AUDI A4 1996 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide

Manufacturer: AUDI, Model Year: 1996, Model line: A4, Model: AUDI A4 1996 B5 / 1.G
Pages: 20, PDF Size: 0.39 MB
AUDI A4 1996 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide A4 1996 B5 / 1.G AUDI AUDI https://www.carmanualsonline.info/img/6/941/w960_941-0.png AUDI A4 1996 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide
Search: (fuse chart, heater, towing capacity, maintenance, winter tyres, fuel type)
Trending: timing belt, wheel bolt torque, wheel torque, wheel bolts, clutch, transmission
Jump to page (1-20):

Page 11 of 20

AUDI A4 1996 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-57 Removing Engine in vehicle Lock carrier must be in service position Page 13 -1 . - Remove toothed belt Page 13 -40 . CAUTION! The air conditioner

Page 12 of 20

AUDI A4 1996 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-58 - Remove toothed belt sprocket from crankshaft. To do this, counter hold sprocket with 3415. - Remove oil pan Page 17 -11 - Remove bolts -1 to 6-. - Pry sealing flange loose

Page 13 of 20

AUDI A4 1996 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-59 WARNING! Wear protective glasses. Installing Note: The sealing flange must be installed within 5 minutes after applying silicone sealant. - Remove remaining sealant from sealing

Page 14 of 20

AUDI A4 1996 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-60 Note: The bead of sealant must not be thicker than 3 mm, otherwise excess sealant will enter the oil pan and obstruct the strainer in the oil intake line. Note: Use guide sleeve T10

Page 15 of 20

AUDI A4 1996 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-61 - Install crankshaft oil seal Page 13 -54 . - Install toothed belt (adjust valve timing) Page 13 -44 . - Install bracket for A/C compressor -Item 5 -, Page 13 -1

Page 16 of 20

AUDI A4 1996 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-62 Dual mass flywheel/drive plate, removing and installing Dual-mass flywheel Special tools and equipment Removing Counter-hold tool 10-201 - Reverse positi

Page 17 of 20

AUDI A4 1996 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-63 Installing Installation is carried out in the reverse order or removal; note the following: - Replace bolts. Tightening torque Component Nm Dual-mas

Page 18 of 20

AUDI A4 1996 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-64 Drive plate Special tools and equipment Removing Counter hold VW 558 Hex bolt M8 x 45 and two M10 hex nutsCaliper gauge or depth measure - Secure counter hold tool

Page 19 of 20

AUDI A4 1996 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-65 Installing - Place drive plate in position with shim -2- and washer -1-. Lug -arrow- must face towards torque converter. - Insert at least 3 old securing bolts and tighten to 3

Page 20 of 20

AUDI A4 1996 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-66 If nominal value is exceeded: If specified value is attained: Tightening torque 1) 90 corresponds to a quarter turn - Remove drive plate again and fit without shim -2-. Retig
Page:   < prev 1-10 11-20
Search: (length, keyless entry, hood release, turn signal bulb, sat nav, open bonnet)
Trending: transmission, timing belt, wheel torque, clutch, wheel bolts, wheel bolt torque
Jump to page (1-20):