engine AUDI A3 CABRIOLET 2016 Manual Online
[x] Cancel search | Manufacturer: AUDI, Model Year: 2016, Model line: A3 CABRIOLET, Model: AUDI A3 CABRIOLET 2016Pages: 272, PDF Size: 67.88 MB
Page 244 of 272
Emergency situations
Emergency situations
General
This chapter is intended for trained emergency crews and working personnel who have the nec
essary tools and equipment to perform these
operations.
Starting by pushing or
towing
CD Note
Vehicles with an automatic transmission can
not be started by pushing or towing.
Starting with jumper
cables
If necessary, the engine con be started by con
necting it to the battery of another vehicle .
If the engine should fail to start because of a dis
charged or weak battery, the battery can be con
nected to the battery of
another vehicle, using a
pair of jumper cables to start the engine.
Jumper cables
Use only jumper cables of sufficiently large cross
section
to carry the starter current safely. Refer
to the manufacturer's specifications.
Use only jumper cables with
insulated terminal
clamps which are distinctly marked :
plus(+) cable in most cases colored red
minus(-) cable
in most cases colored black .
A WARNING
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal in
jury. Follow the instructions below for safe hand Ling of your vehicle's battery .
-Always shield your eyes and avoid leaning
over the battery whenever possible.
-A discharged battery can freeze at tempera
tures just below 32 °F (0 °C). Before con
necting a jumper cable, you must thaw the
244
frozen battery completely, otherwise it could explode .
- Do not allow battery acid to contact eyes or
skin. Flush any contacted area with water immediately.
- Improper use of a booster battery to start a
vehicle may cause an explosion.
- Vehicle batteries generate explosive gases.
Keep sparks, flame and lighted cigarettes
away from batteries.
- Do not try to jump start any vehicle with a
low acid level in the battery .
- The voltage of the booster battery must also
have a 12-volt rating. The capacity (Ah) of
the booster battery should not be lower
than that of the discharged battery. Use of
batteries of different voltage or substantial
ly different "Ah" rating may cause an explo
sion and personal injury .
- Never charge a frozen battery. Gas trapped in the ice may cause an explosion .
- Never charge or use a battery that has been
frozen . The battery case may have be weak
ened .
- Use of batteries of different voltage or sub stantially different capacity (Ah) rating may
cause an explosion and injury. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged battery.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
~page 188.
CD Note
-Applying a higher voltage booster battery
will cause expensive damage to sensitive
electronic components, such as control
units, relays, radio, etc.
- There must be no electrical contact between
the vehicles as otherwise current could al
ready start to flow as soon as the positive
(+) terminals are connected.
@ Tips
The discharged battery must be properly con-
nected to the vehicle's electrical system. .,..
Page 245 of 272
<( co ..... N
" N ..... 0
" > 00
When jump starting or charging the battery,
never connect the negative ground cable to
the battery negative post because the battery
manager system must be able to detect the
battery's state of charge . Always connect the
negative ground cable to the negat ive ground
post of the battery manager control unit .
Using jump start cables
Connect the jump start cables in the exact order
described below.
Fig . 190 Engine compa rtment: connec tor s for ju mp start
cab les and a charger
Fig. 191 Jump start ing th e battery w ith another vehicle:
@ -dra ined bat tery, @-sta rter battery
m ~ 0 :> m
m
The battery is located to the left in the engine
compartment.
Do not jump start a frozen or
thawed battery
c> A in Starting with jumper ca
bles on page
244! Replace the battery. The pro
cedure for connecting jump start cables that is
described next is designed to help jump start
your veh icle.
Vehicle with drained battery:
.. Read the following carefully
c> page 244
.. Set the parking brake and place the selector
lever in the P position .
Emergency situations
.. Turn the ignition and electrica l equipment off
in both vehicles .
Connecting the negative terminal(-) to the
negative terminal(-) (black)
.. To reach the battery terminals, flip the battery
cover cap to the side
c> fig. 190.
1. Clamp the end of the red jump start cable to
the terminal
(D c> fig. 191 on the dead bat
tery @
c> CD in Starting with jumper cables
on page 244 .
2. Clamp the other end of the red jump start ca
ble to the terminal @on the charging bat
tery @.
Connect NEGATIVE (-) to NEGATIVE (-)
(black)
3. Clamp the black end of the jump start cable
preferably at the ground point, or on the
negative term inal @ on the charging battery
®·
4. Clamp the other end of the black jump start
cable
only to the ground point© on your
vehicle @Q(D.
5. Route the jump start cables so they cannot
get caught in the moving parts in the engine
compartment.
Starting the engine
6. Start the engine in the vehicle giving the charge and let it run at idle.
7. Start the engine in the vehicle with the dead battery and wait two to three minutes until it
"runs smoothly" .
8.
If the engine does not start, stop the start ing
procedure after 10 seconds and then repeat
it after approx imately 30 seconds.
9. In the vehicle that is being jump started,
switch the heate r fan and rear window de
froster on to red uce any voltage peaks that
may occur when disconnecting the jumper
cables. The headlights must be switched off.
10. With the engines running, remove the cables in
reverse order of the way they were instal
led . Make sure the cables do not get caught
in moving eng ine components .
11. Switch the heater fan and rear window de
froster off.
12 . Close the battery cover.
245
Page 246 of 272
Emerg enc y s it uati ons
The battery is vented to the outside so that not
gases enter the passenger compartment. Make
sure that the connected posit ive termina l clamps
on the jump start cable have sufficient contact
with metal.
A WARNING
Follow the warnings and instructions from
the jump start cable manufacturer to reduce
the risk of ser ious injuries and vehicle dam
age. If you are unsure about anything, call
roads ide assistance .
- The jump start cables must be long enough
so that the vehicles do not touch .
-
-Route the jump start cables so they cannot
get caught in the moving parts in the engine
compartment.
- Always read and follow the warnings before
che ck ing anything in the engine compart
ment
¢page 188.
(D Note
Connecting jump start cables incorrectly can
destroy the alternator .
- Always connect the positive terminal(+) to
the positive term inal( +) and the negative
terminal(-) to the negat ive termina l(-) on
the body ground po int, but not the negative
terminal on the battery.
- Make su re the screw pl ugs on the batte ry
ce lls are installed securely.
If not, tighten
the plugs before connecting the clamps to
the negat ive termina l on the battery .
- Please no te that the connecting p ro cess de
scribed below for the jump start cab les is in
tended for when your vehicle is being jump
started . If you are j ump starting another ve
hicle, do not connect the negative cable to
the negat ive termina l(·) on the drained
battery, but rather connect it to a large
metal component that is bolted secu rely to
the engine block, o r to the engine block it
se lf. If the battery in the vehicle being jump
started is no t vented to the o uts ide , the re is
a risk of exp losion due to hydrogen gas .
-Make su re that the conne cted positive te r
minal clamps have s ufficient contact with
me tal.
246
- Do not use the battery negative terminal for
jump starting or a ma lfunction cou ld occur
in the vehicle electrical system.
Towing with a tow truck
General hints
Your Audi requires special handling for towing .
The following information is to be used by com
merc ial tow truck operators who know how to op
erate their equipment safely .
-Never to w yo ur Audi. To w ing will cause d am ·
a ge to the engine and t ran sm ission.
- Never wrap the safet y chains or winch cable s
a roun d the brake l ines .
- To pre vent un nece ssary damage , your Audi
must be t ran sported with a flat bed tru ck.
- To l oad the vehicle on to the flat bed , use the
towing loop found in the vehicle tools and at
t ac h to the fro nt or re ar ancho rage
¢ page 247 and ¢ page 247.
A WARNING
A vehicle being towed is not safe for passen
gers . Never allow anyone to ride in a vehicle
being towed, for any reason .
Page 249 of 272
<( co .... N ,.__
N .... 0 ,.__
> co
distr ibut ion an d ba lance . This might hap
pen, for exam ple, when heavy compo
nents such as the engine b lock or trans
miss io n are removed.
- When removing heavy components like
th ese, anc hor vehicle t o hoist o r add corr e
sponding weights to maintain the center of
grav ity. Oth erwise, the ve hicle might ti lt or
s li p off the hois t, causing s eriou s perso na l
lnJUry.
(D Note
- Be awar e of the fo llowing poi nts before lift
i ng t he vehicle:
- The vehicle should never be lifted or
jacked up from underneath the engine oil pan , the transmission housing, the front
or rear axle or the body side members .
This could lead to serious damage.
- To avoid damage to the unde rbody or
chassis frame, a rubber pad must be in
serted between the floor jack and the lift
points.
- Before driv ing over a workshop hoist,
check that the vehicle weight does not
exceed the permissible lifting capacity of
the hoist .
- Before driving over a workshop hoist, en
sure that there is sufficient clearance be
tween the hoist and low parts of the ve
hicle.
Emergency situations
249
Page 250 of 272
Technical data
Technical data
Vehicle identification
Fig. 199 Vehicle Ident if ication Numbe r (VlN) plate : loca·
tio n on d river 's side dash panel
XXXXX XX -X -XX XX XXX XX
@-+ ~J:~t::1 ::: xxxxxxxx xx x xxxx xxx x
IYP lf'VPE XXX X XX
XX XXXXXXX XX X X XX
XXX KW XXX
\YT IM:.COll/fAANS ,COOE XXX XXX 15\_L I MOIOlll
@-+ ~~
1
:tr:~i XXXX I XXXX XXX I XX
II. -AUSST . / OPTIO NS
E0 A 7D5 4UB 6X
M SSG SR W
2EH JOZ lLB lAS
lBA
3FC SM U 7 X1
F0 A
9G3 0
G7 0Y H
0JF
TL 6 3 KA 8EH UlA X 9B Q
Z7
1 XW
803 908
824 020
7T6 C V7 7 K0 4X3 2K2
3L4 4KC 3Y0 413
502
lS A 7GB 01A
4G0
XX X XX X
XX X xxxx
Fig. 200 The vehicle ide ntifi cat ion l abel - inside t he lug ·
gage compartment
Vehicle Identification Number (VlN)
The Vehicle Identification Number is located in
different places :
- under the windshield on the driver's side
¢fig . 199.
- in the MMI: Select: the I MENU I button> Car>
Systems*
control button > Service & control >
VIN number .
-on the vehicle identification label.
250 Vehicle
identification label
The vehicle identification label is located in the
luggage compartment in the spare wheel well.
The label
9 fig. 200 shows the follow ing vehicle
data:
(D Vehicle Identif ication Number (VIN)
@ Vehicle type, engine output, transmission
@ Engine and transmission code
@ Paint number and interior
® Optional equipment numbers
The information of the vehicle identification label
can also be found in your Warranty
& Mainte ·
nance booklet.
Safety compliance sticker
The safety compliance sticker is your assurance
that your new veh icle complies with all applicable
Federal Motor Vehicle Safety Standards which
were in effect at the time the vehicle was manu
factured. Yo u can find this sticker on the door
jamb on the driver's side. It shows the month and
year of production and the vehicle identification
number of your vehicle (perforation) as well as
the Gross Vehicle Weight Rating (GVWR) and the Gross Axle We ight Rating (GAWR).
High voltage warning label
The high voltage warning label is located in the
engine compartment next to the engine hood re
lease. The spark ignition system complies w ith
the Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for front
and rear are listed on a sticker on the door jamb
on the driver 's side.
The Gross Vehicle Weight Rating includes the
weight of the basic vehicle plus full fuel tank, oil
and coolant, plus maximum load, which includes
passenger weight (150 lbs/68 kg per designated
seat ing position) and luggage weight¢,&. . .,.
Page 252 of 272
Tech nical data
Gasoline engines
A3 Cabriolet 1.8, 4 cylinder
Maximum output SAE net hp@ rpm
Max imum torq ue SAE net lb-ft@ rpm
Displacement CID (cm
3
)
Engine oil with filter change1>
Fuel ¢ page 184, Gasoline fuel
A3 Cabriolet 2.0, 4 cylinder
Maximum output SA E net hp@ rpm
Maximum torque SAE net lb
-ft @ rpm
Displacement CID (cm
3
)
Engine oil with fi lter change1
)
Fuel ~ page 184, Gasoline fuel
ll For specific engine oil capac ities, please see
the most current information fo r th e USA at
ht tp :/ /www .aud iusa.com/help/ma intenance o r
for Canada at http://www.aud i.ca/ca/b rand/ en/
your _aud i/ aud i _services _a nd/Ca re _and _M a i nte
n a nce/ schedu le.htm l or call 800-822-2834.
252
170 @ 4500 -6200
200@ 1600 -4400
110 (1798)
220 @ 4500 -6200
258@ 1600 -4400
121 (1984)
Page 253 of 272
<( co .... N r--N .... 0 r--> co
Consumer information
Warranty coverages
Y our Audi is co vered b y the foll owing war ran
tie s:
- New Vehicle Limited Warranty
- Limited Warranty Against Corrosion Perfora-
tion
- Emissions Control System Warranty
- Emissions Performance Warranty
- California Emissions Control Warranty (USA
vehicles only)
- California Emissions Performance Warranty
(USA vehicles only)
Detailed information regard ing your warranties
can be found in yo ur
W arranty & M ainten ance
bookl et.
Operating your vehicle
outside the U.S.A. or
Canada
Government reg ulations in the Un ited States and
Canada require that automobiles meet specific
emission regulations and safety standards.
Therefore, vehicles built for the U .S.A. and Cana
da differ from vehicles sold in other countries.
I f you p lan to take your vehicle outside the conti
nenta l limits of the United States or Canada,
there is the poss ibility that:
- u nleaded fue ls for vehicles with cata lytic con
verter may not be available;
- fuel may have a considerably lower octane rat
i ng . Imprope r fuel may ca use engine damage;
- service may be inadequate due to lack of p roper
service facilities, tools or testing eq uipment;
- r eplacement parts may not be readily ava ilable.
- Navigation systems for veh icles built for the
U .S .A . and Canada will not necessa rily work in
E urope, and may not wo rk in other countries
outside No rth Ame rica.
Con sumer inf ormation
(D Note
Audi cannot be respons ible for mechanical
damage that could resu lt from inadequate
fuel, service or parts ava ilability.
Audi Service Repair
Manuals and Literature
Audi Official Factory Service Manuals and L itera
ture are published as soon as poss ible after mod
el introduction. Service ma nuals and literature
are avai lab le to order from the Audi Tec hni cal Lit
erature Ordering Center at :
www.audi .t e chlit eratur e.com
Maintenance
General
Your vehicle has been designed to he lp keep
maintenance requirements to a min imum. How
ever, a certain amount of regular maintenance is
still necessary to assure your veh icle's safety,
economy and reliab ility . For detailed vehicle
maintenance consult your Wa rranty
& Mainte
nance book let .
Und er diff icult op erating condition s, for exam
ple at extremely low outside temperatures, in
very dusty regions, when towing a trai le r very fre
quently, etc., some service work shou ld be per
fo rmed between the in terv als specified. This ap
plies particularly to:
- oil changes , and
- cleaning or replacing the a ir filter .
(® For the sake of the environment
By regularly maintain ing your vehicle, you
help make sure that emiss ion standards are
maintai ned, thus min imizing adverse effects
on the environment .
Important considerations for you and your
vehicle
The increasing use of electronics, sophisticated
fuel injection and emission control systems, and
the generally increas ing technica l complexity of ""'
253
Page 254 of 272
Consumer inf orm ation
today's a utomo biles, have steadily re duced the
scope of maintenance and repairs whic h can be
carried out by veh icle owners.
Also , sa fet y and
en vironmental
concerns place very strict limits
on the nature of repairs and adjustmen ts to en
g ine and transmission parts wh ich an owner can
perform .
Maintenance, adjustments and repairs usually re
qu ire special tools, testing devices and other
equ ipment available to specially trained work
shop personnel in order to assure proper per
forma nce, re liability and safety of the veh icle and
its many systems .
Improper maintenance, adjustments and repairs
can impair the operation and reliab ility of your
ve hicle and eve n void your vehicle warranty .
Therefo re, proof of se rvicing in a ccordance w ith
the m aintenance sched ule may be a condition for
up ho ld ing a possible wa rranty claim made within
the wa rranty pe riod.
Above all , ope rational safety can be adversely af
fected, cre ating unne cessa ry risks fo r you and
your passengers.
I f in doubt about any servicing, have it done by
your author ized Audi dealer or any other properly
eq uipped and qualified workshop . We strongly
urge you to g ive your author ized Audi dealer the
opportunity to perform a ll scheduled mainte
nance and necessa ry repairs. Your dealer has the
facilities, origina l parts and tra ined specialists to
keep your veh icle runn ing properly.
P e rforming limited maintenance yourself
The fo llow ing pages describe a limited number of
procedures whic h can be performed on your vehi
cle with ordinary tools, should th e need arise and
tra ined personnel be unava ilable. Before per
forming any of these procedures, always thor
ough ly read all of the app licab le text and carefu l
ly follow the instructions g iven . A lways rigorously
observe the
WARNINGS prov ided .
Befo re yo u check anything in the engine com
partment, always read and heed all WARNINGS
c::> & and c::> page 188 .
254
A WARNING
-
-Ser ious personal in jury may occur as a result
of imp roperly performed maintenance, ad
justments or repairs .
- Always be extreme ly careful when work ing
on the vehicle . Always follow commonly ac
cepted safety practices and general com mon sense. Never r is k personal in jury.
- Do not attempt any of the mainte nance,
checks or repairs described on the following pages if you are no t fu lly fam iliar with these
or other proce dures with respect to the ve
hicle, o r are uncert ain how to p ro ceed.
- Do not do any work wi thout the prope r tools
a nd equi pmen t. H ave the necess ary wo rk
done by your authorized Au di dealer or an
other properly equipped and qualified work
shop.
- The engine compartment of any motor vehi
cle is a potentially hazardous area . Never
reach into the a rea around or touch the radi
ator fan. It is temperature controlled and
can switch on suddenly - even when the en
gine is off . The radiator fan switches o n au
tomatically when the coolan t reaches a cer
tain tempe ra ture an d w ill cont inue to run
until the coolant tem pe rature d rops.
- Always sw itch off the ignition before anyone
gets under the vehicle.
- Always support your vehicle with safety
stands if it is necessary to work underneath
the vehicle. The jack supp lied wi th the veh i
cle is no t adequate fo r thi s pu rpose a nd
could collapse causing serious personal in
Jury .
- If you must wor k unde rneath the vehicle
w ith the wheels on t he g roun d, always make
sure the vehicle is on level ground, that the
wheels are always sec urely blocked and that
the engine cannot be started.
- Always make sure the transmission se lector
lever (automatic t ransm iss ion) is in P (Park
position) and the pa rk b rake is applied. ..,
Page 255 of 272
<( co .... N ,.__
N .... 0 ,.__
> co
@ For the sake of the environment
-Changing the engine settings will adversely
affect emission levels. This is detrimental to
the environment and increases fuel con
sumption.
-Always observe environmental regulations
when disposing of old engine oil, used brake
fluid, dirty engine coolant, spent batteries
or worn out tires.
- Undeployed airbag modules and pretension
ers might be classified as Perchlorate Mate
rial -special handling may apply, see
www .dtsc.ca.gov/hazardouswaste/perchlo
rate . When the vehicle or parts of the re
straint system including airbag modules
safety belts with pretensioners are scrap
ped, all applicable laws and regulations
must be observed. Your authorized Audi
dealer is familiar with these requirements
and we recommend that you have your deal er perform this service for you.
Accessories and
technical changes
Additional accessories and parts replacement
Always consult an authorized Audi dealer before
purchasing accessories.
Your vehicle incorporates the latest safety design
features ensuring a high standard of active and passive safety.
This safety could be compromised by non-ap proved changes to the vehicle. For this reason, if
parts have to be replaced, please observe the fol
lowing points when installing additional accesso
ries:
Approved Audi accessories and genuine Audi parts are available from authorized Audi dealers.
These dealers also have the necessary facilities, tools and trained specialists to install the parts
and accessories properly .
Consumer information
A WARNING
Using the wrong spare parts or using non-ap
proved accessories can cause damage to the
vehicle and serious personal injury.
- Use only accessories expressly approved by
Audi and genuine Audi spare parts
- These parts and accessories have been spe
cially designed to be used on your vehicle.
- Never install accessories such as telephone
cradles or beverage holders on airbag covers
or within the airbag deployment zones. Do
ing so will increase the risk of injury if air
bags are triggered in an accident!
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS 9page 188.
(D Note
-If items other than genuine Audi spare
parts, add-on equipment and accessory
items are used or if repair work is not per
formed according to specified methods, this
can result in severe damage to your vehi
cle's engine and body (such as corrosion)
and adversely affect your vehicle's warranty.
- If emergency repairs must be performed
elsewhere, have the vehicle examined by an
authorized Audi dealer as soon as possible.
- The manufacturer cannot be held liable for
damage which occurs due to failure to com
ply with these stipulations.
Technical Modifications
Our guidelines must be complied with when tech
nical modifications are made.
Always consult an authorized Audi dealer
before
starting work on any modifications.
This will help ensure that vehicle function, per
formance and safety are not impaired
9 ,& .
Attempting to work on electronic components
and the software used with them can cause mal
functions. Because of the way electronic compo
nents are interconnected with each other, such
malfunctions can also have an adverse affect on
other systems that are not directly involved. This ..,.
255
Page 259 of 272
<( co .... N ,.__
N .... 0 ,.__
> co
Remote control key . . . . . . . . . . . . . . . . . . . 29
Safety central locking . . . . . . . . . . . . . . . . . 32
Sett ing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Certification . . . . . . . . . . . . . . . . . . . . . . . . . 256
Changing engine oil . . . . . . . . . . . . . . . . . . . 194
Child restraints Danger of using child restraints in the front
seat... .. .. .. ............... .. ..... 144
Where can I get additional information
about child restraints and their use? . . . . 183
Child restraint system anchors . . . . . . . . . . 179
Child safety . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Important safety instructions for using chi ld
safety seats . . . . . . . . . . . . . . . . . . . . . . . . 169
Teth er anchors . . . . . . . . . . . . . . . . . . . . . . 181
Tether straps . . . . . . . . . . . . . . . . . . . . . . . 181
Child safety seats Booster seats . . . . . . . . . . . . . . . . . . . . . . . 17 4
Convertible ch ild seats . . . . . . . . . . . . . . . 172
Convertible locking retractor . . . . . . . . . . 177
How do I properly install a child safety seat
. h' l 7 169 in my ve rc e . ................. ..... .
Infant seats .. .. ............. .. .. .. . 171
Installing a child restraint using the LATCH
system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
LATCH system . . . . . . . . . . . . . . . . . . . . . . 180
L ower anchorages . . . . . . . . . . . . . . . . . . . 180
Mounting and releasing the anchorage
hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
Safety instructions . . . . . . . . . . . . . . . . . . . 169
Unused safety belts on the rear seat . . . . 171
Child seats . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Securing . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Cleaning/remov ing ice from windows . . . . . 226
Cleaning Alcantara . . . . . . . . . . . . . . . . . . . . 227
Cleaning artificial leather. . . . . . . . . . . . . . . 227
C leaning carbon parts . . . . . . . . . . . . . 226 , 227
Cleaning controls . . . . . . . . . . . . . . . . . . . . . 226
Cleaning decorative parts and trim . . . . . . . 226
Cleaning displays . . . . . . . . . . . . . . . . . . . . . 226
Cleaning exhaust tail pipes . . . . . . . . . . . . . 225
C lean ing plast ic parts . . . . . . . . . . . . . . . . . . 226
Clea ning seat covers . . . . . . . . . . . . . . . . . . . 227
C leaning tai l lights . . . . . . . . . . . . . . . . . . . . 225
C lea ning textiles . . . . . . . . . . . . . . . . . . . . . . 227
Cleaning the rims . . . . . . . . . . . . . . . . . . . . . 225
Index
Cleaning the wind deflector . . . . . . . . . . . . . 226
Climate control system Key recognition . . . . . . . . . . . . . . . . . . . . . . 61
Climate control system (automatic)
Adjusting air vents . . . . . . . . . . . . . . . . . . . . 63
Adjusting the air vents . . . . . . . . . . . . . . . . . 63
Air distribution, air vents . . . . . . . . . . . . . . . 63
AUTO (cl imate control system) . . . . . . . . . . 62
Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
D efrosting the windshield . . . . . . . . . . . . . . 63
Drive select . . . . . . . . . . . . . . . . . . . . . . . . . 106
Rear window defogger . . . . . . . . . . . . . . . . . 64
Recirculation mode . . . . . . . . . . . . . . . . . . . 63
Setting the temperatu re . . . . . . . . . . . . . . . 62
synchroniz ing . . . . . . . . . . . . . . . . . . . . . . . . 62
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Clos ing
Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
Windows . .. .. .. .. ............. .. .. . 34
Closing/ope ning
by remote control . . . . . . . . . . . . . . . . . . . . 29
with the central locking switch . . . . . . . . . . 31
with the conven ience key . . . . . . . . . . . . . . . 30
Cockp it (overview) . . . . . . . . . . . . . . . . . . . . . . 8
Coming home . . . . . . . . . . . . . . . . . . . . . . . . . 45
Compartments . . . . . . . . . . . . . . . . . . . . . . . . 57
Compass in the mirror . . . . . . . . . . . . . . . . . . 51
Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . 256
Consumer information . . . . . . . . . . . . . . . . . 253
Consumer Information . . . . . . . . . . . . . . . . . 132
Consumption (fuel) . . . . . . . . . . . . . . . . . . . . 24
Contacting NHTSA . . . . . . . . . . . . . . . . . . . . 132
Conv enience key
Emergency operation . . . . . . . . . . . . . . . . . . 72
Indicator light . . . . . . . . . . . . . . . . . . . . . . . 72
Starting the engine (S TART ENGINE STOP
button) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Stopping the engine (START ENGINE STOP
button) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Switching the ignition on . . . . . . . . . . . . . . 70
unlocking/lock ing . . . . . . . . . . . . . . . . . . . . 30
Convenience opening/closing . . . . . . . . . . . . 34
Convert ible child safety seats . . . . . . . . . . . 172
259