oil AUDI A3 1998 8L / 1.G AEB ATW Engines Sealing Flanges And Flywheel Driveplate Workshop Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 1998, Model line: A3, Model: AUDI A3 1998 8L / 1.GPages: 11, PDF Size: 0.25 MB
Page 1 of 11

13-36
 
  
Sealing flange and 
flywheel/drive plate, removing 
and installing Note:  
Servicing clutch: 
 
 Repair Manual, 5 Spd. Manual Transmission 
012/01W Front Wheel Drive, Repair Group 30
 
 
 Repair Manual, 5 Spd. Manual Transmission 
01A All Wheel Drive, Repair Group 30
 
1 - 
Oil seal 
To remove, remove oil seal carrier, item - 
15 - Install using 10-203Lightly oil lip of seal
2 - 
Woodruff key Check for proper installation
3 - 
Connecting bolt 25 Nm (18 ft lb)
4 - 
Front oil seal flange Before installing oil pan, spread sealant 
AMV174 004 01 on joint between oil seal 
flange and cylinder block. 
Pa
ge 1 of 11 Sealin
g flan
ge and fl
ywheel/drive 
plate, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.13.2 
Page 3 of 11

13-38
 
  
10 - 
Bolt 
10 Nm (7 ft lb)
11 - 
Rear oil seal flange With oil sealReplace as complete unitLightly oil lip of sealBefore installing oil pan, spread sealant 
AMV 174 004 01 on joint between oil seal 
flange and cylinder block 
12 - 
Oil seal Replacing  Page 13
-39
13 - 
Intermediate shaft 
Axial play, max: 0.25 mm (0.010 in.)
14 - 
O-ring Always replace
15 - 
Oil seal carrier for intermediate shaft 
Pa
ge 3 of 11 Sealin
g flan
ge and fl
ywheel/drive 
plate, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.13.2 
Page 4 of 11

13-39
      
Crankshaft oil seal (toothed belt side), 
replacing
 
     
Engine installed 
     Lock carrier in service position   Page 13
-1 
     
Special tools and equipment  
     
2085 seal puller
     3083 arbor
     3099 spur belt spreading 
     
Removing  
     
-  Remove ribbed belt and ribbed belt tensioner   
Page 13
-15
 . 
     
-  Remove toothed belt   Page 13
-29
 .
     
-  Remove mounting bracket for torque arm   
Page 17
-2 , item - 5 -. 
    
-  Remove crankshaft toothed belt gear. Secure toothed belt gear using 
3099 spur belt spreading. 
Pa
ge 4 of 11 Sealin
g flan
ge and fl
ywheel/drive 
plate, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.13.2 
Page 6 of 11

13-40
 
    
-  Before attaching seal puller, insert socket head cap bolt from 3083 
arbor into crankshaft to stop. 
-  Unscrew inner part of 2085 seal puller two turns (approx. 3 mm 0.118 
in.) and secure using knurled bolt. 
    
-  Grease threaded head of 2085 seal puller, position and with forced 
pressure screw into oil seal as far as possible. 
-  Loosen knurled bolt and turn inner part against crankshaft until oil seal 
is removed. 
Pa
ge 6 of 11 Sealin
g flan
ge and fl
ywheel/drive 
plate, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.13.2 
Page 7 of 11

13-41
      
Installing  
     
-  Lightly oil lip of oil seal. 
    
-  Place guide sleeve from 3083 arbor on crankshaft.
-  Slide oil seal over guide sleeve.
    
Note:  -  Press in oil seal to stop together with pressure bushing and bolt from 
3083 arbor. 
-  Replace bolt for toothed belt gear.
-  Install toothed belt gear for crankshaft and secure using 3099 spur belt 
spreading. 
Contact surface between toothed belt gear and crankshaft must be 
free of oil. Do not grease crankshaft bolt for toothed belt gear.
-  Install toothed belt (adjust valve timing)   Page 13
-32
 .
Pa
ge 7 of 11 Sealin
g flan
ge and fl
ywheel/drive 
plate, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.13.2