relay AUDI A4 1997 B5 / 1.G AFC Engine On Board Diagnostic Multiport Fuel Injection Workshop Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 1997, Model line: A4, Model: AUDI A4 1997 B5 / 1.GPages: 366, PDF Size: 1.21 MB
Page 11 of 366

01-7
      
VAG 1551/1552 Scan Tool (ST), 
connecting and selecting Engine 
Electronics address word 01
 
     
Fuses for engine electronics OK 
     Fuel pump relay OK 
     Ground connections OK   page 01
-5 
    
Connecting-m.y. 1996 
-  Open back seat ash tray (center console) and remove cover for data 
link connector. 
    
-  Connect VAG 1551/1552 scan tool with adapter cable VAG 1551/3 to 
data link connector. 
Pa
ge 11 of 366 On Board Dia
gnostic 
(OBD
) - Multi
port Fuel In
jection 
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1 
Page 35 of 366

01-24
 
Diagnostic Trouble Code 
(DTC)  Malfunction text  
MIL switching 
condition  
SAE  
VAG        
P1396   17804   Engine Speed Sensor Missing Tooth   immediately  
P1400   17808   EGR Valve Circ. Electrical Malfunction   immediately  
P1402   17810   EGR Valve Circ. Short to B+   immediately  
P1407   17815   EGR Temp.Sensor Signal too Low   immediately  
P1408   17816   EGR Temp.Sensor Signal too High   immediately  
P1409   17817   Tank Ventilation Valve Electrical Malfunction   immediately  
P1410   17818   Tank Ventilation Valve Short to B+   immediately  
P1500   17908   Fuel Pump Relay Circ. Electrical Malfunction   immediately  
P1504   17912   Intake Air Sys.Bypass Air Determined   immediately  
P1505   17913   CTP Switch does not Close Open Circuit   immediately  
P1506   17914   CTP Switch does not Open Short to Ground   immediately  
P1509   17917   IAC Circ. Electrical Malfunction   immediately  
P1510   17918   IAC Circ. Short to B+   immediately  
P1511   17919   Intake Manifold Changeover Valve Circ. Electrical 
Malfunction  off  
P1512   17920   Intake Manifold Changeover Valve Circ. Short to B+   off  
Pa
ge 35 of 366 On Board Dia
gnostic 
(OBD
) - Multi
port Fuel In
jection 
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1 
Page 38 of 366

 If faulty components are found, also check wiring to the components according to wiring diagram for short and open 
circuit. 
 Before repairing or replacing components, check ground connections for Engine Control Module (ECM) -J192- connector 
D on terminals 3, 7 and 12 and connector E on terminals 3, 7 and 11 (specified value approx. 0.5  ) and ground points on 
the engine for corrosion and damage, check fuel pump relay   Repair Group 24. 
Pa
ge 38 of 366 On Board Dia
gnostic 
(OBD
) - Multi
port Fuel In
jection 
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1 
Page 53 of 366

01-40
 
Output on GST and/or 
on VAG 1551 scan tool   Possible malfunction cause  
  
Malfunction repair  
P0135 / 16519  
O2 Sensor Heater Circuit 
Malfunction (Bank 1 
Sensor 1)   Harness connector for Oxygen Sensor 
(O2S) heater -Z19- (B1-S1) loose or 
corroded due to moisture in the harness 
connector  
  
  - Check harness connector for tight fit and 
contact corrosion, if necessary reconnect 
and/or clean, installation location   page 24
-1 
  
Malfunction cause found: Yes    
No   
  
- Erase DTC memory, test drive and check 
DTC memory again 
MIL Status:  
MIL lights up immediately  
   Wiring connection for Oxygen Sensor 
(O2S) heater -Z19- (B1-S1) faulty, or heater 
-Z19- faulty  
  
  - Check O2S heater -Z19- (B1-S1)   page 24
-51
 
  
Malfunction cause found: Yes    
No   
  
- Erase DTC memory, test drive and check 
DTC memory again 
For troubleshooting   
Display group 040  
 Engine Control Module (ECM) -J192- 
faulty  
  
- Replace and code engine control module 
 page 01
-265
   erase DTC memory and 
test drive   check DTC memory 
Notes:  
 
The heating of the O2S in front of the Three Way Catalytic Converter (TWC) are switched on by the fuel pump relay.
Pa
ge 53 of 366 On Board Dia
gnostic 
(OBD
) - Multi
port Fuel In
jection 
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1 
Page 64 of 366

01-48
 
Output on GST and/or 
on VAG 1551 scan tool   Possible malfunction cause  
  
Malfunction repair  
P0155 / 16539  
O2 Sensor Heater Circuit 
Malfunction (Bank 2 
Sensor 1)   Harness connector for Oxygen Sensor 
(O2S) heater -Z28- (B2-S1) loose or 
corroded due to moisture in the harness 
connector  
  
- Check harness connector for tight fit and 
contact corrosion, if necessary reconnect 
and/or clean, installation location   page 24
-1 
  
Malfunction cause found: Yes    
No   
  
- Erase DTC memory, test drive and check 
DTC memory again 
MIL Status:  
MIL lights up immediately  
   Wiring connection for Oxygen Sensor 
(O2S) heater -Z28- (B2-S1) faulty, or heater 
-Z28- faulty  
  
  - Check O2S heater -Z28- (B2-S1)   page 24
-51
 
  
Malfunction cause found: Yes    
No   
  
- Erase DTC memory, test drive and check 
DTC memory again 
For troubleshooting   
Display group 040  
 Engine Control Module (ECM) -J192- 
faulty  
  
- Replace and code engine control module 
 page 01
-265
   erase DTC memory and 
test drive   check DTC memory 
Notes:  
The heater for the O2S in front of the Three Way Catalytic Converter (TWC) is switched on by the fuel pump relay. 
Pa
ge 64 of 366 On Board Dia
gnostic 
(OBD
) - Multi
port Fuel In
jection 
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1 
Page 123 of 366

01-92
 
Output on GST and/or 
on VAG 1551 scan tool 
  Possible malfunction cause  
  
Malfunction repair  
P1102 / 17510  
Heating Circ. (B1-S1)  
Short to B+   Harness connector for Oxygen Sensor 
(O2S) heater -Z19- (B1-S1) loose or 
corroded due to moisture in the harness 
connector  
  
- Check harness connector for tight fit and 
contact corrosion, if necessary reconnect 
and/or clean, installation location   page 24
-1 
  
Malfunction cause found: Yes    
No   
  
- Erase DTC memory, test drive and after 
test drive, check DTC memory again 
MIL Status:  
MIL lights up 
immediately  
   Wiring connection of Oxygen Sensor 
(O2S) heater -Z19- (B1-S1) faulty, or heater 
-Z19- faulty  
  
  - Check O2S heater -Z19- (B1-S1)   page 24
-51
 
  
Malfunction cause found: Yes    
No   
  
- Erase DTC memory, test drive and after 
test drive, check DTC memory again 
For troubleshooting   
Display group 040  
 Engine Control Module (ECM) -J192- 
faulty  
  
- Replace and code engine control module 
 page 01
-265
   erase DTC memory and 
test drive   check DTC memory 
Notes:  
 
|The heating of the oxygen sensor probes in front of Three Way Catalytic Converter (TWC) is switched on with the fuel 
pump relay, i.e. immediately at engine start. 
Pa
ge 123 of 366 On Board Dia
gnostic 
(OBD
) - Multi
port Fuel In
jection 
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1 
Page 131 of 366

01-99
 
Output on GST and/or 
on VAG 1551 scan tool 
  Possible malfunction cause  
  
Malfunction repair  
P1107 / 17515  
Heating Circ. (B2-S1)  
Short to B+   Harness connector for Oxygen Sensor 
(O2S) heater -Z28- (B2-S1) loose or 
corroded due to moisture in the harness 
connector  
  
- Check harness connector for tight fit and 
contact corrosion, if necessary reconnect 
and/or clean, installation location   page 24
-1 
  
Malfunction cause found: Yes    
No   
  
- Erase DTC memory, test drive and after 
test drive, check DTC memory again 
MIL Status:  
MIL lights up 
immediately   Wiring connection of Oxygen Sensor 
(O2S) heater -Z28- (B2-S1) faulty, or heater 
-Z28- faulty  
  
  - Check O2S heater -Z28- (B2-S1)   page 24
-51
 
  
Malfunction cause found: Yes    
No   
  
- Erase DTC memory, test drive and after 
test drive, check DTC memory again 
For troubleshooting   
Display group 040  
 Engine Control Module (ECM) -J192- 
faulty  
  
- Replace and code engine control module 
 page 01
-265
   erase DTC memory and 
test drive   check DTC memory 
Notes:  
 
The heating of the oxygen sensor probes in front of Three Way Catalytic Converter (TWC) is switched on with the fuel 
pump relay, i.e. immediately at engine start. 
Pa
ge 131 of 366 On Board Dia
gnostic 
(OBD
) - Multi
port Fuel In
jection 
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1 
Page 138 of 366

01-103
 
Output on GST and/or on VAG 
1551 scan tool   Possible malfunction cause  
  
Malfunction repair  
P1201 / 17609  
Cyl.1-Fuel Injector Circ.  
Electrical Malfunction  
-----------------------  
P1202 / 17610  
Cyl.2-Fuel Injector Circ.  
Electrical Malfunction  
_______________________  
P1203 / 17611  
Cyl.3-Fuel Injector Circ.  
Electrical Malfunction  
_______________________   Are all 6 fuel injectors stored in the DTC 
memory with the malfunction type "Cyl. X 
Electrical circuit electrical malfunction" and 
malfunction P1500 / 17908   
"Fuel pump relay Electrical circuit electrical 
malfunction"?  
No   
Yes 
  
- Check Fuel pump relay and 
control  page 24
-24
 
  
Malfunction cause found: Yes    
No   
  
- Erase DTC memory, test drive 
and after test drive, check DTC 
memory again 
  
 Wiring connection to Cylinder 1, 2, or 3 
  
- Check fuel injectors   page 24
-
Pa
ge 138 of 366 On Board Dia
gnostic 
(OBD
) - Multi
port Fuel In
jection 
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1 
Page 141 of 366

01-105
 
Output on GST and/or on VAG 
1551 scan tool   Possible malfunction cause  
  
Malfunction repair  
P1204 / 17612  
Cyl.4-Fuel Injector Circ  
Electrical Malfunction  
-----------------------  
P1205 / 17613  
Cyl. 5-Fuel Injector Circ  
Electrical Malfunction  
_______________________  
P1206 / 17614  
Cyl. 6-Fuel Injector Circ  
Electrical Malfunction  
_______________________   Are all 6 fuel injectors stored in DTC memory 
with the malfunction "Cyl. X-Fuel Injector Circ 
Electrical Malfunction" and with DTC P1500 / 
17908 "Fuel Pump Relay Circ Electrical 
Malfunction"?  
No   
Yes 
  
- Check fuel pump relay and 
control  page 24
-24
 
  
Malfunction cause found: Yes    
No   
  
- Erase DTC memory, test drive 
and after test drive, check DTC 
memory again 
  
 Wiring connection to Cylinder 4, 5, or 6 fuel 
  
- Check fuel injectors   page 
Pa
ge 141 of 366 On Board Dia
gnostic 
(OBD
) - Multi
port Fuel In
jection 
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1 
Page 175 of 366

01-129
 
Output on GST and/or 
on VAG 1551 scan tool   Possible malfunction cause  
  
Malfunction repair  
P1500 / 17908  
Fuel Pump Relay Circ.  
Electrical Malfunction   Wiring connection to Fuel Pump 
(FP) relay -J17- faulty, or relay -J17- 
faulty  
  
- Check Intake manifold change-over valve -N156- 
and control   page 24
-64
 
  
Malfunction cause found: Yes    
No   
  
- Erase DTC memory, test drive and after test 
drive, check DTC memory again 
MIL Status:  
MIL lights up immediately   Engine Control Module (ECM) -
J192- faulty  
  
- Replace and code engine control module   page 01
-265
   erase DTC memory and test drive   
check DTC memory 
Note:  
The malfunction "P1500 / 17908" is only stored as soon as the malfunctions "P1201 /17609", "P1202 / 17610", "P1203 / 
17611", "P1204 / 17612", "P1205 / 17613", "P1206 / 17614" are stored simultaneously. 
Pa
ge 175 of 366 On Board Dia
gnostic 
(OBD
) - Multi
port Fuel In
jection 
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1