sensor AUDI A4 1997 B5 / 1.G Brakes ESP DTC Table User Guide
[x] Cancel search | Manufacturer: AUDI, Model Year: 1997, Model line: A4, Model: AUDI A4 1997 B5 / 1.GPages: 96, PDF Size: 0.3 MB
Page 43 of 96

01-395
Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC WARNING!
This is only valid for control modules with no.: 4B0 907 389
01423
Sensor for transverse
acceleration -G200-
Sensor for transverse acceleration -
G200- not installed correctly.
Repair Manual, Brake System, Repair Group 45
- Check the installation position of the sensor for
transverse acceleration -G200-.
See continuation on
next page
There is an open circuit in one of the
supply wires for the sensor for
transverse acceleration -G200-.
Electrical Wiring Diagrams, Troubleshooting &
Component Locations - Check Ground (GND) between sensor for
transverse acceleration -G200 (terminal 1) and ABS
control module -J104- (terminal 19).
- Check voltage supply between sensor for
transverse acceleration -G200 (terminal 3) and -
J104- ABS control module (terminal 75).
Pa
ge 43 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17
Page 44 of 96

01-396
Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC WARNING!
This is only valid for control modules with no.: 4B0 907 389
01423
Sensor for transverse
acceleration -G200-
Continuation:
Open circuit in signal line to sensor for
transverse acceleration -G200-.
Short circuit to B+ or Ground (GND) in
signal line to sensor for transverse
acceleration -G200-. Electrical Wiring Diagrams, Troubleshooting &
Component Locations - Check signal line between sensor for transverse
acceleration -G200 (terminal 2) and ABS control
module -J104- (terminal 18).
Sensor for transverse acceleration -
G200- malfunctioning.
Repair Manual, Brake System, Repair Group 45
- If none of the causes listed are causing the
malfunction, replace sensor for transverse
acceleration -G200-.
See continuation on
next page Note: Only replace the control module as a
last resort.
ABS control module -J104-
malfunctioning
Repair Manual, Brake System, Repair Group 45
- If the malfunction cannot be fixed, replace the
ABS control module -J104-.
Pa
ge 44 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17
Page 45 of 96

01-397
Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC WARNING!
This is only valid for control modules with no.: 8D0 907 389, 8D0 907 389A, 8D0 907 389D
and 8D0 907 389E.
01423
Sensor for transverse
acceleration -G200-
Sensor for transverse acceleration -
G200- not installed correctly.
Repair Manual, Brake System, Repair Group 45
- Check the installation position of the sensor for
transverse acceleration -G200-.
See continuation on
next page
There is an open circuit in one of the
supply wires for the sensor for
transverse acceleration -G200-.
Electrical Wiring Diagrams, Troubleshooting &
Component Locations - Check Ground (GND) between sensor for
transverse acceleration -G200 (terminal 1) and ABS
control module -J104- (terminal 69).
- Check voltage supply between sensor for
transverse acceleration -G200 (terminal 3) and -
J104- ABS control module (terminal 67).
Pa
ge 45 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17
Page 46 of 96

01-398
Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC WARNING!
This is only valid for control modules with no.: 8D0 907 389, 8D0 907 389A, 8D0 907 389D
and 8D0 907 389E.
01423
Sensor for transverse
acceleration -G200-
Continuation:
Open circuit in signal line to sensor for
transverse acceleration -G200-.
Short circuit to B+ or Ground (GND) in
signal line to sensor for transverse
acceleration -G200-. Electrical Wiring Diagrams, Troubleshooting &
Component Locations - Check signal line between sensor for transverse
acceleration -G200 (terminal 2) and ABS control
module -J104- (terminal 18).
Sensor for transverse acceleration -
G200- malfunctioning.
Repair Manual, Brake System, Repair Group 45
- If none of the causes listed are causing the
malfunction, replace sensor for transverse
acceleration -G200-.
See continuation on
next page Note: Only replace the control module as a
last resort.
ABS control module -J104-
malfunctioning
Repair Manual, Brake System, Repair Group 45
- If the malfunction cannot be fixed, replace the
ABS control module -J104-.
Pa
ge 46 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17
Page 47 of 96

01-399
Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC WARNING!
This is only valid for control modules with no.: 4B0 907 389
01423
Sensor for transverse
acceleration -G200-
Failure in electrical
circuit
Continuation:
Open circuit in signal line to sensor for
transverse acceleration -G200-.
Short circuit to B+ or Ground (GND) in
signal line to sensor for transverse
acceleration -G200-. Electrical Wiring Diagrams, Troubleshooting &
Component Locations - Check signal line between sensor for transverse
acceleration -G200 (terminal 2) and ABS control
module -J104- (terminal 18).
See continuation on
next page
Sensor for transverse acceleration -
G200- malfunctioning.
Repair Manual, Brake System, Repair Group 45
- If none of the causes listed are causing the
malfunction, replace sensor for transverse
acceleration -G200-.
Pa
ge 47 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17
Page 48 of 96

01-400
Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC WARNING!
This is only valid for control modules with no.: 4B0 907 389
01423
Continuation:
Sensor for transverse
acceleration -G200-
Failure in electrical
circuit
There is an open circuit in one of the
supply wires for the sensor for
transverse acceleration -G200-.
Electrical Wiring Diagrams, Troubleshooting &
Component Locations - Check Ground (GND) between sensor for
transverse acceleration -G200 (terminal 1) and
ABS control module -J104- (terminal 19).
- Check voltage supply between sensor for
transverse acceleration -G200 (terminal 3) and -
J104- ABS control module (terminal 75).
See continuation on
next page Note: Only replace the control module as a
last resort.
ABS control module -J104-
malfunctioning
Repair Manual, Brake System, Repair Group 45
- If the malfunction cannot be fixed, replace the
ABS control module -J104-.
Pa
ge 48 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17
Page 49 of 96

01-401
Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC WARNING!
This is only valid for control modules with no.: 8D0 907 389, 8D0 907 389A, 8D0 907 389D
and 8D0 907 389E.
01423
Sensor for transverse
acceleration -G200-
Failure in electrical
circuit
Continuation:
Open circuit in signal line to sensor for
transverse acceleration -G200-.
Short circuit to B+ or Ground (GND) in
signal line to sensor for transverse
acceleration -G200-. Electrical Wiring Diagrams, Troubleshooting &
Component Locations - Check signal line between sensor for transverse
acceleration -G200 (terminal 2) and ABS control
module -J104- (terminal 18).
See continuation on
next page
Sensor for transverse acceleration -
G200- malfunctioning.
Repair Manual, Brake System, Repair Group 45
- If none of the causes listed are causing the
malfunction, replace sensor for transverse
acceleration -G200-.
Pa
ge 49 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17
Page 50 of 96

01-402
Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC WARNING!
This is only valid for control modules with no.: 8D0 907 389, 8D0 907 389A, 8D0 907 389D
and 8D0 907 389E.
01423
Sensor for transverse
acceleration -G200-
Failure in electrical
circuit
Continuation:
There is an open circuit in one of the
supply wires for the sensor for
transverse acceleration -G200-.
Electrical Wiring Diagrams, Troubleshooting &
Component Locations - Check Ground (GND) between sensor for
transverse acceleration -G200 (terminal 1) and
ABS control module -J104- (terminal 69).
- Check voltage supply between sensor for
transverse acceleration -G200 (terminal 3) and -
J104- ABS control module (terminal 67).
See continuation on
next page Note: Only replace the control module as a
last resort.
ABS control module -J104-
malfunctioning
Repair Manual, Brake System, Repair Group 45
- If the malfunction cannot be fixed, replace the
ABS control module -J104-.
Pa
ge 50 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17
Page 51 of 96

01-403
Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC
01423
Continuation:
Note:
Sensor for
transverse
acceleration -G200-
Implausible signal
The input signals received by ABS control module -J104- are analyzed by computing programs and
checked for plausibility. If the sensor for transverse acceleration -G200- fails, the relevant computing
program relies primarily on the steering angle sensor -G85-. If you think there is a problem with the
sensor for transverse acceleration -G200-, check whether the steering angle sensor -G85- is OK.
The steering angle sensor must also be checked.
- While driving straight ahead (v < 20 km/h), check the zero position of the steering angle sensor -
G85-, by selecting "Read measuring value block", function 08 page 01
-256
, display group 5
page 01
-270
.
- Check the sensor for transverse acceleration -G200- as described in the instructions for "Read
measuring value block" function 08 page 01
-270
, display group 5, page 01
-270
.
See continuation on
next page There are four possibilities:
Pa
ge 51 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17
Page 52 of 96

01-404
Printed output from
VAG1551 Scan Tool (ST) Possible cause
Corrective action
DTC
01423
Sensor for transverse
acceleration -G200-
Implausible signal
Continuation:
First:
The zero position of steering angle sensor -G85- is not within the specified range, and the
zero position of sensor for transverse acceleration -G200- is within the specified range:
See continuation on next
page
- Then perform zeroing procedure page 01
-243
- Erase DTC memory page 01
-15
- End Output page 01
-16
.
- Road test vehicle page 01
-250
- If the malfunction occurs again, follow the procedure for the second
case.
Pa
ge 52 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17