diagram AUDI A4 1996 B5 / 1.G ATQ Engine Additional Signals Testing User Guide

24-189

- Repair open circuit or short circuit if
necessary.

Electrical Wiring Diagrams, Troubleshooting &
Component Locations binder If no malfunctions are found in wire:

- Check DTC memory of control module for
airbag:

Repair Manual, Body
-On Board Diagnostic
(OBD), Repair Group 01; On Board Diagnostic (OBD) of airbag system BAE (basic trigger unit) with side airbag; DTC memory, checking

Pa
ge 32 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6

24-191

Test requirement:

Control module coding OK Page 01
-71
.

Test sequence

- Switch ignition off.

- Connect VAG1598/31 test box at wiring harness
to ECM, do not connect ECM Page 24
-17
.

- Check the following wire connection for open
circuit and short circuit to Ground (GND) and B+:

Test box
VAG1598/31
Socket
ABS control module (w/EDL)
-J104-
Terminal
74 Electrical Wiring Diagrams,
Troubleshooting & Component
Locations binder
If no malfunctions are found in wire:

- Replace ABS control module.
If the malfunction is indicated again after
Pa
ge 34 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6

24-196

Example 1:

From the DTCs stored in the memories, you have determined that control
module 1 is not communicating with control modules 2 and 3.
Electrical Wiring Diagrams, Troubleshooting & Component Locations
binder Control module
DTCs stored in DTC memories:
1
Missing signal from control module 2Missing signal from control module 3
2 Missing signal from control module 1
3 Missing signal from control module 1
- Switch ignition off.
- Disconnect the control modules connected across the bus wires and
check the bus wires for an open circuit. - Replace control module 1 if no malfunctions can be found in the bus
wires.
Pa
ge 41 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6

24-197

Example 2:

From the DTCs stored in the memories, you have determined that control
module 2 is not communicating with control modules 1 and 3.
Electrical Wiring Diagrams, Troubleshooting & Component Locations
binder Control module
DTCs stored in DTC memories:
1
Missing signal from control module 2
2 Missing signal from control module 1Missing signal from control module 3
3 Missing signal from control module 2
- Switch ignition off.
- Disconnect the control modules connected across the bus wires and
check the bus wires for an open circuit. - Replace control module 2 if no malfunctions can be found in the bus
wires.
Pa
ge 42 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6

24-198

Example 3:
Using the DTCs stored in the memories, you
have determined that none of the control
modules are sending or receiving signals.

Control
module
DTCs stored in DTC
memories:
1
Powertrain databus faulty
2 Powertrain databus faulty
3 Powertrain databus faulty

- Switch ignition off.

Electrical Wiring Diagrams, Troubleshooting & Component Locations
binder - Disconnect the control modules connected across the bus wires and
check bus wires for a short circuit to B+ and Ground (GND).
Pa
ge 43 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6