair Operation Time (ROT)
Before proceeding with the ne xt step, position a piece of
cloth in the torque tu be aperture to collect the spring clip
if dropped.
Caution
Always plug pipe ends to prevent ingress of dirt or moisture into the system.

Repair Operation Time (ROT)
ItemCode
Clutch Hydraulic System-Bleed
Warning
Observe all oil/fluid manufactu rers safety instructions
when handling components th at have been in contact
with transaxle oil.