AUDI A4 1998 B5 / 1.G 01V Transmission Torque Tube Remove And Install Workshop Manual

AUDI A4 1998 B5 / 1.G 01V Transmission Torque Tube Remove And Install Workshop Manual A4 1998 B5 / 1.G AUDI AUDI https://www.carmanualsonline.info/img/6/1214/w960_1214-0.png AUDI A4 1998 B5 / 1.G 01V Transmission Torque Tube Remove And Install Workshop Manual

Page 1 of 10

AUDI A4 1998 B5 / 1.G 01V Transmission Torque Tube Remove And Install Workshop Manual 01-263
 
     
CAN-bus, function 
     
Bus: 
      The term "bus" refers to a system that transports 
and distributes data.  
     
CAN: 
      The Controller Area Network is a bus system that 
uses

Page 2 of 10

AUDI A4 1998 B5 / 1.G 01V Transmission Torque Tube Remove And Install Workshop Manual 01-264
 
    
6 - Power train data-BUS (CAN-bus, twisted 2 line wire)
7 - Termination resistance 
8 - Driver for BUS
9 - ABS Control Module -J104-
Pa
ge 2 of 10 CAN-
bus, function
11/20/2002 htt
p://1

Page 3 of 10

AUDI A4 1998 B5 / 1.G 01V Transmission Torque Tube Remove And Install Workshop Manual 01-265
      
Two-wire bus system, checking
 
     
If the DTC table indicates to check the bus: 
     
-  Use the applicable wiring diagram, determine 
how many control modules communicate with 
each

Page 4 of 10

AUDI A4 1998 B5 / 1.G 01V Transmission Torque Tube Remove And Install Workshop Manual 01-266
      
-  Press buttons -0- and -6- to select "End Output" 
function 06. Press -Q- button to confirm input. 
     
-  End output of scan tool by selecting the function 
"end output"   page 01
-

Page 5 of 10

AUDI A4 1998 B5 / 1.G 01V Transmission Torque Tube Remove And Install Workshop Manual 01-267
      
Two control modules communicate via a 
"two-line bus system"  
     
-  Switch ignition off.
    
 Electrical Wiring Diagrams, Troubleshooting & Component Locations    -  Disconnect both

Page 6 of 10

AUDI A4 1998 B5 / 1.G 01V Transmission Torque Tube Remove And Install Workshop Manual 01-268
 
    
If there are no malfunctions in the bus wires:  -  Check bus wires for short circuit to B+ or Ground (GND).
-  As a test, replace one of the control modules. Select a control module 
tha

Page 7 of 10

AUDI A4 1998 B5 / 1.G 01V Transmission Torque Tube Remove And Install Workshop Manual 01-269
      
Three or more control modules are 
communicating across a "two-line bus 
system"  
     
-  Analyze DTCs stored in the memories of the 
control modules. 
    
Example 1: 
From the DTCs s

Page 8 of 10

AUDI A4 1998 B5 / 1.G 01V Transmission Torque Tube Remove And Install Workshop Manual 01-270
 
    
Example 2: 
From the DTCs stored in the memories, determined that control module 2 
is not communicating with control modules 1 and 3.  
 Electrical Wiring Diagrams, Troubleshooting & Co

Page 9 of 10

AUDI A4 1998 B5 / 1.G 01V Transmission Torque Tube Remove And Install Workshop Manual 01-271
      
Example 3: 
      Using DTCs stored in the memories, determined 
that none of the control modules are sending or 
receiving signals.  
     
Control 
module  DTCs stored in DTC 
memories

Page 10 of 10

AUDI A4 1998 B5 / 1.G 01V Transmission Torque Tube Remove And Install Workshop Manual 01-272
      
-  If there are no malfunctions found in the bus 
wires, check whether one of the control modules 
is responsible for a short circuit of the bus wires 
to each other, to B+ or to Ground