automatic transmission AUDI A4 1995 B5 / 1.G APB Engine Cylinder Block Crankshaft And Flywheel Assembly Manual

13-26

Vehicles with automatic transmission

- Remove transmission.

Repair Manual, 5 Spd. Automatic
Transmission 01V, Repair Group 37


- Drain off coolant Page 19
-19
.

Note:
Turn over the engine at the central bolt on the crankshaft.
CAUTION!
Injury risk - do not turn engine while feeling for TDC drilling. - Turn crankshaft to TDC by hand. Marks -A- and -B- must be aligned.
- Check position of camshafts: larger holes in securing plates on
camshaft sprockets must align opposite one another on inside. If this is
not the case, turn crankshaft one revolution further.
- Remove sealing plug from cylinder block, left.
- The TDC drilling in crankshaft must be visible (or able to be felt) in line
with sealing plug hole.
Pa
ge 13 of 26 C
ylinder block, crankshaft and fl
ywheel, disassembl
y and assembl
y
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.13.2

13-27


Installing - Screw clamping bolt 3242 for crankshaft into sealing plug hole and
tighten.
- Mark positions of holes in drive plate, shim -1- and washer -2- in
relation to crankshaft.
- Mark positions of shim -1- in front of drive plate and washer -2- behind
drive plate.

Note: - Install drive plate with washer -2- and shim -1- (3.0 mm or 4.0 mm).
Short engines and exchange engines are supplied without bush in
crankshaft. On vehicles with automatic transmission, always knock in
new bush before installing drive plate. Always replace drive plate securing bolts.
Pa
ge 14 of 26 C
ylinder block, crankshaft and fl
ywheel, disassembl
y and assembl
y
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.13.2

13-28

Tightening torques

Drive plate to crankshaft
60 Nm + 90

Note:
Always replace securing bolts for drive plate.

Note:
Before installing the transmission, check that the dowel sleeves for
locating engine/transmission are fitted in the engine flange.
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 37
- Measure distance -a- at three points and calculate average value.

Distance -a- = approx. 29.9 mm.
- Install a different shim if necessary.
- Install transmission.
Pa
ge 15 of 26 C
ylinder block, crankshaft and fl
ywheel, disassembl
y and assembl
y
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.13.2

13-31

Tightening torques

Dual-mass flywheel to
crankshaft 60 Nm + 180
Clutch to dual-mass flywheel 20 Nm

B - Drive plate

Removing

- Remove transmission.

Repair Manual, 5 Spd. Automatic
Transmission 01V, Repair Group 37


Note:
Turn over the engine at the central bolt on the crankshaft. - Turn crankshaft to TDC by hand. Marks -A- and -B- must be aligned.
- Check position of camshafts: larger holes in securing plates on
camshaft sprockets must align opposite one another on inside. If this is
not the case, turn crankshaft one revolution further.
- Remove sealing plug from cylinder block, left.
Pa
ge 18 of 26 C
ylinder block, crankshaft and fl
ywheel, disassembl
y and assembl
y
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.13.2

13-33

Installing

Note: - Install drive plate with washer -2- and shim -1- (3.0 mm or 4.0 mm).
Short engines and exchange engines are supplied without bush in
crankshaft. On vehicles with automatic transmission, always knock in
new bush before installing drive plate. Always replace drive plate securing bolts.
Tightening torques

Drive plate to crankshaft
60 Nm + 90
Pa
ge 20 of 26 C
ylinder block, crankshaft and fl
ywheel, disassembl
y and assembl
y
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.13.2

13-34


Note:
Before installing the transmission, check that the dowel sleeves for
locating engine/transmission are fitted in the engine flange.
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 37
- Measure distance -a- at three points and calculate average value.

Distance -a- = approx. 12.3 mm.
- Install a different shim if necessary.
- Install transmission.
Pa
ge 21 of 26 C
ylinder block, crankshaft and fl
ywheel, disassembl
y and assembl
y
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.13.2