display AUDI A4 1996 B5 / 1.G AFC Engine On Board Diagnostic Multiport Fuel Injection Repair Manual

01-88

Output on GST and/or on
VAG 1551 scan tool Possible malfunction cause

Malfunction repair
P0706 / 17090
Transmission Range Sensor
Circuit Range/Performance Engine control module incorrectly coded

- Cause: the vehicle is equipped with
manual transmission, but was coded
for vehicle with automatic
transmission.
- Remedy: code vehicle correctly
according to Coding Table

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
MIL Status:
Malfunction not displayed by
MIL Automatic transmission: faulty wiring
connection between Engine Control Module
(ECM) -J192- and multi-function Transmission
Range (TR) switch -F125-

- Check gear recognition signal
page 24
-99

For troubleshooting
Display group 004
Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again

Automatic transmission: malfunction of
multi-function Transmission Range (TR) switch
-F125-

Repair Manual, 5 Spd. Automatic
Transmission 01V On Board Diagnostic (OBD), Repair Group 01
- Check multi-function Transmission
Range (TR) switch -F125-

Malfunction cause found: Yes

Pa
ge 118 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-89

Output on GST and/or
on VAG 1551 scan
tool Possible malfunction cause

Malfunction repair
P0707 / 17091
Transmission Range
Sensor Circuit Low
Input Wiring connection between Engine Control
Module (ECM) -J192- and multi-function
Transmission Range (TR) switch -F125- on
automatic transmission faulty

- Check gear recognition signal page 24
-99


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
MIL Status:
Malfunction not
displayed by MIL Malfunction on multi-function Transmission
Range (TR) switch -F125- of automatic
transmission

Repair Manual, 5 Spd. Automatic
Transmission 01V On Board Diagnostic (OBD), Repair Group 01, Electrical testing

- Check multi-function Transmission
Range (TR) switch -F125-
For troubleshooting
Display group 004
Malfunction cause found: Yes


- Erase DTC memory, test drive and
after test drive, check DTC memory
again
Pa
ge 120 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-90

Output on GST and/or
on VAG 1551 scan tool
Possible malfunction cause

Malfunction repair
P1101 / 17509
(B1-S1) Voltage too
Low/Air Leak Harness connector for Heated Oxygen
Sensor (HO2S) -G39- (B1-S1) loose or
corroded due to moisture in the harness
connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately
Leak in Bank 1 exhaust system before
Heated Oxygen Sensor (HO2S) -G39- (B1-
S1)

- Determine and repair leak

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again

Wiring connection to Heated Oxygen
Sensor (HO2S) -G39- (B1-S1) faulty, or
sensor -G39- faulty

- Check HO2S -G39- (B1-S1) page 24
-
49

For troubleshooting
Display group 010
Malfunction cause found: Yes
No
Continued next page

- Erase DTC memory, test drive and after
test drive, check DTC memory again
Pa
ge 121 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-92

Output on GST and/or
on VAG 1551 scan tool
Possible malfunction cause

Malfunction repair
P1102 / 17510
Heating Circ. (B1-S1)
Short to B+ Harness connector for Oxygen Sensor
(O2S) heater -Z19- (B1-S1) loose or
corroded due to moisture in the harness
connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately
Wiring connection of Oxygen Sensor
(O2S) heater -Z19- (B1-S1) faulty, or heater
-Z19- faulty

- Check O2S heater -Z19- (B1-S1) page 24
-51


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
For troubleshooting
Display group 040
Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
erase DTC memory and
test drive check DTC memory
Notes:

|The heating of the oxygen sensor probes in front of Three Way Catalytic Converter (TWC) is switched on with the fuel
pump relay, i.e. immediately at engine start.
Pa
ge 123 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-93

Output on GST and/or
on VAG 1551 scan
tool Possible malfunction cause

Malfunction repair
P1104 / 17512
(B1-S2) Voltage too
Low/Air Leak Harness connector for Oxygen Sensor (O2S)
behind Three Way Catalytic Converter (TWC) -
G130- (B1-S2) loose or corroded due to moisture
in the harness connector

- Check harness connector for tight fit
and contact corrosion, if necessary
reconnect and/or clean, installation
location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
MIL Status:
MIL lights up
immediately
Leak in bank 1 exhaust system between
Heated Oxygen Sensor (HO2S) -G39- and
Oxygen Sensor (O2S) behind Three Way
Catalytic Converter (TWC) -G130-

- Find and repair leak
For troubleshooting
Display group 041
Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
Pa
ge 125 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-95

Output on GST and/or
on VAG 1551 scan tool
Possible malfunction cause

Malfunction repair
P1105 / 17513
Heating Circ. (B1-S2)
Short to B+ Harness connector for Oxygen Sensor
(O2S) heater -Z29- (B1-S2) loose or
corroded due to moisture in the harness
connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately
Wiring connection of Oxygen Sensor
(O2S) heater -Z29- (B1-S2) faulty, or heater
-Z29- faulty

- Check O2S heater -Z29-(B1-S2) page 24
-55


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
For troubleshooting
Display group 040
Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
erase DTC memory and
test drive check DTC memory
Pa
ge 127 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-96
Notes:

The heating for Oxygen Sensor Probes behind Three Way Catalytic Converter (TWC) is not switched on immediately at
engine start, but when the calculated exhaust gas temperature drops below 308 C (586 F) ( Read measuring value
block, display group 42, channel 1). The malfunction "P1105 / 17513" is set as soon as the probe heater is switched on (the vehicle must be driven approx. 60
sec. under load) and the heating current is greater than 10 A for longer than 80 ms.
Pa
ge 128 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-97

Output on GST and/or
on VAG 1551 scan tool
Possible malfunction cause

Malfunction repair
P1106 / 17514
(B2-S1) Voltage too
Low/Air Leak Harness connector for Heated Oxygen
Sensor (HO2S) 2 -G108- (B2-S1) loose or
corroded due to moisture in the harness
connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately Leak in Bank 1 exhaust system up to
Heated Oxygen Sensor (HO2S) 2 -G108-
(B2-S1)

- Find and repair leak

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again

Wiring connection to r Heated Oxygen
Sensor (HO2S) 2 -G108- (B2-S1) or -G108-
(B2-S1) faulty

- Check Heated Oxygen Sensor (HO2S) 2 -
G108- (B2-S1) page 24
-49

For troubleshooting
Display group 010
Malfunction cause found: Yes
No
Continued next page

- Erase DTC memory, test drive and after
test drive, check DTC memory again
Pa
ge 129 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-99

Output on GST and/or
on VAG 1551 scan tool
Possible malfunction cause

Malfunction repair
P1107 / 17515
Heating Circ. (B2-S1)
Short to B+ Harness connector for Oxygen Sensor
(O2S) heater -Z28- (B2-S1) loose or
corroded due to moisture in the harness
connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately Wiring connection of Oxygen Sensor
(O2S) heater -Z28- (B2-S1) faulty, or heater
-Z28- faulty

- Check O2S heater -Z28- (B2-S1) page 24
-51


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
For troubleshooting
Display group 040
Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
erase DTC memory and
test drive check DTC memory
Notes:

The heating of the oxygen sensor probes in front of Three Way Catalytic Converter (TWC) is switched on with the fuel
pump relay, i.e. immediately at engine start.
Pa
ge 131 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-100

Output on GST and/or
on VAG 1551 scan
tool Possible malfunction cause

Malfunction repair
P1109 / 17517
(B2-S2) Voltage too
Low/Air Leak Harness connector for Heated Oxygen Sensor
(HO2S) -G131- (B2-S2) loose or corroded due to
moisture in the harness connector

- Check harness connector for tight fit
and contact corrosion, if necessary
reconnect and/or clean, installation
location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
MIL Status:
MIL lights up
immediately
Leak in bank 2 exhaust system between
Heated Oxygen Sensor (HO2S) 2 -G108- and
Oxygen Sensor (O2S) 2 behind Three Way
Catalytic Converter (TWC) -G131-

- Find and repair leak

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
For troubleshooting
Display group 041
Wiring connection to Oxygen Sensor (O2S) 2
behind Three Way Catalytic Converter (TWC) -
G131- (B2-S2) faulty, or sensor -G131- faulty

- Oxygen Sensor (O2S) 2 behind Three
Way Catalytic Converter (TWC) -G131-
(B2-S2) page 24
-53


Malfunction cause found: Yes

- Erase DTC memory, test drive and
after test drive, check DTC memory
Pa
ge 133 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1