wheel AUDI A3 SEDAN 2018 Owner's Manual

Driving
,.. Remove the ignition key in position @
9 page 76, fig. 85 9 ,&..
,.. Turn the steering wheel until you hear the
steering wheel lock.
The locked steering helps prevent vehicle theft.
A WARNING
- Never turn off the engine before the vehicle
has come to a complete stop. The full func­
tion of the brake booster and the power
steering is not guaranteed. You must use more force to turn or brake . Because you
cannot steer and brake as you usually
would, this co uld lead to accidents and seri-
. . . ous mJunes .
-Never remove the ignit ion key from the ign i­
t ion loc k while the vehicle is moving. Other­
wise, the steering lock could suddenly en­
gage and you would not be able to steer the
vehicle.
- If you leave the veh icle, switch the ignit ion
off and take the vehicle key with you. Other­
wise, the engine could be started or electri­
cal equipment such as the power windows
could be operated. This can lead to serious
injury.
- For safety reasons, always park the vehicle
with the selector lever in the P position.
Otherwise, there is the risk that the vehicle
could roll unintentionally .
(D Note
If the engine has been under heavy load for
an extended period of t ime, heat builds up in
the engine compartment after the engine is
switched off and there is a risk of damaging
the engine . For this reason, let the engine run
for at idle
for approximately two minutes be­
fore shutting it
off.
@ Tips
For up to 10 minutes after stopping the en­
gine, the radiator fan may turn on again auto­
matically or it may continue to run (even if
the ignition is sw itched
off) for the following
reasons:
76
- The coolant temperature is increasing due
to trapped heat.
- If the engine is warm and the engine com­
partment also heats up from strong sun­
light.
Starting and stopping
the engine (vehicles with
convenience key)
Starting the engine
App lies to : vehicles wit h co nvenience key
The I START ENGINE STOP I button switches the
ignition on and starts the engine.
Fig. 85 Center conso le: STAR T ENGINE ST OP button
Plug-in hybrid drive*: refer to the information for
start ing the veh icle under
9 page 94.
Starting the engine
.,. Press the brake pedal and move the selector
lever to the "P" or "N" position .
.,. Press the I START ENGIN E STOP I button briefly .
The engine will start.
Equipment that uses a lot of electricity is switch­
ed
off temporarily when you start the engine .
If the engine does not start immediately, stop
the starting procedure by pushing the
I START ENGINE STOP! button again and repeat
after 30 seconds .
Switching the ignition on/off
If you would like to switch the ignition on with­
out starting the engine, follow these steps:
.,. Press the I ST AR T ENGINE ST OP ! button with-
out
pressing the brake pedal. Vehicles without .,,.

u. 00 .-< N l'­ N .-< 0 N > 00
the Start/Stop system*: the needle in the
tachometer moves into the
READY position .
~ To switch the ign ition off, press the button
again. The needle in the tachome ter moves into
the
OFF posit ion.
If the
,:rM i ndicator light b links and the message
Please turn steering wheel appears when switch­
ing the ign ition on, the steer ing lock has been en­
g aged . In this case, turn the steering wheel
slig htly to the left or right .
Start/St op sy stem*
See the information in <=!) page 79, Start/Stop
system.
A WARNING
To red uce the risk of poisoning, never allow
the engine to run in confined spaces.
@ Note
Avoid hig h engine speed, full throttle, and
heavy engine load if the engine has not reached operating temperature yet. You could
damage the engine.
@) For the sake of the environment
Do not let the engine run whi le parked to
warm up. Begin driving immediately . This re­
duces unnecessary emissions.
(D Tips
- Some noise after starting the engine is nor­
mal and is no cause for concern.
- If you leave your ve hicle with the ignition
switched on, the ignition will switch off af­
ter a certa in amount of t ime. Make sure that
electr ical equ ipment s uch as the exter ior
li ghts are sw itched off.
Stopping the engine
Applies to: vehicles with convenience key
-
Plug-in hybrid dr ive*: refer to the informat ion un­
de r
<=!) page 94.
~ Bring the vehicle to a ful l stop .
ll This fun ctio n is not a vail abl e in a ll co untries.
Driving
~ Move the selector lever into t he P posit ion .
~ Press the !S T AR T ENGINE ST OP ! button
<=!)page 76, fig . 85 .
Steering lock1>
The steer ing locks when yo u tur n the eng ine off
u sing the
!S TAR T ENG INE S TOPI* button, move
the se lector lever into the P position and open
the driver's door. The locked steering helps pre ­
vent vehicle theft .
Emergency off function
If it i s absolutely necessa ry , the eng ine c an also
be turned off wh ile d riving at speeds starting at
4 mph (7 km/h) . To switch the engine off, press
the
I S T AR T ENGINE STOPI button twice in a row
briefly or press and ho ld for longer than two sec­
onds.
A WARNING
--
- Never turn off the eng ine before the vehicle
has come to a complete stop . The full func ­
tion of the brake booste r and the power
steer ing is not guaranteed. You must use
mo re fo rce to t urn o r bra ke. Be ca u se you
can not stee r and br ake as yo u usually
wo uld, this could lead to acc idents and seri ­
ous injuries .
- I f you leave the vehicle, sw itch the ignition
off and take the ve hicle key wi th yo u. Other ­
wise, the engine could be started or e lectri ­
cal equipment such as the power windows
could be operated . This can lead to serious
injury .
- For safety reasons, always park the vehicle wit h the selector lever in the P pos ition.
Otherw ise, there is the risk that the vehicle
could roll unintentiona lly .
@ Note
If the engine has been under heavy load for
an extended period of time, heat builds up in
the eng ine compartment after the engine is
switched off and there is a r isk of damag ing
the e ng ine . Fo r thi s reason, let the e ng ine run
.,.
77

Drivin g
~ Brake the vehicle to a stop . The engine stops
shortly before the vehicle comes to a stop or if
the ve hicle is stationary
1>. Keep your foot on
the brake pedal. The
D] ; D] ind icator light ap ­
pears in the display. The need le in the tachome­
ter also moves into the
READ Y position .
~ The engine starts again when you take your
foot off the brake pedal. The ind icator light
tu rns off.
Add ition al informa tion
The engine stops in the "P", "N" and "D" selector
lever positions .
If you select the "R" selector lever position during
a Stop phase, the engine will start again.
Shift to "P" quickly to prevent the engine from
starting unintentiona lly when shifting t hrough
IIRII.
You can determ ine for you rself if the engine will
stop or not by reducing or increasing the amount
of force you use to press the brake pedal. For ex­
ample, if you only light ly press on the brake ped­
al in stop-and-go traff ic or when turning, the en­
g ine will not switch off when the vehicle is sta­
tionary . As soon as you press the brake down
harder, the eng ine will switch off .
(D Tips
-Press the brake pedal during a Stop phase
to keep the veh icle from roll ing.
- The ignition will turn off if you press the
I STAR T ENGINE ST OP ! button* during a
stop phase . The needle in the tachometer
moves into the
OFF pos it ion .
General information
App lies to: ve hicles w ith Sta rt/Stop system
Engine does not switch off
Before and during each stop phase, the system
checks if certa in cond itions have been met. If the
fjj i ndicato r light appears in the instr ument clus­
t er d isp lay, the engine w ill no t be s topped, for
examp le in the fo llowing situations:
1) Ma rket -spe cific
80
- T he engine has not reached the minim um re­
quired temperature for Start/Stop mode.
- The interior temperature selected by the cli-
mate control system* has not been reached.
- The ou tside tempe rat ure is extremely high/low.
- The windsh ield is being
defrosted® .
-The parking system* is switched on .
- The vehicle battery charge level is too low .
- The steering wheel is turned at a sharp angle or
is moving.
- After engaging the reverse gear.
- On sharp inclines .
- At high altitudes .
Engine automaticall y restarts
The standard Start/Stop mode w ill be canceled
d u ring a stop p hase in the following situat ions.
The eng ine res tarts witho ut any act ion by the
drive r.
- The vehicle ro lls, for example while on a slope .
- The interior temperature differs from the tem -
peratu re selected in the A/C system .
- The windsh ield is being
defrosted® .
-The brake pedal is pressed several times in a
row.
- The vehicle battery charge level is too low.
- Power consumption is hig h.
The eng ine ca n tur n off aga in when the cond i­
t ions for Sta rt/S top mode a re met
l ).
Ignition is switched off automaticall y
To prevent the vehicle battery from dra ining, the
i gnition will sw itch off
a ut omaticall y under the
fo llow ing cond it ions:
- The Start/Stop system has stopped the engine .
- The vehicle is stationary.
- You exited the vehicle .
In this case, the activated low beam is rep laced
by the pa rking light . The parking lights wi ll
switch off after approximately 30 minutes or
when you lock the veh icle.
.,.

Drivin g
~ To start driving and re lease the parking brake
automatica lly, press the acce lerator pedal as
usua l.
I n addition to re leasing the par king brake auto ­
matica lly, other convenience and sa fety functions
are available when you start driving
r=;, poge 83,
Starting from a stop.
Pre venting th e automatic parking bra ke
r el eas e
The vehicle could begin ro lling unintentiona lly,
dep ending on the hill or if towing a trailer .
~ To preve nt the parking b rake from releasing au­
tomatica lly, pull and hold the
®l switch and
press the acce lerator pedal. The parking brake
remains set and pr events the vehicle from ro ll­
ing backward.
~ You can re lease the(®) switch again once you
are sure that you are g iv ing enough dr iv ing
force to the wheels by pressing the accelerator pedal.
Emergenc y bra king function
You can use the emergency brak ing funct ion in an
emergency situation, or if the standard brake op­
eration malfunctions or is disabled .
~ Pull and hold the(®) switch.
~ As soon as you release the (®) switch or acceler-
ate, the brak ing stops .
Pu lling and holding
the(®) switch while driving
the vehicle activates the emergency braking f unc ­
tion . The vehicle is braked at all four wheels by
activating the hydraulic brake system. The brak­
ing effect is s imilar to heavy braking
r=;, .,&. .
To reduce the risk of activating the emergency
braking by mistake, a warn ing tone (bu zzer)
sounds when the
®l swi tch is pulled. Emergency
braking stops as soon as the
®l switch is released
or the accelerato r pedal is pressed .
Parking
~ Press the brake peda l to stop the vehicle.
~ Pull the C® switch to set the parking brake.
~ Place the selector lever in the P pos ition.
~ T urn the eng ine off r=;, .,&. .
82
~ Turn the steering w hee l when parking on in­
clines so that the w heels wi ll roll into the curb
if the vehicle starts moving .
A WARNING
- Do not press the acce lerator pedal inadver­
tently if a gear is selected when the vehicle
is stationary and the eng ine is running . Oth­
erwise, the vehicle will start to move imme­
d iate ly and this could resul t in an accident.
- Emerge ncy brak ing should only be used in
a n emergency, when the norma l bra ke pedal
has fa iled or the bra ke peda l is obstr ucted.
D ur ing eme rgency bra king, you r vehicle w ill
brake s imilar to he avy braking. ESC and the
associated components (ABS, AS R, EDL)
cannot overcome the laws of physics.
Around curves and when road or weather
conditions a re bad, a full brake applicat ion
can cause the veh icle to skid or the rear end
to swerve, wh ich increases the risk of an ac­
cide nt.
- If the power supply fails, you cannot set the
parking brake if it is released. In this case,
pa rk the veh icle on leve l ground and secure
it by p lac ing the sele cto r leve r in the P pos i­
tion. See an au thor ized A udi dealer or au ­
thor ized A udi Se rvi ce Fa cility for assis tan ce.
- I f you leave the vehi cle, sw itch the ignition
off and take the veh icle key wi th yo u. Thi s
app lies pa rticular ly when children remain in
the vehicle. Otherwise, chi ld ren co uld start
the engine, release the parking brake or op ­
erate e lectr ica l equipment s uch as power
w indows, wh ich increases the r isk of an acci­
dent.
- No one, especially c hildren, should rema in
in the vehicle when it is locked. Locked
doors make it more difficu lt for emergency
workers to get into the vehicle, which puts
lives at ris k.
(D Tips
When stopp ing at a traff ic signa l or stopp ing
i n city traffic, you can set the park ing brake
manually . The veh icle does not have to be
h eld with the brake pedal. The par king b rake
e liminates t he tendency to creep when a

selector lever position is engaged. As soon as
you press the accelerator pedal, the parking brake releases automatically and your vehicle
starts to move
¢ page 83.
(D Tips
- Occasional noises when the parking brake is
set and re leased are normal and are not a
cause for concern.
- The parking brake goes through a self-test
cycle at regular intervals when the vehicle is
stopped. Any noises associated with this are normal.
- If there is a power failure, the parking brake will not set if it is released, and it will not
release if it is
set¢&. See an authorized
Audi dealer or authorized Audi Service Fa­
cility for assistance .
Starting from a stop
Various convenience and safety functions may be
available when the vehicle begins driving, de­
pending on vehicle equipment.
Starting on hills with the parking brake set
Requirement: the driver's door must be closed.
~ To start driving comfortably when on a hill, set
the parking brake and begin driving as usual.
The braking force of the parking brake does not release automatically until the wheels build up
enough driving force .
Starting on hills with hill hold assist
Hill hold assist makes it easier to start on hills.
Requirement: the driver's door must be closed
and the engine must be running.
~ To activate hill hold assist, press and hold the
brake pedal for several seconds. The vehicle
must be in an uphill direction of travel.
After releasing the brake pedal, the braking pow­
er is maintained for a brief
moment ¢.&. to pre­
vent the vehicle from rolling back when starting.
::li During this time, you can eas ily beg in to move .-<
~ your vehicle.
N .-< 0 N > 00
Driving
A WARNING ,-
Applies to: ve hicles with h ill ho ld assist
- If you do not begin driving immediately or
the engine stalls after releasing the brake
pedal, your veh icle may begin to roll back ­
ward. Press the brake pedal or set the park­
ing brake immediately.
- The intelligent technology of hill hold assist
cannot overcome the limitations imposed by
natural physical laws. The increased comfort
offered by hill hold assist should not cause
you to take safety risks.
- Hill hold assist cannot hold the vehicle in
place on all hills (for example, if the ground
is slippery or icy).
- To reduce the risk of an accident, always
make sure the vehicle is situated safely
while stationary.
Automatic transmission
Introduction
Applies to: vehicles with automatic transmiss ions
T he automatic transmission is controlled elec­
tronically . Upshifting and downshifting occur au­
tomatically.
When a
moderate driving style is used, the
transm ission selects the most economica l dr iv ing
mode. The transmission upshifts at a lower RPM
and downshifts at a higher RPM to improve fuel
efficiency.
In the "S" selector lever position, the transm is­
sion switches to a sporty mode after a kick-down
or when the driver uses a
sporty driving style
characterized by quick accelerator pedal move­
ments, heavy acce leration, frequent changes in
speed and traveling at the maximum speed.
If desired, the driver can also select the gears
manually (tiptronic mode) ¢ page 88, Manual
shifting (tiptronic mode).
The S tronic is a dual-clutch transmission. Power
is transferred using two clutches that work inde­
pendently from one another. They replace the
torque converter used in conventional automatic
.,.
83

u. 00 .-< N l'­ N .-< 0 N > 00
-Power is still transferred to the wheels
when the engine is running at idle. To pre­
vent the vehicle from "creeping", you must keep your foot on the brake when the en­
gine is running and the selector lever is in
the "D", "S" or "R" position or "tiptronic"
mode is selected.
- Do not inadvertently press the accelerator
peda l when the vehicle is stopped if a gear is
engaged. Otherwise the risk of an accident
increases because the vehicle will start to
move immediately, even if the parking brake
is set.
- To reduce the risk of an accident, do not
press the acce lerator pedal when changing
the selector lever position while the vehicle is stationary and the engine is running.
- Never engage the "R" or "P" selector leve l
positions while driving. It could cause a
crash.
- Before driving down a steep slope, reduce
your speed and shift into a lower gear with
"ti ptron i c".
- Do not ride the brakes or press the brake
pedal too often or too long when driving
downhill. Constant braking causes the
brakes to overheat and substantially re­
duces braking performance, increases brak­
ing distance or causes complete failure of
the brake system.
- If you must stop on an incline, always hold
the vehicle in p lace with the foot brake or
park ing brake to prevent it from rolling
back.
- Never hold the veh icle on an incline with a
sl ip ping clutch. The clutch opens automati­
cally when it becomes too hot from the
overload. The
ml indicator light turns on
and a message appears
¢ page 89 when
the clutch is over loaded .
{LlJ) Note
- When stopping on an incline, do not try to
ho ld the vehicle in place by pressing the ac­
ce lerator pedal while a driving gear is se ­
l ected. This can cause the automatic trans ­
mission to overheat and can damage it. Set
Driving
the parking brake or press the brake pedal
to prevent the vehicle from rolling.
- Allowing the vehicle to roll when the engine
is stopped while the selector lever is in the
"N" position will damage the automatic
transmission, because it is not lubricated
under those circumstances
¢ page 3 78,
Towing with a tow truck.
- The transmission can overheat and be dam­
aged under certain driving and traffic condi­
tions such as frequent starts, creeping for a
long time, or stop-and-go traffic. When the
ml or. indicator light turns on, stop the
vehicle at the next opportunity and let the
transmission cool¢
page 89.
(D Tips
For safety reasons, the park ing brake only re­
l eases automatically when the driver's door is
closed.
Hill descent control
App lies to : vehicles wi th automatic transmiss ions
The hill descent control system assists the driver
when driving down hills.
Hill descent control is act ivated when the selec­
tor lever is in the "D" or "S" posit ion and you
press the b rake pedal. The transmission auto ­
matically se lects a gear that is suitab le for the
hill. Hill descent contro l tries to ma inta in the
speed achieved at the time of braking, within
physical and technica l limitations. If may still be
necessary to adjust the speed with the brakes.
Because hill descent control cannot shift down
farther than 3rd gear, it may be necessary to
shift into tiptronic mode in very steep areas . In
th is case, shift into 2nd or 1st gear in t iptronic
mode to use the engine's braking force to rel ieve
the brakes.
Hill descent control switches
off once the hill lev­
els out or you press the accelerator pedal.
On vehicles with a cruise control system*
¢ page 120, hill descent control is also activated
when the speed is set .
.,,.
87

Driving
& WARNING
Hill descent control cannot overcome phys ical
limitations, so it may not be able to maintain
a constant speed under all condit ions. Always
be ready to apply the brakes .
Manual shifting (tiptronic mode)
Applies to: vehicles with automatic transmissions
The tiptronic mode allows the driver to shift the
gears manually.
F ig. 9 3 Center conso le : shifting manually w ith the se lector
l ever
F ig . 94 Steering wheel: shifting manual ly w it h the s hift
paddles*
Shifting with the selector lever
You can sh ift into tiptro nic mode while stationary
a nd while driv ing.
• To s hift into tiptronic mode, p ush the selector
lever from the "D/S" position to the right in the
t ip tr onic sh ift gate . Once the transmission has
swi tched modes, t he se lec tor lever posi tion
M
is shown in the instrumen t clus ter display
¢ page 84, fig. 90. For example, M4 means the
fo urth gear is engaged.
• To shift up a gear, tap the se lector lever for­
ward
0 ¢ fig. 93 .
88
• To shift down a gear, tap the selecto r lever
backward
0 -
Shifting with the shift paddles*
You can operate the s hift paddles in the "D/S" or
" M " (tiptro nic shift ga te) se lec tor lever posi tions.
• To shift up one gear, tap the shift paddle 0
¢fig . 94.
• To shift down a gear, tap the 0 shift paddle.
• Applies to: RS models: to select the lowest/
highest possi ble gear, press and hold the sh if t
paddle
0 10 .
If the shift paddles a re tapped wh ile in the "D/S"
selector lever position, a utomat ic mode sw itches
off briefly . To swit ch from manually shift ing bac k
to automatic shifting immediate ly, tap t he shift
padd le
0 ¢ fig . 94 for 1 second .
To keep sh ift ing using the shift padd les, move
the selec to r l ever to the right o ut o f th e "D/S" po­
sition into the tiptronic shift gate .
The tra nsmission a utomatically sh ifts up or dow n
before cr itical engine speed is reac hed.
Applies to: RS models: when accelerating, the
transm iss ion does
not au tomatically shift to the
next gear short ly before the maxim um permitted
engine RP M is re ached. Shift to the next highest
gear at the right time.
The tra nsmission on ly allows manual shifting
whe n the engine speed is w ith in the perm itted
r a nge.
Kick-down
Applies to: vehicles with automatic transmissions
Kick-down enables maximum acceleration.
When you p ress the accelerator pedal down be­
yo nd the res istance point (called kick-down), the
automat ic transmission downshifts into a lower
gear, depending on vehicle s peed and engine
RPM .
It shifts up into the next higher gear once
t h e maximum specified engine RPM is reached .
Applies to: RS models: in tipt ronic mode, the
transm iss ion does
not automa tic ally shift down
i nto a lower ge ar. If yo u m ust accelera te, for ex ­
ample to pass a vehi cle, you mus t sh ift manually .
..,.

u. co ... N l'­ N
A WARNING
Please note that the wheels could spin on
slick or slippery roads when kick-down is ac­
tive .
Launch control program
App lies to: ve hicles with S tro nic tra nsm issio n an d La unch
Co ntrol P rogram
-
The launch control program provides the best
possible acceleration when starting from a stop .
Requirement: the eng ine must be at operating
temperature and t he steer ing whee l must not be
turned.
.,. Deact ivate l) the S tart/Stop system*
~ page 81. The L ED in the ~ button turns on .
.,. Wi th the engine runn ing, p ress the I.!, O FF ! but­
ton briefly one time . The
11 indicator light
turns on and the message
Stabili zation control
( ESC ): s port. W arning! Rest ricted st a bilit y
ap­
pears in the instrument cluster display.
.,. Pull the selector lever back out of the "D/S" po­
s it ion br iefly to select the S pos it ion, or press it
toward the right into the t iptronic pos ition or
select the
Dynamic d riving mode in d rive se­
lect* ~ page 140.
.,. Press t he b rake peda l firmly with you r left foot
and hold it all the way down for at least one
second .
.,. At the same time, press the gas pedal a ll the
way down with your right foot unt il the engine
reaches and stays at a high RPM level.
.,. Remove your left foot from the brake pedal
within five
seconds ~,&. .
A WARNING
-Always adapt yo ur driv ing to the traffic flow.
- Only use Launch Control when road and traf-
fic cond itions allow it and other dr ivers will
not be endangered or impacted by you r driv­
ing and the vehicle 's accele ration.
- Please note tha t the drive whee ls can sp in
and the vehicle can break away when sport
8 l ) It is n ot poss ib le to deac tiv ate t he system wit h all ve rs io n s N &j of th e tran sm iss ion.
Driving
mode is switched on, especially when the
road is slippery.
- Once the vehicle has started moving, press
the !.!> OFF I button briefly to turn the sport
mode off.
(D Tips
- The transmission temperat ure may increase
significant ly after using the launch control
program. If that happens, the program may
not be ava ilable for a few minutes. It will be
availab le aga in after a cool-down period.
- When accelerating using the launch contro l
program, all vehicle parts are subject to
heavy loads . This can lead to increased
wear .
Transmission malfunction
Applies to: vehicles wit h automatic transmissions
• Transmis sion : malfunction! Pl eas e s top ve ­
hicle and shift to P
There is a malfunction in the transmission . Park
the vehicle securely and do not cont inue driv ing .
See an author ized Audi dealer or author ized Audi
Se rvice Facility for assistance .
• Transmission o verhe ating! Plea se stop th e
vehicle!
The transmission is too hot and can become dam­
aged. Stop and let the transmiss ion cool w ith the
engine running (at idle) i n the "P" selector lever
pos ition . T hen the ind icator light and the mes­
sage turn off, d rive to an authorized Aud i dealer
o r auth o rized Aud i Serv ice Facility immediately to
have t he malfunct ion cor rected . If the indicato r
light and the driver message do not turn off, do
not continue driving . See an authorized Audi
dealer or authorized Audi Service Facility for as­
s istance.
[O] Tran smission: malfunction! You can contin-
u e dri ving. See owne r's manual
.,.
89

u. 00 ... N l'­ N ... 0 N > 00
~ To loosen the s hifter boot, carefu lly insert the
flat side of the screwdriver sideways into the s li t near the shifter
boot ¢ fig. 95 .
~ Carefully pry the shifter boot out with the
screwdriver while gr ipping the boot at the fold
and pulling it upward and out -arrow -until all
four corners are released .
~ Fold the shifter boot up aro und the shifte r knob
¢ fig. 96.
Selector le ver eme rgenc y release
~ Press and hold the yellow re lease button with
the
screwdriver ¢ fig. 96 .
~ Press the release button in the selector lever @
and move the leve r into the "N" position .
~ Clip the shift cover back i nto t he shift gate after
us ing t he emergency release .
A WARNING
-Only activate the emergency re lease while
on a level s urface or a slight slope.
-Only move the se lec tor lever out of the "P"
position when the parking brake is set . If it
is not functioning, sec ure t he vehicle from
rolling using the brake peda l or other su ita­
ble means, such as block ing a front and a
rear wheel. An unsecured ve hicle may ro ll
away, wh ich increases the risk of an acc i­
dent .
-
Driving
91

e-tron
For additional information, see ¢ page 17, Trip
computer (Audi virtual cockpit).
~ Applies to: vehicles with analog instrument
cluster: Open the
Tachometer display by turn­
ing the left thumbwheel on the multifunction
steering wheel.
When opening the driver's door, the charge level is shown in the instrument cluster when the igni­
tion is switched on, or the charge level and the
remaining charge time for the high -voltage bat ­
tery is displayed when charging .
The power meter gives feedback about the partic­ ular accelerator pedal position and shows the
current demand
(%) for electricity or fuel regard­
less of which engine is active.
An economical driving and recuperation range is
shown in green
¢ page 99, Energy recovery (re­
cuperation) .
A driving range that is not economi­
cal is shown in orange .
(D Vehicle not drive ready (OFF)
@ Recuperation (CHARGE)
@ Vehicle ready to drive (READY) or
coasting
© Efficient driving with electric motor
and/or gasoline engine (EFFICIEN­
CY)
® Economic driving while the electric
motor or gasoline engine is in the
partial power range
@ Driving in full power range
0 100% output
@ BOOST: the electric motor supports
the combustion engine
® High-voltage battery charge level
@ EV mode: active a=,v, standby, a=,v
or currently unavailable. ~v
@ Speed limit for electric driving in EV
mode (80 mph/ 130 km/h)
Indicator lights and messages
Applies to: vehicles with plug -in hybr id drive
Also note the indicator lights in¢ page 20.
The gasoline engine is active when the II'§] indica­
tor light turns on.
96
•• Drive system: system fault! Safely park
vehicle
There is a malfunction in the plug-in hybrid sys­
tem. The brake booster and the power steering
may stop working. Stop the vehicle immediately
or as soon as possible. Park the vehicle in a safe place outdoors that is not near buildings, roof
overhangs, carports or similar structures. Switch
the ignition off. Have the problem corrected by
an authorized Audi dealer or authorized Audi
Service Facility.
•• Electric drive: overheated! Safely stop
vehicle and check coolant
The coolant level is too low or the coolant tem­
perature is too high.
Stop the vehicle in the outdoors as soon as it is
safely possible. Switch the ignition off.
Read the important safety
precautions ¢.& in
Coolant on page 103
and check the coolant level
¢page 102.
If the coolant level is OK, the malfunction may be
caused by the system overheating. Let the vehi­
cle's electric drive system cool down for some
time .
If the message turns off after cooling down and
switching the ignition back on, you can continue
driving. Contact an authorized Audi dealer or au­
thorized Audi Service Facility immediately to have
the malfunction corrected.
If the indicator light stays on, contact an author­
ized Audi dealer or authorized Audi Service Facili­
ty.
lltll Drive system: system fault! Please con­
tact workshop
There is a malfunction in the plug-in hybrid sys­
tem . Drive to an authorized Audi dealer or au­
thorized Audi Service Facility immediately to have
the malfunction corrected.
1/1111 Drive system: system fault! Restart not
possible. Please contact workshop
There is a malfunction in the plug-in hybrid sys­
tem. Do not open the hood. Drive to an author- ized Audi dealer or authorized Audi Service
.,,_