sensor AUDI A4 1998 B5 / 1.G AFC Engine Fuel Supply System Components Workshop Manual

20-3

Safety precautions


WARNING!

When removing and installing the fuel pump
or fuel level sensor from a filled or partially
filled fuel tank:

BEFORE beginning repairs, the suction pipe
of an exhaust extraction system must be
located near the fuel tank opening so that
escaping fuel vapors can be immediately
carried away.
If no exhaust extraction system is available,
a radial fan (motor located outside airflow)
with volume of at least 15 m3/hr (9 cfm) may
be used.
Wear fuel-resistant gloves whenever working
with open parts of the fuel system.

Be sure the ignition is switched OFF, when:
Disconnecting fuel injection system wiring
Connecting or disconnecting test equipment
leads

BEFORE cranking the engine at starting RPM
Pa
ge 4 of 24 Fuel su
pp
ly system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.20.1

20-5

Flange and fuel level sensor, removing
and installing


Observe safety measures page 20
-3

Pay attention to rules of cleanliness page 20
-2 .

WARNING!

Fire hazard. DO NOT smoke or work near
heaters or have anything in the area that can
ignite fuel!

- Switch ignition on.

- Observe fuel gauge.

CAUTION!

The fuel tank should not be more than 2/3
full. Empty fuel tank, if necessary, using an
approved fuel cart.
Determine correct radio anti-theft coding
before disconnecting the battery.

Removing
Pa
ge 8 of 24 Fuel su
pp
ly system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.20.1

- Disconnect battery Ground (GND) strap.

- Remove cover for fuel pump module flange
(under luggage compartment trim).

- Disconnect harness connector for fuel level
sensor and fuel pump.
Pa
ge 9 of 24 Fuel su
pp
ly system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.20.1

20-6


Installing
_________________________________________________________
Front-wheel-drive vehicles:
All-wheel-drive vehicles:
_________________________________________________________ - Detach blue return line and feed line.
- Use special tool 3217 to loosen sealing ring.
- Carefully pull flange out and detach.
- Unclip fuel level sensor and remove.
- Installation is in reverse order of removal.
- Fuel level sensor wiring must be routed between return line and fuel
tank housing.
- Fuel level sensor wiring must be routed between line of fuel transfer
pump and fuel tank housing.

- When installing, make sure that arrows are aligned.
Note different alignment arrows for FRONT-wheel-drive and
QUATTRO
Pa
ge 10 of 24 Fuel su
pp
ly system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.20.1

20-7

Fuel pump, removing and installing


Observe safety measures page 20
-3

Pay attention to rules of cleanliness page 20
-2 .
Removing and installing sealing flange and fuel
level sensor page 20
-5

WARNING!

Fire hazard. DO NOT smoke or work near
heaters or have anything in the area that can
ignite fuel!

Removing

Installing
Installation is in reverse order of removal.
Note: - Insert fuel pump wrench 3307 through fuel tank opening and position at
inner part of fuel reservoir housing.
-
Turn inner part of reservoir housing about 15 to left as far as stop and
remove fuel pump along with inner part of reservoir housing.
Moisten the flange seal with fuel before installing.
Pa
ge 11 of 24 Fuel su
pp
ly system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.20.1

20-8

Front-wheel-drive vehicles

- Turn hose -7- and wiring harness -5- into position as shown at upper
left of illustration; when installing flange, turn in direction of arrow as
shown at upper right of illustration.
- Compress clamp -3- with pliers, VAG 1275.
1 - Reservoir housing
2 - Flange
3 - Clamp
4 - Securing bolt
5 - Wiring
6 - Cable strap
7 - Hose
- Install reservoir housing with flange into fuel tank.
Wiring for fuel level sensor must be routed between return line and
fuel tank housing.

- Turn flange to left until arrows (FRONT) are aligned.
Pa
ge 13 of 24 Fuel su
pp
ly system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.20.1

20-9

All wheel-drive-vehicles

- Turn hose -7- and wiring harness -5- into position as shown in upper
left of illustration; when installing flange, turn in direction of arrow as
shown at upper right of illustration.
- Compress clamp -3- with pliers VAG 1275.
1 - Reservoir housing
2 - Flange
3 - Clamp
4 - Securing bolt
5 - Wiring
6 - Cable strap
7 - Hose
- Install reservoir housing with flange into fuel tank.
Wiring for fuel level sensor must be routed between fuel transfer
pump line and fuel tank housing.

- Turn flange to left until arrows (QUATTRO) are aligned.
Pa
ge 14 of 24 Fuel su
pp
ly system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.20.1

- Remove cover for fuel pump module (under
luggage compartment trim, right rear).

- Disconnect harness connector for fuel pump and
fuel level sensor.
Pa
ge 16 of 24 Fuel su
pp
ly system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.20.1