battery AUDI A3 2015 Owner's Manual

210 Check ing and F illin g
Only pull on the loop until you fee l resist ­
ance. You will not hear it release . Other­
w ise you could damage the emergency re­
lease mechanism .
Hood
Working in the engine compartment
Special care is required if you are working in
the engine compartment
F o r w ork in th e engine co mpartm ent such as
c h ec king an d filling fluids, there i s a ri sk of
inj ury, sca lding, a ccid ent s, and b urn s. For
t hi s re ason , fo llow all th e followin g lis te d
warn in gs a nd ge neral safe ty pr eca utions.
Th e e ngine compartment is a d ange rous
area .¢ .& .
&_ WARNING
To reduce the risk of injury, before you
check anyth ing under the hood:
- Turn the engine off.
- Set the parking brake.
- Place the selector leve r in the P position.
- Remove the ignit io n key .
- Let the engine coo l down.
- To reduce the r isk of being burned, never
open the hood if you see or hear steam
or coolant escaping from the engine
compartment . Wait until no steam or
coolant can be seen or hea rd before ca re­
fully opening the hood.
- Keep chi ldren away from the engine com­
partment .
- Never spill flu ids on a hot engine. These
fluids (such as the freeze protection con­
tained in the coolant) can catch fi re.
- Avoid short circuits in the electrical sys­
tem, especially the battery.
- When working in the engine compart­
ment, remembe r that the radiator fan
can switch on even if the ignition is
switched off, which increases the risk of
persona l injury . -
Never open the cap on the coolant ex­
pans ion tank when the eng ine is warm.
The coolant system is under pressure.
- To protect your face, hands, and arms
from hot steam or coolant, cover the cap
with a large cloth when opening.
- Do not remove the engine cover under
any circumstances . This increases the
risk of burns .
- If tests need to be performed with the
engine runn ing , there is add itional dan­
ger due to moving components (such as
the ribbed belt, generator and radiator
fan) and from the high voltage ignit ion
system.
- Never touch the rad iator fan . The auxili­
ary electric fan is temperature controlled
and can switch on suddenly.
- Pay attention to the fo llow ing warnings
listed when wo rk on the fuel system or
on the e lectr ica l equipment is req uired.
-A lways disconnect the vehicle battery
from the vehicle electr ical system
- Do not smoke
- Never work near open flames
- Always have a wo rk ing fire exting uisher
nearby
- To avo id e lectr ica l sho ck and pe rsonal in­
jury whi le the engine is running or being
started, never touch:
- Ign it ion cables
- Other components of the high voltage
electronic ignition system.
- If you must perform a check or repair
with the eng ine running:
- First, fully app ly the parking brake,
move selector lever to P (Park).
- Always use extreme caut io n to prevent
cl othing, jewelry, or long hair from get­
ting caught in the radiator fan, V-be lts
o r other moving parts, o r from contact­
ing hot parts. Tie back hair before
starting, and do not wear clothing that
will hang or droop into the engine.
- Minimize exposure to emission and
chemical hazards¢,& . ..,.

,&_ WARNING
California Proposition 65 Warning:
- Engine exhaust, some of its constituents,
and certain vehicle components contain
or emit chemicals known to the State of
California to cause cancer and birth de­
fects and reproductive harm. In addition, certain fluids contained in vehicles and
certain products of component wear con­
tain or emit chemicals known to the
State of California to cause cancer and birth defects or other reproductive harm .
- Battery posts, terminals and related ac­
cessories contain lead and lead com­
pounds, chemicals known to the State of
California to cause cancer and reproduc­
tive harms. Wash hands after handling.
(D Note
When filling fluids, be sure not to mix the
fluids up. Otherwise severe malfunctions and engine damage will occur.
@) For the sake of the environment
You should regularly check the ground un­ der your vehicle in order to detect leaks
quickly .
If there are visible spots from oil
or other fluids, bring your vehicle to an au­
thorized Audi dealer or qualified repair fa­
cility to be checked.
Opening the hood
The hood is released from the interior.
Fig. 147 Sect ion of the driver's footwell: release lever
Checking and Filling 211
Fig. 148 Rocke r switch un der t he hood
Make sure the wiper arms are not raised up
from the windshield. Otherwise the paint
could be damaged .
The hood can only be released with the driv­
er's door open .
.,. Pull the lever under the instrument panel in
the direction of the arrow¢
fig. 147 .
.,. Raise the hood slightly¢,&. .
.,. Press the rocker switch under the hood up ­
ward
c:> fig. 148. This releases the catch.
.,. Open the hood .
.&, WARNING
Never open the hood when you see that
steam or coolant drips from the engine
compartment- there is a danger of burns!
Wait until no steam or coolant flows out.
- To reduce the risk of being burned, never open the hood if you see or hear steam
or coolant escaping from the engine
compartment. Wait until no steam or
coolant can be seen or heard before care­
fully opening the hood .
Closing the hood
.,. Push the hood down until the force of the
strut is overcome . -
.,. Then lower the hood and let it fall into the
engine hood latch -you do
not have to press
on the hood after it is locked. ¢ ,&. .
.&, WARNING -
A hood that is not completely latched
could fly up and block your view while driv­ ing.

212 Checking and Filling
- When you close the engine hood, check it
to make sure the safety catch has proper­
ly engaged. The hood should be flush
with the surrounding vehicle body parts.
Engine compartment overview
The most important check points.
- If you notice while driv ing that the hood
is not secured properly, stop at once and
close it.
Fig. 149 Typ ica l locat ion of the reservoir, en g in e oil d ipstick, and engine o il filler opening
(D Coolant expansion tank (- L) .. .
@ Engine oi l dipstick ... .... .. . .
® Engine oil filler opening (~) .
@ Brake fluid reservo ir ((0)) .. .. .
® Battery(+) under a cover .. .. .
@ Body ground point(-)
0 Washer f luid reservoir (~) ... .
@ Fuse housing ....... .... ... .
2 17
215
215
219
221
224
255
The engine oil filler opening and the dipstick (items ® and @)
c::> fig. 149 may be located in
a different area depending on engine version .
A WARNING ,...,___ -
Before you check anything in the engine
compartment, always read and heed all
WARNINGS
c::> page 210.
Engine oil
Engine oil specifications
The engine in your Audi needs the right kind
of oil.
The eng ine in your Audi is a sophisticated
power plant that was built to exacting specifi ­
cations . This engine needs the right kind of
engine oil that meets specifications regarding
quality and v iscosity so that it can run
II>-

220 Checking and Filling
Battery
General information
Under normal operating conditions, the bat­
tery in your Audi does not need any mainte­
nance. With
high outs ide temperatu res or
long daily drives we recommend that you have
the electro lyte level checked by a service fa­
cility. The e lectrolyte level shou ld also be
checked each time the battery is charged
c:>page222.
Have the battery checked when you take your
vehicle in for service. You are well advised to replace a battery that is older than 5 years.
With certain types o f airbag deployment, the
battery is disconnected from the vehicle elec ­
trica l system for safety reasons
c;, .&. in Re­
pair , care and disposal of the airbags on
page 156.
Disconnecting the battery terminals
Some vehicle functions such as power win­
dows are unavai lable if the battery termina ls
are d isconnected. These functions have to be
relearned after the battery terminals are con­
nected again. To prevent this, the battery
should only be disconnected from the vehicle
electrical system when absolutely necessary
for repairs .
To reprogram the functions, proceed as fol­ lows:
Function Reprogramming
Power window one-c;, page 40, Correcting
touch up/down power window mal-
function functions
Remote control key If the vehicle does not
or react to the key, it
convenience key must be synchroni zed
c:>page 33
Digital clock c:>page 10
ESC indicator light The indicator light
goes out after driving
a few meters
Vehicles not driven for long periods
If you do not drive your vehicle over a period
of severa l days or weeks, e lectrica l compo­
nents are gradually sca led back or switched
off. This reduces energy consumption and
maintains starting capability over a longer pe­
riod
c;, page 190. Some of the conven ience
functions may not operate, such as the interi­
or lights or power seat adjustment. The con ­
venience functions will be availab le aga in
when you switch on the ignition and start the
engine.
Winter operation
During the winter months, battery capacity
tends to decrease as temperatures drop. This
is because more power is also consumed wh ile
sta rting, and the headlights, rear window de­
fogger, etc. , are used more often.
Avoid unnecessary power consumpt ion, par­
ticularly in city traffic or when traveling only
short distances. Let your authorized Aud i
dealer check the capacity of the vehicle bat­
tery before winter sets in ~ page 222. A well
charged battery will not on ly prevent starting
problems when the weather is cold, but will
also last longer.
A WARNING -
-Work on the battery requ ires expert
know ledge. Contact your authorized Audi
dealer qualified repair facility for infor­
mat ion regarding the vehicle battery.
There is a risk for chemical burns or ex­
p losions.
- Never open the vehicle batte ry . Do not
try to change the battery electrolyte lev­
el. Otherwise explosive gas will escape
from the battery and increase the risk of
an explosion .
(i) Tips
If your vehicle is left standing for several
weeks at extremely low temperatures, the
vehicle battery should be removed and
stored where it w ill not freeze. This will ..,.

prevent it from being damaged and having
to be replaced .
Working on the battery
Be especially careful when working on or near
the battery.
The battery is loca ted in the luggage compart­
men t under the floor. Before yo u check any­
thing in the l uggage compartment,
read and
hee d all WARNINGS
¢ _A .
Always heed the sa fe ty warning s, when work­
i ng on the vehicle battery or the vehi cle elec ­
trica l system to prevent injury.
The following WARNINGS are very
impo rtant when working on the battery:
Alway s heed th e following WARNING SYM-
BOLS and saf ety precaution s when working
o n the b att ery.
®
Always wear e ye protection.
A
Batter y ac id contains sulfu ric acid .
Always w ear glo ves and e ye p rote c-
t ion .
@
No
- spark s
- flames
- smo king.
~
Wh en a battery i s charge d, it produ -
ce s hy d rogen ga s whi ch i s ex plo siv e
and could cau se perso na l injur y.
®
Alway s keep the b atter y w ell o ut of
r e ach of childr en.
A WARNING
Whenever working on the bat tery or on
the electrical system, there is the risk of
injury, accident and even fire. Read and
heed the following WARNINGS :
- Always wear eye p rotection. Do not let
battery acid or any lead particles get on
yo ur sk in or clothing. Sh ield your eyes.
Explosive gases can cause blindness or
other injury.
-
Checking and Fillin g 221
-Battery acid contains sulfuric acid . Sulfu­
ric acid can cause blindness and severe
burns.
- Always wear g loves and eye protection.
Do no t tilt the ba ttery because acid
could leak out of the ventilat ion open­
ings .
- If you ge t bat tery acid in your eyes or
on your skin, immediately rinse with
cold water for several minutes and get
med ical attention .
- If you should ingest any batte ry acid,
seek medical attention immediately.
- Do not expose the ba tte ry to an open
f lame, e lectric sparks or an open light .
- Do not smoke.
- Do not in terchange t he positive and neg-
ative cables.
- When working on t he battery, be su re
not to short-cir cuit the termina ls w ith
too ls or othe r metal objects. This would
cause the battery to heat up very quickly,
which could lead to damage or explosion
and pe rsonal injury.
- When a battery is charged, it produces
hydrogen gas which is explosive and
could cause personal inju ry.
- Always keep the battery well out of the
reach of children.
- Before work is done on the elect rical sys ­
tem, disconnect the negative ground ca ­
ble.
- Before performing any work on the e lec­
trical system, switch off the engine and ignit ion as well as any electrical equip­
ment. The negative cable on the battery
must be disconnected. If you are just go­
ing to replace a light bulb, then it is
e nough to switc h off the lights.
- Before disconnecting the battery, switch off the anti-theft alarm system! Other­
wise you will set off the alarm.
- When disconnecting the battery, first
disconnect the negat ive cab le and then
the posit ive cab le.
- Before reconnecting the battery, ma ke
sure all e lectr ica l consumers are sw itch­
ed off. Reco nne ct the pos it ive cable first
•
•
•

222 Checking and Fill in g
and then the negative cable . Never inter­
change the cables -this could start a fire!
- Never charge a frozen or a thawed-out
battery. It could explode! If a battery has
frozen, then it must be replaced. A dead battery can freeze over at 32°F (0°C).
- Make sure the vent hose is always attach­
ed to the opening on the side of the bat­
tery.
- Never use batteries which are damaged.
There is the danger of an explosion! Al­
ways replace a damaged battery.
&_ WARNING
California Propos ition 65 Warning:
- Battery posts, terminals and related ac­
cessories contain lead and lead com­
pounds, chemicals known to the State of
California to cause cancer and reproduc­
t ive p roblems. Wash hands after han­
dling.
(D Note
- Do not d isconnect t he veh icle battery
when the ignition is on or when the en­
gine is running, otherwise, you will dam­
age ele ctron ic componen ts in the elec tri ­
ca l system.
- If your vehicle is going to stand for a
l ong period of time wi thout being driven,
protect the battery from "freezing", oth­
e rwise it w ill be damaged and wi ll then
have to be replaced.
Battery charging
Starting the engine requires a well charged battery.
F ig . 1 54 Engine co mpartment : connectors for a charg­
er and jump start cab les
Alwa ys read and heed all WARNINGS below
c> &. and c> &. in Working on the battery on
page 221.
.. Switch off the ignition and all electrical con­
sumers.
.. Make sure the area is well ventilated when
you charge the battery .
.. Open the eng ine hood
r=;, page 211 .
.. Open the red cover on t he positive pole
r=;, fig. 154 .
.. Clamp the ch arger term inal clamps as in­
structed on the
batter y terminal (+ ) and on­
ly o n the
body ground po int (-) .
.. On ly now plug the mains lead for the charg­
ing equ ipment into the wa ll outlet and turn
iton
c> &, .
.. Make sure th e charging rate is not over
30 amps /14 .8 volts .
.. When the battery is fully charged: Turn the
charg ing equipment off and remove the
mains lead from the wall ou tlet .
.. Now remove the clamps for the cha rging
equipment .
.. Close the red cover on the positive pole .
.. Close the hood
~ page 211.
A d ischarged bat tery can freeze at tempera ­
tu res of only 32 F
0 (0 °C). Allow a frozen bat­
tery to thaw completely before attempting to charge it
r=;, .&, . However, we recommend not
using a thawed battery again because the bat­
te ry casing can be cracked due to ice forma-
t ion and can leak battery acid . ..,.

Battery charging (Ma ximum charging rate
o f 30 am ps/ 14.8 volt s)
When charging at
low voltages (e.g . with a
tri ckle ch arg er), the batte ry cables do not
have to be d isconnected first. The battery
caps should
not be opened when charging a
battery .
It is not necessary to remove the battery from
the luggage compartment, and it is also not
necessary to disconnect the cables.
F ast charging th e battery (charging rate
a bo ve 14 .8 volt s)
For technical reasons do not use a battery
charger that uses voltage greater than 14.8
volts to charge your ve hicle 's battery .
A WARNING
Charging a battery can be dangerous .
- Always follow the operating instructions
provided by the battery charge r manu­
fact urer when charging your battery .
- Never charge a frozen battery . It may ex ­
plode because of gas t rapped in the ice .
Allow a frozen battery to thaw out first.
- Do not reuse batteries which we re fro ­
zen . The batte ry housing may have
cr acked and weakened whe n the battery
froze.
- Charge the battery in a we ll ventilated
area. Keep away from open flame o r ele c­
trical spark. Do not smoke. Hydroge n gas
generated by the battery is exp losive.
- T o redu ce the danger o f explosion , never
conne ct or disconnect cha rger cables
wh ile the charger is operating .
- F ast charg ing a battery i s dangerous and
sho uld on ly be attempted by a compe­
tent technician with the proper eq uip ­
me nt.
- Battery acid that may spill during charg ­
ing should be washed off with a so lution
of warm water and ba king soda to neu­
tralize the acid.
Checking and Fillin g 223
@ Note
Neve r use a fast charger as a booster to
start the eng ine . This w ill seriously dam­
age sens itive e lectronic components, such
as contro l units, relays, radio, etc., as well
as the batte ry charger .
Battery replacement
The new ba ttery mus t hove the some specifi­
cations and dimensions as the original equip­
ment battery .
Intelligent energy management in your vehi­
cle is responsible for distributing the electri­
ca l ene rgy throughout your vehicle
~ page 190 . The intelligent energy manage­
ment system will keep the engine battery
c h arged better than vehicles without this sys­
tem. To make sure the addition al ele ctri cal e n­
ergy is ava ilab le once again after yo u have
changed the batte ry, we recommend that you
insta ll batteries of the same type an d manu­
facture on ly (the same as those insta lled at
the time your veh icle was delivered) . Specif i­
cations are listed on the battery housing. Your
authorized dea ler must code the battery in
the ene rgy management system to enab le you
to use the ene rgy management functions cor­
re ct ly afte r repla cing the battery.
The new battery must have the same capacity,
vo ltage ( 12-volts) , amperage, construction
and plug sea ling .
When install ing the battery, make sure the ig­
nition and a ll electrical consumers are switch ­
ed off .
~ Note
Make sure the ventilat ion hose on the side
of the battery is con nected, otherwise
fumes o r batte ry acid can lea k out.
@) For the sake of the environment
Because of the prob lem of proper disposal
of a battery, we recommend your author ­
i zed Audi dealer change the battery for
you. Batteries contain sulfur ic acid and ..,.
•
•
•

Gross Vehicle Weight Rating ("GVWR")
means the maximum total loaded weight of
the vehicle .
Groove
means the space between two adjacent tread
ri bs.
Load rating (code)
means the maximum load that a tire is rated
to carry for a given inflat ion pressure . You
may not find this information on all tires be­
cause it is not requ ired by law .
Ma ximum load rating
means the load rating for a t ire at the max i­
mum permissible inflation pressure for that
tire .
Maximum loaded vehicle weight
means the sum of:
(a) Curb weight
(b) Accessory weight
(c) Vehicle capac ity weight, and
(d) Production opt ions weight
Ma ximum (permissible) inflation pressure
means the maximum co ld inf lation pressure
to which a tire may be inflated . Also called
"maximum inflation pressure."
Normal occupant weight
means 150 lbs. (68 k ilograms) times the
number of occupants seated in the vehicle up
to the tota l seating capacity of yo ur vehicle.
Occupant distribution
means distribution of occupants in a veh icle.
Outer diameter
means the overall diameter of an inflated new
tire .
Overall width
means the linear distance between the exteri­
ors of the sidewalls of an inflated tire, includ­
ing e levations due to labeling, decorations, or
protective bands or ribs .
Tires and wheels 22 7
Ply
means a layer of rubbe r-coated parallel cords.
Production options weight
means the combined weight of those installed
regular production opt ions we ighing over 5
lbs. (2.3 kg) in excess of those standa rd items
which they replace, not previously considered
in curb weight or accessory weight, including
heavy duty brakes, ride levelers, roof rack,
heavy duty battery, and special trim.
Radial ply tire
means a pneumatic tire in which the ply cords
that extend to the beads are laid at substan­
tially 90 degrees to the centerl ine of the
tread.
Recommended inflation pressure
see ~ page 226, Cold tire inflation pressure .
Reinforced tire
means a tire design to operate at higher loads
and at higher inflation pressures than the cor­
responding standard tire . Reinforced tires
may be identified as "XL", "xl", "EXTRA LOAD",
or "RF" on the sidewal l.
Rim
means a metal support for a tire or a tire and
tube assembly upon which the tire beads are
seated .
Rim diamete r
means nominal diameter of the bead seat. If
you change your wheel s ize, you wi ll have to
purchase new tires to match the new r im di­
ameter.
Rim size designation
means rim diameter and width.
Rim width
means nominal distance between rim flanges.
Sidewall
means that portion of a tire between the
tread and bead .
•
•
•

Emergency situations
General
This chapter is intended for trained emer­
gency crews and working personnel who have the necessary tools and equipment to
perform these operations.
Starting by pushing or
towing
(D Note
Vehicles with an automatic transmission
cannot be started by pushing or towing.
Starting with jumper
cables
If necessary, the engine can be started by
connecting it to the battery of another vehi­
cle.
If the engine should fail to start because of a
discharged or weak battery, the battery can be
connected to the battery of
another vehicle,
using a
pair of jumper cables to start the en­
gine.
Jumper cables
Use only jumper cables of sufficiently large
cross section to carry the starter current safe­
ly. Refer to the manufacturer's specifications.
Use only jumper cables with
insulated termi­
nal clamps which are distinctly marked :
plus(+) cable in most cases colored red
minus(-) cable
in most cases colored black.
A WARNING
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal
injury. Follow the instructions below for
safe handling of your vehicle's battery.
- Always shield your eyes and avoid lean­
ing over the battery whenever possible.
- A discharged battery can freeze at tem­
peratures just below 32 °F (0 °C). Before
Emergency situations 259
connecting a jumper cable, you must
thaw the frozen battery completely, oth­
erwise it could explode.
- Do not allow battery acid to contact eyes
or skin. Flush any contacted area with
water immediately .
- Improper use of a booster battery to start a vehicle may cause an explosion.
- Vehicle batteries generate explosive gas­
es. Keep sparks, flame and lighted ciga­
rettes away from batteries.
- Do not try to jump start any vehicle with a low acid level in the battery.
- The voltage of the booster battery must
also have a 12-volt rating. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged bat­
tery . Use of batteries of different voltage
or substantially different "Ah" rating
may cause an explosion and personal in­
JU ry.
- Never charge a frozen battery. Gas trap­
ped in the ice may cause an explosion.
-Never charge or use a battery that has
been frozen. The battery case may have
be weakened.
- Use of batteries of different voltage or
substantially different capacity (Ah) rat­
ing may cause an explosion and injury.
The capacity (Ah) of the booster battery
should not be lower than that of the dis­
charged battery.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
¢ page 210.
(D Note
-Applying a higher voltage booster bat­
tery will cause expensive damage to sen­
sitive electronic components, such as
control units, relays, radio, etc.
- There must be no electrical contact be­
tween the vehicles as otherwise current
could already start to flow as soon as the
positive(+) terminals are connected. ..,. •
•
•

260 Emergency situations
@ Tips
The disc har ged battery must be properly
connected to the ve hicle's electrical sys ­
tem. W hen jump starting or charg ing t he
battery, never connect the negative
grou nd cab le to the batte ry negat ive post
because the batte ry ma nager sys tem must
be ab le to detect th e ba ttery 's state o f
charge. A lways connec t the nega tive
grou nd ca b le to t he neg ative ground pos t
of the batte ry ma nager con trol unit.
Use of jumper cables
Make sure to connect the jumper cable
clamps in exactly the order described below!
Fi g. 178 Eng ine compar tment: conne ctors for jump
start cables a nd charger
CD
--0 > ~
F ig. 1 79 Jump start ing with the battery of a nother ve·
h ide: @-di scharge d veh icle battery, @-booster bat ­
te ry
The ba tte ry i s loca ted to the left in the eng ine
compartment.
Do not jump start a frozen or
thawed battery
¢ .&. in Starting wi th jumper
cables on page 259
! Replace the battery. The
p roced ure fo r connecting jump start cab les
that is described next is designed to he lp
jump start your vehicle.
Vehicle with discharged battery:
.,. Read t he followi ng car efully¢ page 259.
.,. Se t the parking brake an d place the selector
lever in the P position.
.,. Tur n the ignition and electr ica l equ ipment
off in both vehicles.
Connect POSITIVE(+) to POSITIVE(+ )
(red )
.,. To reach the battery terminals, flip the bat­
tery cover cap to the side¢
fig. 178.
1. Clamp the end of the red jump start cab le
to the term inal
(D ¢ fig. 179 on t he dead
batte ry @
¢ (Din Starting with jumper
cables on page 259.
2 . Clamp the othe r end of the re d jump start
c able to the termin al@ on the cha rging
b atte ry @ .
Connect NEGATIVE (-) to NEGATIVE(-)
(black)
3 . Clamp the bla ck end of the j ump st art ca­
b le
preferably at the ground point , or on
the nega tive te rmi na l® on the chargi ng
battery @.
4. Clamp the othe r black end of the jump
start cab le
only on the ground point@
on your vehicle @¢(D.
S. Route the jump start cab les so they can­
not get ca ught in the moving pa rts in the
engi ne compa rt m ent.
Starting the engine
6. Start the eng ine in the vehicle giving the
charge and let it run at idle.
7 . Start the eng ine in the vehicle with the
dead battery and wait two to three m i­
nutes until it "runs smoothly" .
8.
If t he eng ine does not s tart: Stop the
sta rting procedure after 10 second s and
t h en re p eat it after approximately 3 0 sec ­
onds .
9 . In the vehicle that is being jump started,
switch the heater fan and rear window de ­
froster on to reduce any voltage peaks
that may occ ur whe n disconn ecting the
jumpe r cables. The headlights must be
switched off.
IJI,