check engine light AUDI A4 1997 B5 / 1.G AFC Engine On Board Diagnostic Multiport Fuel Injection Service Manual

01-102

Output on GST and/or
on VAG 1551 scan tool
Possible malfunction cause

Malfunction repair
P1110 / 17518
Heating Circ. (B2-S2)
Short to B+ Harness connector for Oxygen Sensor
(O2S) heater -Z30- (B2-S2) loose or
corroded due to moisture in the harness
connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately
Wiring connection for Oxygen Sensor
(O2S) heater -Z30- (B2-S2) faulty, or heater
-Z30- faulty

- Check O2S heater -Z30- (B2-S2) page 24
-55


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
For troubleshooting
Display group 040
Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
erase DTC memory and
test drive check DTC memory
Notes:

The heating for Oxygen Sensor Probes behind Three Way Catalytic Converter (TWC) is not switched on immediately at
engine start, but when the calculated exhaust gas temperature drops below 308 C (586 F) ( Read measuring value
Pa
ge 136 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

fuel injectors faulty, or fuel injectors -N30-, -
N31- or -N32- faulty
29

MIL Status:
MIL lights up immediately Malfunction cause found: Yes
No

- Erase DTC memory, test drive
and after test drive, check DTC
memory again

Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control
module page 01
-265
erase
DTC memory and test drive
check DTC memory Pa
ge 139 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

injectors faulty, or fuel injectors -N33-, -N83- or
-N84- faulty
24
-29

MIL Status:
MIL lights up immediately Malfunction cause found: Yes
No

- Erase DTC memory, test drive
and after test drive, check DTC
memory again

Engine Control Module (ECM) -J192- faulty

- Replace and code engine
control module page 01
-265

erase DTC memory and test
drive check DTC memory
Pa
ge 142 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

Short to B+
_______________________
MIL Status:
MIL lights up immediately

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again

Engine Control Module (ECM) -
J192- faulty

- Replace and code engine control
module page 01
-265
erase DTC
memory and test drive check DTC
memory
Note:
If the malfunction "P1213 / 17621" and/or "P1214 / 17622" and/or "P1215 / 17623" is recognized by the engine control
module, the corresponding fuel injector is no longer triggered and the oxygen sensor control is blocked until ignition on.
Pa
ge 144 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-113

Output on GST and/or on
VAG 1551 scan tool Possible malfunction cause

Malfunction repair
P1339 / 17747
Crankshaft Pos./Engine Speed
Sensors Cross connected 3-pin connector from Crankshaft
Position (CKP) sensor -G4- and engine
speed (RPM) sensor -G28-

- Disconnect both 3-pin harness
connectors and connect correctly,
installation location page 28
-7
P0322 / 16706
Ignition/Distributor Engine
Speed Input Circuit
No Signal
MIL Status:
MIL lights up immediately Malfunction cause found: Yes

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
Notes:

The malfunction "P1339 / 17747" is set when -G4- and -G28- are transposed.
Pa
ge 154 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

No
drive, check DTC memory again

Wiring connection to ignition coil power
output stage -N122- faulty or power output
stage -N122- faulty

- Check Power output stage -N122- for
ignition coils page 28
-13


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after test
drive, check DTC memory again
MIL Status:
MIL lights up
immediately
Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
erase DTC memory and test
drive check DTC memory
Note:
The power output stage is not integrated in the Engine Control Module (ECM) -J192-, it is a separate component.
Pa
ge 158 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

No
test drive, check DTC memory again

Wiring connection to Power output stage -
N122- for ignition coils or -N122- faulty

- Check Power output stage -N122- for
ignition coils page 28
-13


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately
Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
check DTC memory and
test drive check DTC memory
Note:
The power output stage is not integrated in the Engine Control Module (ECM) -J192-, it is a separate component.
Pa
ge 164 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-122

Output on GST and/or on
VAG 1551 scan tool Possible malfunction
cause
Malfunction repair
P1396 / 17804
Engine Speed Sensor
Missing Tooth Starter ring gear
damaged (teeth broken off)


- Remove starter and carry out visual inspection of the
starter ring gear. If broken teeth are found, replace
starter ring gear
MIL Status:
MIL lights up immediately Malfunction cause found:
Yes


- Erase DTC memory, test drive and after test drive,
check DTC memory again
For troubleshooting
Display group 037

Note:
The malfunction "P1396 / 17804" is set when the engine speed sensor does not supply 270 engine speed pulses per engine
revolution.
Pa
ge 165 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-123

Output on GST
and/or on VAG 1551
scan tool Possible malfunction cause

Malfunction repair
P1400 / 17808
EGR Valve Circ.
Electrical Malfunction Harness connector for EGR vacuum
regulator solenoid valve -N18- loose or
corroded due to moisture in the harness
connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately Wiring connection to EGR vacuum
regulator solenoid valve -N18- faulty or valve
-N18- faulty

- EGR vacuum regulator solenoid valve -
N18- page 24
-67


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again

Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
erase DTC memory and
test drive check DTC memory
Note:
The malfunction "P1400 / 17808" is set after engine start at an engine speed less than 900 RPM, an engine load less than
25% and EGR valve duty cycle less than 20%, as soon as the control module output of the EGR valve is "low" for longer than
1.2 sec.
Pa
ge 166 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-124

Output on GST
and/or on VAG 1551
scan tool Possible malfunction cause

Malfunction repair
P1402 / 17810
EGR Valve Circ.
Short to B+ Harness connector for EGR vacuum
regulator solenoid valve -N18- loose or
corroded due to moisture in the harness
connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately Wiring connection to EGR vacuum
regulator solenoid valve -N18- faulty, or valve
-N18- faulty

- EGR vacuum regulator solenoid valve -
N18- page 24
-67


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again

Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
erase DTC memory, test
drive and check DTC memory
Notes:
The malfunction "P1402 / 17810" is set after engine start at an engine speed between 1000 RPM and 3500 RPM, an engine
load between 33% and 66% and an EGR valve duty cycle greater than 30%, as soon as the control module output of the EGR
valve is "high" for longer than 1.2 sec.
Pa
ge 167 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1