lights AUDI A4 1997 B5 / 1.G AFC Engine On Board Diagnostic Multiport Fuel Injection Repair Manual

Short to B+
_______________________
MIL Status:
MIL lights up immediately

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again

Engine Control Module (ECM) -
J192- faulty

- Replace and code engine control
module page 01
-265
erase DTC
memory and test drive check DTC
memory
Note:
If the malfunction "P1213 / 17621" and/or "P1214 / 17622" and/or "P1215 / 17623" is recognized by the engine control
module, the corresponding fuel injector is no longer triggered and the oxygen sensor control is blocked until ignition on.
Pa
ge 144 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-107

Output on GST and/or on VAG
1551 scan tool Possible malfunction cause

Malfunction repair
P1216 / 17624
Cyl.4-Fuel Injector Circ.
Short to B+
-----------------------
P1217 / 17625
Cyl.5-Fuel Injector Circ.
Short to B+
_______________________
P1218 / 17626
Cyl.6-Fuel Injector Circ.
Short to B+
_______________________
MIL Status:
MIL lights up immediately Wiring connection to Cylinder 4, 5,
or 6 fuel injectors faulty, or fuel
injectors -N33-, -N83- or -N84- faulty
Yes

- Check fuel injectors page 24
-29

Malfunction cause found: Yes

- Erase DTC memory, test drive and
Pa
ge 145 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-113

Output on GST and/or on
VAG 1551 scan tool Possible malfunction cause

Malfunction repair
P1339 / 17747
Crankshaft Pos./Engine Speed
Sensors Cross connected 3-pin connector from Crankshaft
Position (CKP) sensor -G4- and engine
speed (RPM) sensor -G28-

- Disconnect both 3-pin harness
connectors and connect correctly,
installation location page 28
-7
P0322 / 16706
Ignition/Distributor Engine
Speed Input Circuit
No Signal
MIL Status:
MIL lights up immediately Malfunction cause found: Yes

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
Notes:

The malfunction "P1339 / 17747" is set when -G4- and -G28- are transposed.
Pa
ge 154 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-114

Output on GST and/or on
VAG 1551 scan tool Possible malfunction cause

Malfunction repair
P1340 / 17748
Camshaft/Crankshaft
Pos.Sens.Signals (B2)
Out of Sequence Harness connector on Camshaft Position
(CMP) sensor -G40- loose or corroded due to
moisture in the harness connector

- Check harness connector for tight
fit and contact corrosion, if necessary
reconnect and/or clean
P1392 / 17800
Camshaft Pos.Sensor Open
Circ. (B2)
Short to B+

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
MIL Status:
MIL lights up immediately
Wiring connection to Camshaft Position
(CMP) sensor -G40- faulty or sensor -G40-
faulty

- Check Camshaft Position (CMP)
sensor -G40- page 28
-33

For troubleshooting
Display groups 012, 014
Malfunction cause found: Yes
No
Continued next page

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
Pa
ge 155 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

No
drive, check DTC memory again

Wiring connection to ignition coil power
output stage -N122- faulty or power output
stage -N122- faulty

- Check Power output stage -N122- for
ignition coils page 28
-13


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after test
drive, check DTC memory again
MIL Status:
MIL lights up
immediately
Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
erase DTC memory and test
drive check DTC memory
Note:
The power output stage is not integrated in the Engine Control Module (ECM) -J192-, it is a separate component.
Pa
ge 158 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-117

Output on GST
and/or on VAG 1551
scan tool Possible malfunction cause

Malfunction repair
P1391 / 17799
Camshaft Pos.Sensor
(B2)
Short to Ground Harness connector on Camshaft Position
(CMP) sensor -G40- loose or corroded due
to moisture in the harness connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately Wiring connection to Camshaft Position
(CMP) sensor -G40- faulty or sensor -G40-
faulty

- Check Camshaft Position (CMP) sensor -
G40- page 28
-33


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again

Camshaft Position (CMP) sensor -G40-
oily or dirty on the inside because of leaking
seal on the cylinder head

- Remove Camshaft Position (CMP) sensor -
G40- and check for contamination. If it is
oily, replace seal on cylinder head

Malfunction cause found: Yes
No
Continued next page

- Erase DTC memory, test drive and after
test drive, check DTC memory again
Pa
ge 159 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-119

Output on GST and/or on
VAG 1551 scan tool Possible malfunction cause

Malfunction repair
P1392 / 17800
Camshaft Pos.Sensor Open
Circ. (B2)
Short to B+ Harness connector on Camshaft Position
(CMP) sensor -G40- loose or corroded due to
moisture in the harness connector

- Check harness connector for tight
fit and contact corrosion, if necessary
reconnect and/or clean
P1340 / 17748
Camshaft/Crankshaft
Pos.Sens.Signals (B2)
Out of Sequence

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
MIL Status:
MIL lights up immediately
Wiring connection to Camshaft Position
(CMP) sensor -G40- faulty or sensor -G40-
faulty

- Check Camshaft Position (CMP)
sensor -G40- page 28
-33


Malfunction cause found: Yes
No
Continued next page

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
Pa
ge 161 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

No
test drive, check DTC memory again

Wiring connection to Power output stage -
N122- for ignition coils or -N122- faulty

- Check Power output stage -N122- for
ignition coils page 28
-13


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately
Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
check DTC memory and
test drive check DTC memory
Note:
The power output stage is not integrated in the Engine Control Module (ECM) -J192-, it is a separate component.
Pa
ge 164 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-122

Output on GST and/or on
VAG 1551 scan tool Possible malfunction
cause
Malfunction repair
P1396 / 17804
Engine Speed Sensor
Missing Tooth Starter ring gear
damaged (teeth broken off)


- Remove starter and carry out visual inspection of the
starter ring gear. If broken teeth are found, replace
starter ring gear
MIL Status:
MIL lights up immediately Malfunction cause found:
Yes


- Erase DTC memory, test drive and after test drive,
check DTC memory again
For troubleshooting
Display group 037

Note:
The malfunction "P1396 / 17804" is set when the engine speed sensor does not supply 270 engine speed pulses per engine
revolution.
Pa
ge 165 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-123

Output on GST
and/or on VAG 1551
scan tool Possible malfunction cause

Malfunction repair
P1400 / 17808
EGR Valve Circ.
Electrical Malfunction Harness connector for EGR vacuum
regulator solenoid valve -N18- loose or
corroded due to moisture in the harness
connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately Wiring connection to EGR vacuum
regulator solenoid valve -N18- faulty or valve
-N18- faulty

- EGR vacuum regulator solenoid valve -
N18- page 24
-67


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again

Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
erase DTC memory and
test drive check DTC memory
Note:
The malfunction "P1400 / 17808" is set after engine start at an engine speed less than 900 RPM, an engine load less than
25% and EGR valve duty cycle less than 20%, as soon as the control module output of the EGR valve is "low" for longer than
1.2 sec.
Pa
ge 166 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1