lock AUDI A4 1995 B5 / 1.G 01A Transmission Remove And Install Workshop Manual

34-27


Note
If 3282 transmission support is not available, transmission can be
removed and installed using VAG1383A transmission jack and
VAG1359/2 universal mount. - Roll VAG1383A transmission jack with 3282 transmission support
under transmission and support transmission.
- Support transmission using VAG1383A transmission jack.

- Align adjustment plate parallel to transmission and lock safety support
(arrow) on transmission.
Pa
ge 11 of 21 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM02.34.2

34-31

Transporting the transmission

Special tools and equipment

3282 transmission support
3336 transmission support jig
The transmission support jig can be used when
transporting the transmission and for setting up
3282 transmission support.

- Bolt 3336 transmission support jig to transmission housing.

- Adjust support jig on sliding piece using locking pin.
Number of holes visible (arrow): 17
- Lift transmission using workshop crane and 3336 transmission support
jig.
Pa
ge 15 of 21 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM02.34.2

34-32

Installing
Install in reverse order of removal, note the
following:

- Clean input shaft splines and (in case of used
clutch plates) hub splines. Remove corrosion
and apply only very thin coating of lubricant G
000 100 on splines. Do not grease guide sleeve.

- Check clutch release bearing for wear, replace if
necessary.

- Coat contact surface of clutch slave cylinder
pivot rod with thin layer of copper grease, e.g.
381 351 TE.

- Threaded holes for mounting clutch slave
cylinder to transmission and shift lever to shift
rod must be cleaned of locking compound
residue using thread tap before installation .

- Make sure dowel sleeves for aligning
engine/transmission are installed in cylinder
block, install if necessary.

- Always replace self locking nuts.
Pa
ge 16 of 21 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM02.34.2

34-33


- Lift up transmission until clutch slave cylinder with mounting bracket for
line/hose can be installed (arrow).
- Install intermediate plate (if applicable) between transmission and
engine onto appropriate engine dowel sleeves.
- Make sure intermediate plate is correctly positioned on engine.
- Install lower engine/transmission and starter mounting bolts, and install
starter Repair Manual, Electrical Equipment, Repair Group 27

- Before installing, use tap to clean threads in flange shaft for driveshaft
on transmission to remove traces of locking compound.
- Replace gaskets on drive axles and on front of driveshaft Page 39
-
69
.
- Install driveshaft Page 39
-71
.
- Check adjustment of shift rod and pivot rod, re-adjust if necessary
Page 34
-12
.
Pa
ge 17 of 21 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM02.34.2

34-34

- Align exhaust system free of stress.
Repair Manual, Engine Mechanical, Repair
Group 26
- Check transmission oil level Page 34
-38
.

- After
connecting
battery,
enter anti-
theft code
for radio
Repair Manual,
Electrical Equipment, Repair Group 91


- Run power windows fully up by pressing
switches.

- Operate all power window switches again and
hold for at least one second in "close" position to
activate automatic one-touch function.

- Set clock to correct time.
Pa
ge 18 of 21 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM02.34.2