wiring AUDI A4 1996 B5 / 1.G AHA Engine Multiport Fuel Injection And Ignition System Owner's Manual

24-57
If there is no voltage:

If there is still no voltage: - Connect multimeter between harness connector terminal 1 (to ECM)
and vehicle Ground, using VW1594 connector test kit.
Specified value: 11.0-14.5 volts
- Check wiring between terminal 1 and relay panel using appropriate
wiring diagram.
Pa
ge 72 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-59
If specified value is not attained:

- Connect VAG1598/22 test box to ECM harness
connector page 01
-67
.

If wiring is OK: - Check wiring for open circuit between ECM/test box and 4-pin O2S
harness connector (to ECM).

Connector terminal 2 to ECM/test box socket 28
Specified value: max. 1.5
- Replace ECM -J220- page 01
-68
- Carry out adaptation of throttle valve control module to ECM page
24
-150
.
- Check readiness code page 01
-70
. If Diagnostic Trouble Code
(DTC) memory has been erased, or ECM was disconnected, generate
new readiness code page 01
-73
.
Pa
ge 74 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-68

Mass Air Flow (MAF) sensor, checking


Required special tools and test equipment

VAG1551 or VAG1552 Scan Tool (ST) with
VAG1551/3 adapter cable
VAG1598/22 test box
Multimeter US1119 (Fluke 83 or equivalent)
VW1594 connector test kit
Wiring diagram

Test requirements
All electrical consumers switched off (coolant
fan must not run during test).
A/C must be switched off
Fuse for MAF sensor OK
Pa
ge 89 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-72
Evaluation of display group 2, display field 4 Display
group: 2


Display field:
4
Possible malfunction cause
Corrective action
less than 2.8
g/s
Large amount of false air between intake air duct and
Mass Air Flow (MAF) sensor - Check intake air system for leaks (false
air) page 24
-126

larger than 5.6
g/s
Shift lever in drive range (auto. transmission)
Engine affected by additional consumers- Move shift lever into P or N
- Eliminate load (A/C, power steering,
generator)

Open circuits in wire 1 or 2 between MAF sensor and
ECM - Check voltage supply page 24
-73


Open circuit in wire 3 between MAF sensor and relay
panel - Check wiring page 24
-73
Pa
ge 94 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-73

Checking voltage supply

If there is no voltage:
Checking wiring - Disconnect 3-pin harness connector from Mass Air Flow sensor (MAF).
- Connect multimeter US1119 (Fluke 83 or equivalent) between harness
connector terminals 2 (Ground) and 3 (B+), using adapter cables from
VW1594 connector test kit.
Specified value: 9.0-14.5 volts
- Switch ignition off.
- Check wiring using applicable wiring diagram.
- Switch ignition off.
- Connect VAG1598/22 test box to ECM harness connector page 01
-
67
.
- Check wiring for open circuits, between ECM/test box and 3-pin MAF
sensor harness connector.

Connector terminal 1 to ECM/test box socket 13
Connector terminal 2 to ECM/test box socket 12
Specified value: max. 1.5
Pa
ge 95 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-74

- Check wiring for short circuits between terminals
of 3-pin connector, and between connector and
ECM/test box.


Connector terminal 1 to ECM/test box
socket 12

Specified value:

- Switch multimeter to 20 VDC measuring
range.

- Check wiring at 3-pin connector for short circuit
to B+ (battery positive voltage), according to
applicable wiring diagram.


Connector terminal 1 to vehicle Ground

Connector terminal 2 to vehicle Ground

Specified value: 0 volts
If wiring is OK:

- Replace Mass Air Flow sensor (MAF) -G70-.

-
Check readiness code page 01
-70
. If
Pa
ge 96 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-75

Engine Coolant Temperature (ECT)
sensor, checking


Required special tools and test equipment

VAG1551 or VAG1552 Scan Tool (ST) with
VAG1551/3 adapter cable
VAG1598/22 test box
Multimeter US1119 (Fluke 83 or equivalent)
VW1594 connector test kit
Wiring diagram

Test requirements
Engine cold
Pa
ge 98 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-77

- Compare display with specified value for engine
coolant temperature sensor (display field 3):

Display fields

1 2 3 4
Display group 4: General engine data
Display xxx RPM xx.xxx V
xxx.x C
xxx.x C
Indicates Engine
speed
(in 40 RPM
steps) Battery Positive
Voltage (B+) Engine coolant temperature Intake air
temperature
Range 0 - 6800
RPM 0.000 - 16.500 V -46.5 to 141.0 -46.5 to 141.0
Specified
value 0 RPM 10.000 - 14.500 V approx. ambient temperature 1), 2) ---

--- --- If specified value is not attained page 24
-79
,
Evaluation of display group 4
---
1) After a long standing period (approx. 12 hours). 2) If indicated temperature deviates significantly from the ambient temperature, check ECT sensor wiring for resistance or
open circuits.
Pa
ge 100 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-79
Evaluation of display group 4 Display group: 4


Display field: 3
Possible malfunction cause
Corrective action
approx. -46.5 C
Open circuit or short circuit in wiring to B+ - Check wiring page 24
-79
approx. 141.0 C
Short circuit to Ground

Checking wiring

- Connect VAG1598/22 test box to ECM harness
connector page 01
-67
.

- Disconnect 4-pin connector from ECT sensor -
G62-.

- Check wiring resistance for open circuit between ECM/test box and 4-pin
ECT sensor connector.

Connector terminal 1 to ECM/test box socket 53
Connector terminal 3 to ECM/test box socket 67
Specified value: max. 1.5
Pa
ge 103 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-80


- Check wiring for short circuit between ECM/test box and 4-pin harness
connector according to wiring diagram.

Connector terminal 1 to vehicle Ground
Connector terminal 1 to ECM/test box socket 67
Connector terminal 1 to terminal 3
Connector terminal 3 to vehicle Ground
Specified value:
- Check wiring between ECM and 4-pin harness connector for short
circuit to battery B+.

Connector terminal 1 to vehicle Ground
Connector terminal 3 to vehicle Ground
Specified value: 0 volts
Pa
ge 104 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1