fuel cap release ASTON MARTIN V8 VANTAGE 2010 Workshop Manual

Fuel Tank and Lines (10.01)
Fuel (10.00)
May 2007 Workshop Manual 10-1-11
Fuel Tank and Canister Assembly-Renew
Removal
1. Disconnect vehicle battery.
2. Remove rear subframe (see Workshop Manual procedure 02.01.CA Subframe Assembly - Rear -
Remove for Access and Refit).
3. Remove fuel filler cap.
4. Remove bolt filler pipe bracket to spring damper
assembly.
5. Remove nut filler neck pipe and hose to body.
6. Release filler neck pipe and hose, collect sealing washer.
7. Remove filler neck pipe and hose assembly from the tank (using filler neck disc onnection tool - 310 - 134)
(see Fig. 2). 8. loosen jubilee clip and disconnect hose from
evaporative emission contro l assembly (see Fig. 3).
9. Disconnect fuel tank harness from main harness (see Fig.
4).
10. Remove nut and release earth lead from stud (see Fig. 5).
Repair Operation Time (ROT)
Warning
Read and follow all fuel hand ling instructions (at the
beginning of the Fuel System section) and the fuel
bowser manufacturers fuel handling documentation
before commencing work on the fuel system. Clean up
spillages immediatel y and dispose of fuel contaminated
materials safely.
Warning
Fuel vapour is explosive. During the following
procedure, fuel tank and fuel lines will be open. Ensure
good ventilation and take all necessary precautions to eliminate fire risk.
Warning
Fire Risk. Before commencing work on the vehicle fuel system, disconnect the earth ( - ve) lead from the
vehicle battery.
Fig. 2
$
Fig. 3
Fig. 4
Fig. 5
$
$%
$&

Fuel Tank and Lines (10.01)
Fuel (10.00)10-1-14 Workshop Manual May 2007
3. Remove fuel filler cap.
4. Remove bolt filler pipe bracket to spring damper
assembly.
5. Remove nut filler neck pipe and hose to body.
6. Release filler neck pipe and hose, collect sealing washer.
7. Remove filler neck pipe and hose assembly from the
tank (using filler neck disc onnection tool - 310 - 134)
(see Fig. 2).
8. loosen jubilee clip an d disconnect hose from
evaporative emission control assembly (see Fig. 3). 9. Disconnect fuel tank harness from main harness (see
Fig. 4).
10. Remove nut and release earth lead from stud (see Fig. 5).
11. Disconnect vapour purge and fuel pipe from the tank
12. Remove bolts (x4) exhaust heatshield to floor.
13. Remove nuts (x5) oil cooler pipes to body.
14. Release exhaust vacuum pipe from clips.
15. Remove vacuum hose clips from studs.
16. Remove vacuum hose clip bolts/stud (x4) tank to body.
Fig. 2
Fig. 3
$
$
Fig. 4
Fig. 5
Warning
The fuel tank is heavy. Fuel tank removal / replacement is a two person operation.
$
$&

Fuel Tank and Lines (10.01)
Fuel (10.00)
May 2007 Workshop Manual 10-1-15
17. With assistance support tank, remove bolts (x14) tank to body and remove fuel tank (see Fig. 6).
Installation
1. With assistance position tank and secure with bolts (x14)
2. Install vacuum hose clip to tank bolts / studs (x4)
3. install vacuum hose clips to studs and secure vacuum hose.
4. Install nuts (x5) oil cooler to body.
5. Install heatshield.
6. Connect vapour purge and fuel pipe to tank.
7. Position earth lead and secure with nut.
8. Connect fuel tank harness to main harness.
9. Connect evaporative emission control assembly hose and secure with jubilee clip.
10. install filler neck pipe and hose assembly to fuel tank.
11. Position filler neck pipe, hose assembly and sealing washer to body.
12. Install nut filler neck pipe and hose assembly to body.
13. Install bolt filler pipe bracket to spring damper assembly.
14. install fuel filler cap
15. Install rear subframe (see Workshop Manual procedure 02.01.CA Subframe Assembly - Rear - Remove for
Access and Refit). 16. Connect vehicle battery.
Fuel Tank Sender Assembly-Renew
Removal
1. Disconnect battery earth lead.
2. Release and remove luggage compartment rear floor
carpet.
3. Remove luggage compartment front floor carpet retainers (x6) and remove carpet.
4. Remove fuel tank cover, clean off the sealant around the aperture.
5. Remove nuts (x7) and release plate clamp and fuel tank service cover.
Fig. 6
Warning
The fuel tank is heavy. Fuel tank removal / replacement
is a two person operation.
Warning
Fire Risk. Do Not connect the vehicle battery and
switch on the ignition until all work on the fuel system
is completed and the area is cleared of fuel
contamination. Remove contaminated material, open fuel containers
and waste fuel. Fully ventilate vehicle and work area to remove all fuel fumes.
$
Warning
Fire Risk. Do Not start the en gine until the fuel system
integrity is confirmed.
Repair Operation Time (ROT)
Warning
Read and follow all fuel hand ling instructions (at the
beginning of the Fuel System section) and the fuel
bowser manufacturers fuel handling documentation
before commencing work on the fuel system. Clean up
spillages immediately and dispose of fuel contaminated materials safely.
Warning
Fuel vapour is explosiv e. During the following
procedure, fuel tank and fuel lines will be open. Ensure
good ventilation and take all necessary precautions to eliminate fire risk.
Warning
Fire Risk. Before commencing work on the vehicle fuel system, disconnect the earth ( - ve) lead from the vehicle battery.
Warning
Ensure there is adequate ventilation inside the vehicle
(i.e. place the vehicle in a well ventilated area, with the windows open).
Caution
The following procedure is completed inside the vehicle
cabin area. Extra care must be taken to ensure no fuel or
fuel vapours come into contac t with the vehicle interior.