manual transmission AUDI A4 1995 B5 / 1.G 01W Transmission Remove And Install Workshop Manual

34-19

Vehicles with 1.8T four-cylinder engine

- Disconnect wires/and harness connectors as follows:
1 - At solenoid valve for wastegate bypass regulator valve -N75-
2 - At Evaporative Emission (EVAP) canister purge regulator valve -N80-
3 - At power output stage -N122-
4 - At Mass Air Flow (MAF) sensor -G70-
- Disconnect hoses and remove air cleaner housing (arrows).
- Remove coolant expansion tank from bracket and lay to side.

Repair Manual, Engine Mechanical, Repair Group 26
Note:
Do not bend flex pipe on front exhaust pipe more than 10 . - Disconnect harness connector for Heated Oxygen Sensor (HO2S)
(arrow) and move wiring clear.
- Remove nuts securing turbocharger to front exhaust pipe.
Pa
ge 2 of 20 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.2

34-22


6-cylinder engine - Unbolt right transmission support together with bonded rubber mount
(arrows).
- Loosen clamping sleeves of exhaust system and slide toward Three
Way Catalytic Converter (TWC).
- Remove Three Way Catalytic Converter (TWC) together with exhaust
pipe from below.
- Remove heat shields above left and right drive axles.

Repair Manual, Engine Mechanical, Repair Group 26 - Unbolt front exhaust pipes together with Three Way Catalytic
Converters (TWCs) from left and right exhaust manifolds (3 nuts on
each side) (arrows).
Pa
ge 5 of 20 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.2

34-24


Note:
Starter cables do not have to be disconnected. - Remove starter from engine/transmission and secure if necessary
Repair Manual, Electrical Equipment, Repair Group 27
.

- Disconnect shift rod (arrow -A-).
- Remove socket-head bolt from pivot rod (arrow -B-).
Pa
ge 7 of 20 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.2

34-25

All models

- Remove bottom engine/transmission mounting bolts, except for bolts
indicated by arrows -A- and -B-.

Notes: - Set up 3282 transmission support for removing manual transmission
01A (all wheel drive) using 3282/10 adjustment plate and place on
VAG1383A transmission jack.
A - Attachments
Attachments -A- are shown in schematic form.Arrow -B- points in the direction of travel.3282/10 adjustment plate only fits in one position.
Pa
ge 8 of 20 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.2

34-32


Repair Manual, Electrical Equipment, Repair Group 27

Repair Manual, Engine Mechanical, Repair Group 26
Radio Operating Manual - Lift transmission until clutch slave cylinder with mounting bracket for
line/hose can be installed (arrow).
- Install lower engine/transmission and starter mounting bolts and install
starter.
- Check adjustment of shift mechanism and adjust if necessary Page
34
-12
.
- Align exhaust system free of stress.- Check transmission oil level Page 34
-36
.
- After connecting battery, enter anti-theft code for radio.- Fully close power windows to stop.
- Then activate all power window switches ("up") for at least a second to
activate automatic window raising/lowering.
- Set clock to correct time.
Pa
ge 16 of 20 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.2