display AUDI A4 1995 B5 / 1.G APB Engine Motronic Syst

01-90

- Press buttons -0- and -4- to select function
"Basic Setting" System in Basic Settin
g
04 - Basic Settin
g

Indicated on display
- Confirm entry by pressing -Q- button.
System in Basic Setting Input displa
y group number XXX

Indicated on display
Note:
Display Group 000 is used here as an example to illustrate the procedure.
(000 is to select Display Group 000)
Note:
When the display group is selected the EVAP valve is closed and the air
conditioner compressor is switched off. - Select required display group number from the Display Group
Overview in "Read Measuring Value Block" section.
- Press buttons -0- three times.
System in Basic Settin
g
Q
Input display group number
000

Indicated on display
- Confirm entry by pressing -Q- button.
System in basic setting 0

Indicated on display
Pa
ge 109 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1

01-91

Display group 000 (indicated values decimal)

Engine running at idle (Coolant Temperature not less than 80 C)
1 2
3 4
5 6
7 8
9 10
Display fields
Specification Represents





Adaptation value of mixture formation, bank 2 108 - 148 -4 to 4%





Adaptation value of mixture formation, bank 1
108 - 148
-4 to 4%




Control value of mixture formation bank 2
(If out of specification perform road test) 122 - 136 -4 to 4%




Control value of mixture formation bank 2
(If out of specification perform road test)
122 - 136
-4 to 4%



Adaptation value torque loss at idle 124 - 140 -3 to 5%



Idle torque
126 - 135
-1.5 to 1.5%


Throttle valve angle 1 - 7 0.4 to 2.75%


Engine speed (idle speed)
77 - 83
770 - 830 RPM

Engine load (without consumers) 21 - 34 15 - 26%
Engine Coolant Temperature (requirement for basic setting)
177 - 203
85 - 105 C
1) Up-to-date specifications:
Pa
ge 111 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1

01-92

- Allow engine to idle for a few minutes: Coolant
temperature at least 80 C.
Notes:

When the PRINT button is pressed the current
display will be printed out.
Press C button before selecting further display
groups.

- If readouts in all display fields match
specifications, press button.
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -6- to select function "End Output".
Rapid data transfer
HELP
06 - End Output

Indicated on display
- Confirm with -Q- button.
Rapid data transfer
HELP
Select function XX

Indicated on display
Pa
ge 112 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1

01-93

Control module, coding


Notes:

If the correct coding for the vehicle is not
displayed, or if the control module has been
replaced, the control module must be coded.

- Connect vehicle diagnostic, testing and
information system VAS 5051 or VAG1551 scan
tool and select engine electronics control
module by entering address word "01" Page 01
-9 . When doing this the ignition must be
switched on.
8D0907551.. 2.7L V6/5VT
G 0002
Codin
g 06711
WSC 06388

The display of VAG1551 will show the control module coding (example).
The relevant vehicle coding must be displayed, note coding table Page 01
-94
.
Pa
ge 113 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1

01-96
If an incorrect coding is displayed:

-
Press button.Rapid data transfer
HELP
Select function XX

When indicated on display
- Press buttons "07" for the function "Code Control Module" and press Q
button to confirm input.
Code Control Module
Q
Input code number XXXXX
(0-32000
)

When indicated on display
- Input control module coding according to coding table and press -Q-
button to confirm input Page 01
-94
.
Function unknown or
.
cannot be carried out currentl
y

If this message appears:
Check in parts catalog if the correct control module has been installed
(part number). It also possible that an incorrect code number was entered.
If necessary repeat coding.
-
Press button.
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -6- to select function "End Output" and confirm
entry with -Q- button.
Pa
ge 117 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1

01-97

Read Measuring Value Block


Test requirements

Coolant temperature at least 80 C

Electrical consumers switched off (radiator
fan must not run during the check)
A/C switched off

- Connect vehicle diagnostic, testing and
information system VAS 5051 or VAG1551 scan
tool and select engine electronics control
module by entering address word "01" Page 01
-9 . When doing this the engine must be
idling.
Rapid data transfer
HELP
Select function XX

Indicated on display:
- Press buttons -0- and -8- to select function "Read Measuring Value
Block" and confirm entry with -Q- button.
Read Measuring Value Block Input displa
y group number XXX

Indicated on display
Pa
ge 118 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1

01-98

- Input relevant Display Group number (3 figures)
and confirm entry by pressing -Q- button.

Note:
The display group number required is indicated
in the instructions for testing functions and
components given in the relevant sections of this
Manual. Read Measuring Value Block 0 1
2
3
4
5
6
7
8
9
10

Indicated on display for display group 000:
Note:
To change to another display group proceed as follows: Display group
VAG1551 scan tool
VAS5051
tester
Higher Press button 3
Press button
Lower Press button 1
Press button
Pa
ge 119 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1

01-99

Readiness code

The readiness code is a 8 digit display in
measuring value block 086, display field 1. Each
of the 8 digits is assigned to a specific exhaust
related system.
If the function of these systems is checked via a
test by On Board Diagnostic (OBD), which is
successfully completed, then the position
assigned to this system will be switched from "1"
to "2." This occurs regardless of whether the test
is indicated as "OK" or "not OK" as long as the
test is successfully completed.
If a test is completed, but indicated as "not OK",
a DTC will be stored in the DTC memory. Check
DTC memory Page 01
-15
.
When the readiness code is generated after a
successfully completed test, "00000000" will be
displayed. (Measuring value block 086, display
field 1).
Pa
ge 120 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1

01-101

Readiness code, checking


Test sequence

- Connect vehicle diagnostic, testing and
information system VAS5051 or VAG1551 scan
tool to vehicle and select Control module for
engine electronics "Address Word" 01 Page
01
-9 . The ignition must be switched on.
Rapid data transfer
HELP
Select function XX

When indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block" and
press -Q- button to confirm input.
Read Measurin
g Value Block
Q
Input displa
y group number XXX

When indicated on display
- Press buttons "086" for "display group number 086" and press -Q-
button to confirm input.
Read Measuring Value Block 86
1
2
3
4

When indicated on display
- Check readiness code in display field 1

Specified value: 0 0 0 0 0 0 0 0
Pa
ge 122 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1

01-102


Display fields

1 2 3 4
Display Group 086: Readiness code
Display
0 0 0 0 0 0 0 0 X X X X X X X X X X X X X X X X
X X X X X X X X
Indicated
Ready-bits
completed tests Cycle-Flags
Performed cycles Cycle-Flags
Performed cycles Cycle-Flags
Performed cycles
Work area
1 = not completed
0 = completed 1 = not completed
0 = completed 1 = not completed
0 = completed 1 = not completed
0 = completed
Specified value
0 0 0 0 0 0 0 0 X X X X X X X X X X X X X X X X X X X X X X X X
Note:
Readiness code significance on next pages Note for display field 1:
This display field indicates which diagnosis was checked last after the DTC memory was erased or if the control module was
replaced. After erasing the DTC memory, all values that can be checked will be reset to 1, after successful testing these
values will be reset to 0.
Pa
ge 123 of 166 Motronic s
ystem, On Board Dia
gnostic
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1