AUDI A3 1998 8L / 1.G AEB ATW Engines Sealing Flanges And Flywheel Driveplate Workshop Manual

AUDI A3 1998 8L / 1.G AEB ATW Engines Sealing Flanges And Flywheel Driveplate Workshop Manual A3 1998 8L / 1.G AUDI AUDI https://www.carmanualsonline.info/img/6/955/w960_955-0.png AUDI A3 1998 8L / 1.G AEB ATW Engines Sealing Flanges And Flywheel Driveplate Workshop Manual
91 100 133

Page 1 of 11

AUDI A3 1998 8L / 1.G AEB ATW Engines Sealing Flanges And Flywheel Driveplate Workshop Manual 13-36
 
  
Sealing flange and 
flywheel/drive plate, removing 
and installing Note:  
Servicing clutch: 
 
 Repair Manual, 5 Spd. Manual Transmission 
012/01W Front Wheel Drive, Repair Group 30
 
 
 R

Page 2 of 11

AUDI A3 1998 8L / 1.G AEB ATW Engines Sealing Flanges And Flywheel Driveplate Workshop Manual 13-37
 
  
5 - 
Gasket 
Always replace
6 - 
Cylinder block Crankshaft, removing and installing   
Page 13
-46
 
Pistons and connecting rods, 
disassembling and assembling   Page 13
-
53
 
7 - 
Mountin

Page 3 of 11

AUDI A3 1998 8L / 1.G AEB ATW Engines Sealing Flanges And Flywheel Driveplate Workshop Manual 13-38
 
  
10 - 
Bolt 
10 Nm (7 ft lb)
11 - 
Rear oil seal flange With oil sealReplace as complete unitLightly oil lip of sealBefore installing oil pan, spread sealant 
AMV 174 004 01 on joint between

Page 4 of 11

AUDI A3 1998 8L / 1.G AEB ATW Engines Sealing Flanges And Flywheel Driveplate Workshop Manual 13-39
      
Crankshaft oil seal (toothed belt side), 
replacing
 
     
Engine installed 
     Lock carrier in service position   Page 13
-1 
     
Special tools and equipment  
     
2085 seal pulle

Page 5 of 11

AUDI A3 1998 8L / 1.G AEB ATW Engines Sealing Flanges And Flywheel Driveplate Workshop Manual Note:  
3415 special tool can also be used. 
Pa
ge 5 of 11 Sealin
g flan
ge and fl
ywheel/drive 
plate, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t

Page 6 of 11

AUDI A3 1998 8L / 1.G AEB ATW Engines Sealing Flanges And Flywheel Driveplate Workshop Manual 13-40
 
    
-  Before attaching seal puller, insert socket head cap bolt from 3083 
arbor into crankshaft to stop. 
-  Unscrew inner part of 2085 seal puller two turns (approx. 3 mm 0.118 
in.) and s

Page 7 of 11

AUDI A3 1998 8L / 1.G AEB ATW Engines Sealing Flanges And Flywheel Driveplate Workshop Manual 13-41
      
Installing  
     
-  Lightly oil lip of oil seal. 
    
-  Place guide sleeve from 3083 arbor on crankshaft.
-  Slide oil seal over guide sleeve.
    
Note:  -  Press in oil seal to stop

Page 8 of 11

AUDI A3 1998 8L / 1.G AEB ATW Engines Sealing Flanges And Flywheel Driveplate Workshop Manual 13-42
      
-  Place torque arm on rubber buffer for torque arm 
and tighten bolts to 25 Nm (18 ft lb). 
     
-  Install ribbed belt and ribbed belt tensioner   
Page 13
-15
 . 
     
Note:  
     W

Page 9 of 11

AUDI A3 1998 8L / 1.G AEB ATW Engines Sealing Flanges And Flywheel Driveplate Workshop Manual 13-43
      
Dual-mass flywheel/drive plate, 
removing and installing
 
     
Special tools and equipment  
      10-201 flywheel retainer  
     
Dual-mass flywheel  
    
Tightening torque  -  Reloc

Page 10 of 11

AUDI A3 1998 8L / 1.G AEB ATW Engines Sealing Flanges And Flywheel Driveplate Workshop Manual 13-44
      
Drive plate  
     
Removing  
    
Installing   -  Relocate 10-201 flywheel retainer to loosen and tighten bolts.
-  Mark drive plate to engine. 
    
-  Install drive plate with shim -2
Page:   1-10 11-20 next >