adding oil AUDI A3 2015 Owners Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2015, Model line: A3, Model: AUDI A3 2015Pages: 288, PDF Size: 71.46 MB
Page 26 of 288

24 Instruments and indicator lights
You may continue driving for the time being .
Check the oil level as soon as possible
¢ page 212.
-If the engine oil level is too low, add engine
oi l
¢ page 215.
-If the engine oil level is correct and the indi
cator light still turns on, drive at low engine
speed to the nearest authorized Audi dea ler
or qualified repair facility.
_..,. Engine oil sensor
II Oil level sensor: system fault!
The sensor to check the engine oil level has
failed. Drive to an authorized Audi dealer or
qua lified repair faci lity immediately to have
the malfunction corrected.
Q;) Note
Pay attention to the description in the
Owner 's Manual
¢ page 215 and
¢ page 215, Adding engine oil "l::;1:.
Bil Tank system
RD Please refuel
When the indicator light turns first turns on
and this message appears, the tank contains
the following amount of fuel:
- Front wheel drive : approximately 1.8 gal
lons (7 liters)
- All wheel drive: approximately 2.2 gallons
(8 .5 liters)
RD Fuel tank malfunction! Please contact
Service
If the indicator light turns on and this mes
sage appears, there is a ma lfunction in the
tank system.
Drive to your authorized Aud i dealer or quali
fied repair facility immediately to have the
malfunction corrected.
@) For the sake of the environment
Fuel should never enter the sewer system
or come into contact w ith the ground.
(D Tips
More information on refueling is available
on page ¢
page 207.
~ Washer fluid level
m Please add washer fluid
Fill the washer fluid with the ignition switched
off ¢
page 224.
• Windshield wipers
m Windshield wiper: system fault!
There is a malfunction with the windshie ld
wipers .
Drive to your authorized Audi dealer or quali
fied repair facility immediate ly to have the
malfunction corrected.
~ Defective light bulb warning
Applies to vehicles: wit h drive r info rmatio n system
If the S:i indicator light turns on, a bulb has
failed. The message ind icates the location of
the bulb .
Replace the bulb immediately.
Vehicle lights: system fault!
There is a malfunction in the headlights or
light switch. Drive to an author ized Audi deal
er or qualified repair facility immediately to
have the malfunction corrected.
_&. WARNING
- Light bulbs are under pressure and can
explode when bu lbs are replaced -risk of
inj ury.
- With gas-discharge lamps* (xenon head
lights), the high -voltage component
must be hand led appropriate ly. Other
wise, there is a risk of fatal injury.
-
Page 196 of 288

194 Driving and the environment
Driving through water
on roads
Note the following to avoid vehicle damage
when driving through water, for example on
flooded roads:
- The water must not be any higher than the
bottom of the vehicle body.
- Do not drive faster than wa lking speed.
A WARNING
After driving through water or mud, the
braking effect can be reduced due to mois
ture on the brake discs and brake pads. A
few careful brake applications should dry off the brakes.
@) Note
Vehicle components such as the engine, transmiss ion, suspension or electrical sys
tem can be severely damaged by driving
through water.
- Determ ine the depth before driving
through water.
- Do not stop the vehicle, drive in reverse
or switch the engine off when driving
through water .
- Keep in mind that oncoming vehicles may create waves that raise the water
level and make it too deep for your vehi
cle to drive through safely.
- Avoid dr iving through salt water (corro
s ion).
Catalytic converter
App lies to vehicles: with gasoline engine
It is very important that your emission con
trol system (catalytic converter) is function
ing properly to ensure that your vehicle is run
ning in an environmentally sound manner.
> Always use lead-free gaso line¢ page 206,
Fuel supply .
> Never run the tank down all the way to emp-
ty.
> Never put too much motor o il in your engine
¢ page 215, Adding engine oil
The catalytic converter is an efficient "clean
up" device built into the exhaust system of
the vehicle . The cata lytic converter burns
many of the pollutants in the exhaust gas be
fore they are released into the atmosphere.
The exclusive use of unleaded fuel is critica lly
important for the life of the catalytic convert
er and proper functioning of the engine.
A WARNING
-
The temperature of the exhaust system is high, both when driv ing and after stopping
the eng ine .
- Never touch the exhaust tail pipes once
they have become hot . This could result
in burns.
- Do not park or operate the vehicle in
areas where the hot exhaust system may
come in contact with dry grass, brush,
fue l spill or other material wh ich can
cause a fire.
- Do not app ly additional undercoating or
rustproofing on or near the exhaust manifold, exhaust pipes, catalytic con
verter or heat shields . Dur ing driving, the
substance used for undercoating could
overheat and cause a fire.
(D Note
- Be aware that just one tank filling with
leaded fuel will already seriously de
grade the performance of the catalytic
converter.
- Do not exceed the correct engine oil level
¢page 215.
-Do not drive until the fuel tank becomes
completely empty. The engine could mis
fire . Unburned fuel could also get into
the exhaust system and this cou ld cause
the catalytic converter to overheat.
- Do not switch off the ignition while the
vehicle is moving.
- Do not continue to operate your vehicle
under these conditions, as otherwise fuel
IIJ,,
Page 217 of 288

dealer has instructions about how to measure oil consumption accurately.
Checking the engine oil level
Fi g. 150 O il dip stick: O rienta ti on ass ist an ce for mea s·
ur ing t he oil leve l
Dete rmining th e oil l evel
• Park your vehicle on a level surface.
• Let the engine run in id le briefly while it is at
operating temperature and then shut the
engine off.
• Wait approximately two minutes .
• Remove the oil dipst ick. W ipe off the oil dip·
stick with a clean cloth and inse rt it all the
way in again.
• Remove the dipstick again and then read the
oi l level ¢
fig. 150 . Add more engine o il, if
necessary ¢
page 215.
Oil level in the G) area
• Do not add any o il.
Oil level in the @area
• You may add oil. After adding oil , the level
shou ld be in the@area.
Oil l evel in th e@ area
• You must add oil. After adding oil, the level
shou ld be in the@area.
D epending on the way the vehicle is driven
and the operating conditions, oil consumptio n
can be up to a 1/2 quart per 600 mi les
(0.5 liter per 1,000 km) . Consumption may be
h igher with in the first 3,000 miles (5,000
km) . Because of th is, the engine oil leve l must
be checked regularly . It would be best to
check each time you refue l your veh icle and
befo re long drives.
Che cking and Fillin g 215
Adding engine oil 'i=:1:
Fig. 151 E ng in e compa rtm en t: en gin e o il fil ler o pen ·
in g cover
• Tur n the engine off.
• Unscrew the engi ne oil filler opening cap
~ ¢ fig.151, ¢page 212, fig. 149 .
• Carefully add 0.5 q ua rts (0.5 liters) of the
appropriate oil¢
page 212 .
• After two m inutes check the oil leve l again
¢ page 215, Checking the engine oil level .
• Add oil, if necessa ry.
• Close the eng ine o il filler cap and push the
d ipstick al l the way in.
A WARNING
- When adding oil, do no t let o il drip o nto
hot engine components. There could be
ris k of a f ire.
- T he o il filler cap mus t be p roperly se·
cured to preven t oil from bei ng sprayed
on t he hot engine a nd exhaust system
when t he engine is running -fire haza rd!
- Always clean s kin th oroughly if it comes
into contac t with engine oil.
(D Note
- T he oil level cannot be above the@
range, beca use thi s ca n cause damage to
t he cat alytic conve rter or the engine .
Contact yo ur autho rize d Audi deale r o r
qualified repair facility to have excess oil
extracted if necessary.
- Do not mix any addit io na l lubr icants into
the engine oil. Damage cause by such ad·
ditives is not covered by the warranty .
1i1J>
Page 219 of 288

The cooling system has been filled at the fac
tory with a permanent coolant which does not need to be changed. The coolant consists of a
mixture of spec ia lly conditioned water and the
manufacturer's glycol-based coolant addi-
tive Gl3 antifreeze with anticorros ion addi
tives (50% fo r USA models; 60% for Canadian
models) . This mixture both assures th e neces
sary frost protect ion a nd p rotects me tal com
ponents in the engine 's coo ling system from
corrosion and scaling.
It al so raises the boil
ing po int o f the coo lant .
D o no t reduce the concentration of t he coo l
an t in the summer by ad ding plain w ate r.
The
proportion of coolant additive must be at
lea st 50 % but not more than 60%
to main
tain ant ifreeze protection and cooling efficien
cy. If the coolant frost protect ion is too low ,
the coolant cou ld free ze and damage the veh i
cle heating and eng ine cooling system.
F or yea r-round driv ing, antifreeze is added at
the facto ry for temperatures down to:
- -3 1 °F ( -3 5°C) USA
- -4 0°F ( -4 0°C) Canada.
If you must add coolant, use a m ixture of wa
ter and coolant addit ive. M ixing the coolant
addi tive wi th dist illed wate r is recom mend ed.
_& WARNING
Bef ore yo u check any thing in the e ngine
comp artme nt, alw ays re ad and hee d all
WARN INGS
¢page 210.
(D Note
- B efo re winter sets in, have the coolant
c hec ked to see if the c oolan t ad dit ive i n
you r vehi cle is su fficient t o mee t the cl i
mate cond itions. This is especially impor
tant if yo u live in a region whe re the win
ter is extremely cold. If necessary, in
crease the proport ion of coolant additive
to 60%.
- W hen addi ng coolant additive to your
cooling system, remember:
- We recommend using only coolant ad
ditive Gl2 ++ o r Gl3 ( check t he label)
-
Che cking and Fillin g 21 7
for you r vehi cle. This coolan t additive is
avai lab le at authorize d Audi dea le rs .
Ot her types of antifreeze ca n sig nifi
cantly reduce corros io n protection. The
res ulting corrosion can cause a loss of
coolant and serio us e ngine da mage .
- Do not add any type of rad iator leak seal
ant to you r vehicle's engine coolant .
Add ing radiator repair flu id may adverse
ly affect t he function and performanc e of
yo ur cooling sys tem and co uld resu lt i n
damage not covered by yo ur New Ve hicle
L imi ted W arranty.
Adding coolant
Fi g. 152 En gine co mpa rtment: markin gs on t he coo l
an t e xpan sio n t ank
Befo re you check a nyt hing in the eng ine com
partment ,
alway s read and heed all WARN
INGS ¢ page 210.
Checking the engine coolant level
.,. Park yo ur vehicle o n a level su rf a ce .
.,. Switch t he ignition off.
.,. Read t he coolant leve l on the coo lant expan
sion tank ¢
fig. 152. The coolant leve l must
be between the markings when the engine
in cold. When the engine is warm it can be
slightly above the upper mark ing .
Adding coolant
Req uirement : There m ust be a res idual
amount of coo lant in the expansion tank
c::> Q) .
.,. Le t the engine cool down.
.,. Place a clot h over the coo lant expans ion
tank cap a nd u nscrew the cap co unterclock-
wise
c::> _& . ..,.
Page 278 of 288

276 Index
E
ECO mode (automatic climate control sys -
tem) . ..... .. ................ ..... .. 67
EDL
refer to Electronic differentia l lock . .. . 185
Efficiency program . . . . . . . . . . . . . . . . . . . 28
Description . ...... .......... ... .. .. 28
Fuel economy messages . . . . . . . . . . . . . 29
Other equipment . . . . . . . . . . . . . . . . . . . 29
Electrical accessories
refer to Socket ............. .. .... .. 56
Electromechanical parking brake
refer to Parking brake ............... 76
Electromechanical steering .. .. .. .. .. . 189
I ndicator lights .......... .. .. .... . 189
Electronic differential lock ... .... .... . 185
Indicator light . . . . . . . . . . . . . . . . . . . . . 22
Electronic immobilizer ....... ... .... .. 36
also refer to Immobilizer . . . . . . . . . . . . 31
E lect ronic interaxle differential lock .... 185
Electronic speed limiter ..... .. .. .. .. . . 30
Electronic stabilization control (ESC)
Indicator light . . . . . . . . . . . . . . . . . . . . . 22
Electronic Stabilization Control (ESC) ... 185
Emergency assistance .......... .... . 246
Emergency flasher .......... ... .... .. 43
Emergency flashers
I ndicator light . . . . . . . . . . . . . . . . . . . . . 25
Emergency operation Emergency braking function .. .. .. .. . . 78
Front passenger's door/rear doors . . . . . 3 7
L uggage compartment lid ........ .. . 246
Panorama sunroof ........ .. .. ...... 41
with conven ience key .... .. .. .. .. .. . . 75
Emergency release Fuel filler door .............. ... ... 209
Selector lever . . . . . . . . . . . . . . . . . . . . . 112
Emergency starting ........ .. .. .. .. . 259
Emergency towing ......... .. .. .. .. . 261
Energy management . . . . . . . . . . . . . . . . 190
Indicator light . . . . . . . . . . . . . . . . . . . . . 20
Engine Coolant .. .. ..................... . 216
Starting with jumper cables .... .... . 259
starting (button) . .. ...... .. .. .. .. . . 73 Starting (driver messages with conven-
ience key) ..... .. ................ .. 75
starting (key) . ... ................ .. 70
stopping (button) ............. ..... 74
stopping (key) ................ ..... 72
Engine compartment
Closing the hood . . . . . . . . . . . . . . . . . . 211
Opening the hood ................ . 211
Overview .. .... .. ... .......... .... 212
Safety precautions ............... .. 210
Engine control (indicator light) . . . . . . . . . 23
Engine coolant .. .. .......... ... .. .. 216
Radiator fan ... .. ... .......... .... 218
Engine oil .. ................... .... 212
adding . .. .. .. .. ... .......... .... 215
Changing . ...... ... ......... ... .. 216
Checking the oil level ... ..... ... .. .. 215
Dipstick... .. .. .. .... .... .... 212, 215
Indicator light .................... . 20
Oil consumpt ion .. ............. .. .. 214
Oil grades ..... .. ............. .... 212
Specification and viscosity ........ ... 212
Use ..... ..... .. .. .............. . 215
Engine speed limitation ( indicator light) . 23
Environment Break -in per iod . .. ... ....... ... .. .. 193
Catalytic converter ....... ...... .. .. 194
Disposing of your vehicle battery ..... 223
Driving at high speeds .......... .... 195
Driving to minimize pollution and noise 195
Fuel economy .... ................ . 195
Letting the vehicle stand and warm up . 196
Proper disposal of drained brake fluid . 219
Proper disposal of drained engine oil .. 216
Unleaded fuel .... ... .......... .... 206
What should I do with an old battery? . 223
EPC (engine control) ................ .. 23
ESC Electronic stabilization control ... .. .. 185
Post-coll is ion brake assist ..... .. .. .. 186
Sport mode ... .. ................ . 187
ESP
refer to ESC ... .. ..... ..... ... .. .. 185
Event Data Recorder (EDR) ............ 185
Exhaust tail pipes cleaning ........... 202
Exterior lighting ... ..... ..... ... .. .. . 42