AUDI A3 1996 8L / 1.G AEB ATW Engines Lubrication System Components Workshop Manual

17-1


Lubrication system
components, removing and
installing

WARNING!

Do not re-use any fasteners that are worn or
deformed in normal use.
Some fasteners are designed to be used only
once, and are unreliable and may fail if used
a second time. This includes, but is not
limited to, nuts, bolts, washers, circlips and
cotter pins. Always follow the
recommendations in this manual-replace
these fasteners with new parts where
indicated, and any other time it is deemed
necessary by inspection.

CAUTION!
If large quantities of metal particles or other
deposits (caused, for example, by partial
seizure of the crankshaft or connecting rod
bearings) are found in the engine oil, the oil
passages must be cleaned thoroughly and
the oil cooler replaced in order to prevent
further damage from re-occurring.
Do not overfill with oil past the MAX mark on
Pa
ge 1 of 33 Lubrication s
ystem com
ponents, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.17.1

the oil dipstick. Damage to the Three Way
Catalytic Converter (TWC) could result.
Markings, refer to illustration Page 17
-27
.
Viscosity classes and oil specifications Page
17
-26
.
Pa
ge 2 of 33 Lubrication s
ystem com
ponents, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.17.1

17-2


Part I

CAUTION!
Part numbers are listed here for reference only.
Always check with your Parts department for
the latest information.
1 -
O-ring Always replace
2 -
Suction pipe Clean strainer if dirty
3 -
Bolt 10 Nm (7 ft lb)
4 -
Baffle plate
5 -
Bracket For torque support
6 -
Stop For torque supportAdjusting:
- Place stop for torque support on rubber
buffer for torque support and tighten
bolts to 25 Nm (18 ft lb)
7 -
Bolt
Pa
ge 3 of 33 Lubrication s
ystem com
ponents, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.17.1

25 Nm (18 ft lb)
Pa
ge 4 of 33 Lubrication s
ystem com
ponents, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.17.1

17-3


8 -
Bolt
25 Nm (18 ft lb)
9 -
Nut 25 Nm (18 ft lb)
10 -
Brace
11 -
Nut 25 Nm (18 ft lb)
12 -
Side brace
13 -
Bolt 20 Nm (15 ft lb)
14 -
Oil pump housing
15 -
Gears Backlash, checking Fig. 1Axial clearance, checking Fig. 2
16 -
Oil pump cover with pressure relief valve
Opening pressure: 5.7-6.7 bar (82.65-
97.15 psi)
17 -
Bolt 25 Nm (18 ft lb)
18 -
Bolt
Pa
ge 5 of 33 Lubrication s
ystem com
ponents, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.17.1

10 Nm (7 ft lb)
Pa
ge 6 of 33 Lubrication s
ystem com
ponents, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.17.1

17-4


19 -
Bolt
45 Nm (33 ft lb)
20 -
Oil drain plug 50 Nm (37 ft lb)
21 -
Sealing washer Always replace
22 -
Oil pan Removing and installing Page 17
-9
Clean contact surface before installingWhen installing oil pan on removed engine,
note that oil pan is aligned with metal plate
on flywheel side (i.e. oil pan projects out
over engine block 0.8 mm 0.031 in.) Before installing oil pan, spread thin coat of
sealant AMV 174 004 01 on sealing
surface between oil seal carrier and engine
block
23 -
Bolt 10 Nm (7 ft lb)Use 3249 hex ball socket to remove and
install two rear bolts on transmission Tighten diagonally in sequence
Pa
ge 7 of 33 Lubrication s
ystem com
ponents, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.17.1

17-5


CAUTION!
Part numbers are listed here for reference only.
Always check with your Parts department for
the latest information. 24 -
Gasket
Always replace
25 -
Bolt 10 Nm (7 ft lb)
26 -
Oil return line From turbocharger
27 -
Gasket Always replaceInstall dryOnly spread thin coat of sealant AMV 174
004 01 on front and rear sealing surfaces
between oil seal carrier and engine block
Pa
ge 8 of 33 Lubrication s
ystem com
ponents, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.17.1

17-6


Part II

1 -
Oil filter bracket
2 -
Gasket Always replace
3 -
Oil retaining valve 8 Nm (71 in. lb)
4 -
Gasket Always replace
5 -
Coupling 30 Nm (22 ft lb)
6 -
Oil feed line 25 Nm (18 ft lb)To turbocharger
7 -
Bolt 20 Nm (15 ft lb)
8 -
Lower coolant pipe
9 -
Sealing washer If leaking, cut open and replace
10 -
Oil pressure switch -F1-, 1.4 bar (20.3 psi) 25 Nm (18 ft lb)
Pa
ge 9 of 33 Lubrication s
ystem com
ponents, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.17.1

Black insulationCheck Page 17
-22
Pa
ge 10 of 33 Lubrication s
ystem com
ponents, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.17.1