oil AUDI A3 1996 8L / 1.G ATW Engine Motronic Fuel Injection Syst

disconnect connector from ignition coils and
from fuel injectors.
Pa
ge 2 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-12


Repair Manual, 1.8 Liter 4
-Cyl. 5V Turbo Engine
Mechanical, Engine Code(s): AEB, ATW, Repair Group 21, Charge air system with turbocharger, checking

Repair Manual, 1.8 Liter 4
-Cyl. 5V Turbo Engine
Mechanical, Engine Code(s): AEB, ATW, Repair Group 26; Secondary Air Injection (AIR) system, checking
22 -
Fuel injectors -N30- through -N33- Checking Page 24
-38
Removing and installing Page 24
-46
23 -
Ignition coils -N-, -N128-, -N158-, -N163-
Checking Page 28
-4
24 -
Wastegate bypass regulator valve -N75-
Checking:
25 -
Mass Air Flow (MAF) sensor -G70-
Checking Page 24
-60
26 -
Secondary Air Injection (AIR) pump
motor-V101-
Checking:
Pa
ge 13 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-43


Fuel rail with fuel injectors, disassembling
and assembling

1 -
Fuel injector insert, 3 Nm
Use fluid securing material D 000 600 A2
to insert.
2 -
O-ring Removing and installing Page 24
-46
Always replaceCoat with clean engine oil
3 -
Fuel injectors -N30- through -N33- Removing and installing Page 24
-46
Pa
ge 48 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-44


4 -
O-ring
Removing and installing Page 24
-46
Always replaceCoat with clean engine oil
5 -
Fuel distributor
6 -
Fuel supply line Tighten to 25 Nm
7 -
Fuel return line
8 -
Harness connector for injectors4x
9 -
Socket head bolt- 10 Nm
10 -
Fuel pressure regulator
Pa
ge 49 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-47

- Disconnect fuel distributor with injectors from
intake plenum and set aside in rear of engine
compartment on a clean cloth.

WARNING!

Fuel system is under pressure! Before
opening system, place rags around the
connection point. Then release pressure by
carefully loosening connection.

- Disengage retaining clip and remove fuel
injector.

Note:
Fuel lines must be removed before replacing fuel
distributor.
Installation is reverse of removal, noting the
following:

Remove O-rings at all opened connections.
(Never remove plastic cap from valve head
to replace front O-ring - pry O-ring off over
plastic cap).
Lightly lubricate O-rings with clean engine
oil.
Pa
ge 52 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1