check engine AUDI A4 1998 B5 / 1.G AFC Engine On Board Diagnostic Multiport Fuel Injection Workshop Manual

01-2
On Board Diagnostic (OBD) II technical data

Memory

Permanent memory (If the engine control module is disconnected from the permanent battery positive voltage (B+) supply,
the Diagnostic Trouble Code (DTC) memory and "Readiness Code" will be erased.)
Data output
Rapid data transfer
Additional malfunction display by Malfunction Indicator Light (MIL) lighting up
Address words
Address word 00: Automatic Test Sequence Switch ignition on or let engine idle
Address word 01: Engine Electronics Switch ignition on or let engine idle
Address word 33: OBD II Switch ignition on or let engine idle
Functions under address word 01:
Function
01: Check Control Module
Versions Switch ignition on or let engine idle
Function
02: Check DTC Memory Let engine idle, or, crank engine with starter for at least 5 sec. without
switching ignition off
Function
03: Output Diagnostic Test
Mode Switch ignition on
Pa
ge 3 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-3
Modes under address word 33:
Mode 1: Transfer diagnosis data Switch ignition on or let engine idle
Mode 2: Transfer operating conditions Switch ignition on or let engine idle
Mode 3: Check DTC memory Switch ignition on or let engine idle
Mode 4: Erase diagnosis information Switch ignition on or let engine idle
Mode 5: Output of HO2S signals Switch ignition on or let engine idle
Mode 6: Read test results (starting with control module 8D0 906 266 A) Switch ignition on or let engine idle
Mode 7: Read test results (starting with control module 8D0 906 266 A) Switch ignition on or let engine idle

Under address word 33, Mode 1 to Mode 5 can be selected starting from control module 8D0 906 266 and Mode 1 to
Mode 7 starting from control module 8D0 906 266 A.
Individual measuring values can be read under Mode 1. This is not recommended for Audi service department since this
information is available more easily under address word 01, function 04 and/or function 08.
Mode 2 shows the operating conditions under which a malfunction was recognized.
Mode 3 is used to check the DTC memory and Mode 4 is used to erase the DTC memory. In the Audi service department,
only address word 01, function 05 should be used to erase, since with Mode 4 the DTC memory is erased immediately
even if it was not checked first.
Static variables of HO2S probes, required by legal regulations, are displayed under Mode 5. Since these variables have
no direct relationship to HO2S diagnosis, Mode 5 is not needed by the Audi service department.
Pa
ge 5 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-4

Malfunction Indicator Lamp (MIL),
functions


Functional testing:
The Malfunction Indicator Lamp (MIL) must light up every time the
ignition is switched on and go out after the engine starts. If a
malfunction is recognized by the engine control module or the
transmission control module, this is indicated by the MIL lighting up. If the MIL lights up continuously, there is a malfunction present that
makes the exhaust gas worse. In this case, the DTC memory for the
engine control module and/or the transmission control module should
be checked. If the MIL starts to blink, there is a malfunction that can lead to
damage of the three way catalytic converter (e.g. combustion misfiring
with high misfiring rate). In this case, driving should only continue with
reduced power (until the MIL goes off or lights up continuously) and
the malfunction should be eliminated as quickly as possible.
- Switch ignition on: the MIL must light up. If the MIL does not light up,
check wiring according to wiring diagram and/or replace lamp.
- Start engine and let idle: MIL must go out after a couple seconds. If the
MIL does not go out after the engine starts, check DTC memory for the
engine and/or transmission control modules (malfunctions in DTC
memory).
Pa
ge 7 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-5
Malfunction recognition and repair

Notes:

Before initiating the On Board Diagnostic (OBD) program, and before testing wiring and replacing components, check the
following ground connections for corrosion and damaged connections and repair them if necessary
- Check ground connections on intake manifold
- Battery ground strap OK
- Ground cable between engine and body OK Malfunction recognition and repair is described for the VAG 1551 scan tool, since it offers significantly more functions.
However, malfunction recognition and repair is also possible with a "generic" scan tool.
A specific procedure must be used to evaluate malfunctions, since the engine electronics can be checked with address
word 01 and address word 33 on OBD II vehicles. Address word 33 can only be used to check malfunctions that have
already switched on the Malfunction Indicator Light (MIL). Address word 01 can also display the malfunctions that have
not switched on the MIL. In contrast to before, the MIL is not switched on immediately with some malfunction types, but
only after two successive trips with cold starts preceding them where the malfunction occurs. If there is a customer
complaint and/or driving performance problem, the DTC memory should be checked thoroughly with address word 01,
function 02. On vehicles with MIL lit up, the DTC memory should also be checked with address word 33, mode 3. If the
DTC memory is checked with mode 3, mode 2 should also be checked which shows the operating conditions as they were
when the malfunction was recognized.
If a malfunction is present for longer than a specified time, the malfunction is stored as a static malfunction. Malfunctions
that never or immediately switch the MIL on are set as "sporadic" at each engine start. If the malfunction occurs again, the
"sporadic" status is erased again. The "sporadic" status is erased exclusively after an OK diagnosis for malfunctions that
Pa
ge 8 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-6

The MFI control module differentiates among approx. 150 different malfunctions after evaluating the information, and
stores them until the DTC memory is erased Diagnostic Trouble Code (DTC) table, page 01
-26
.
If possible, the DTC memory should be checked with engine running.
If no malfunction is stored in the DTC memory, do not additionally erase DTC memory with function 05 since the readiness
code (if it has been set) will be erased.
The DTC memory should only be erased with function 05 since the DTC memory is erased immediately with mode 4 even
if the DTC memory was not checked before that.
If a malfunction recognized by the On Board Diagnostic (OBD) is eliminated, the following work steps should be carried
out after that:
- Erase DTC memory
- Stop engine (switch ignition off) and start it again
- Take a test drive
- Carry out automatic test sequence by inserting address word 00 Note:
Every time the DTC memory is erased (both with function 05 and with mode 4), the readiness code is reset.
Pa
ge 10 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-9

For the function:

02: Check DTC
Memory - Let engine idle, or, crank
engine with starter for at
least 5 seconds without
switching ignition off
03: Output
Diagnostic
Test Mode - Switch ignition on
04: Basic Setting
- Let engine run or switch
ignition on
07: Code Control
Module - Switch ignition on
08: Read
Measuring
Value Block - Let engine run or switch
ignition on

- Switch printer on with PRINT button (indicator
light in the button lights up).

- Press button -1- for "rapid data transfer"
operating mode.
Rapid data transfer
HELP
Insert address word XX

Indicated on display
Note:
After inserting address word 00 and pressing -Q- button to confirm input,
Pa
ge 14 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

an automatic test sequence is carried out (checks DTC memory of all
systems with rapid data transfer).
- Press buttons -0- and -1- to insert the "Engine Electronics" address
word 01.
Pa
ge 15 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-10

Rapid data transfer
Q
01 - Engine Electronics

Indicated on display
- Press -Q- button to confirm input.
Rapid data transfer Scan Tool sends address word 01

Indicated on display
_________________________________________________________
Rapid data transfer
HELP
Control module does not answer

If the following is shown on the display:
Notes:
Electrical Wiring Diagrams, Troubleshooting & Component Locations - A list of possible malfunction causes can be printed out by pressing the
HELP button.
Check data link connector/engine control module wiring connection:Engine control module faulty Diagnostic Trouble Code (DTC) table,
page 01
-26
.
Rapid data transfer
HELP
Error in communication link

If the following is shown on the display:
Notes:
Electrical Wiring Diagrams, Troubleshooting & Component Locations
On vehicles with several On Board Diagnostic (OBD) systems, check
wiring connection between the individual systems: For vehicles with only MFI (Engine Electronics) On Board Diagnostic
Pa
ge 16 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-11

Rapid data transfer
HELP
K wire not switching to Ground

If one of the following two problems is shown on the display
Rapid data transfer HELPK wire not switching to B+

Note:
Check data link connector/engine control module wiring connection:
Electrical Wiring Diagrams, Troubleshooting & Component Locations
_________________________________________________________ - A list of possible malfunction causes can be printed out by pressing the
HELP button. - After the malfunction cause is repaired, insert address word 01 again
and press -Q- button to confirm input.
8D0906266 2.8l V6/2V MFI OBD2
D01
Codin
g 01051
WSC 06388

The control module identification and the coding are shown on the
display:
Engine control module replacement part no. 8D0906266
For current engine control module version Parts catalog
Engine displacement: 2.8 liters Engine construction type: V-engine, 6-cylinderValves per cylinder: 2 valvesFuel injection system: Multiport Fuel Injection (MFI)Engine control module software version: OBD2, EPROM-status
Pa
ge 18 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-15

Rapid data transfer DTC Memor
y is erased

Indicated on display
-
Press button.
Rapid data transfer
HELP
Select function XX

Indicated on display
Note:
After address word 00 is inserted, the DTC memory of all systems with
rapid data transfer is checked. - Repair malfunctions printed out according to Diagnostic Trouble Code
(DTC) table page 01
-26
.
- After repairing the malfunctions, check DTC memory again to erase
any malfunctions that may have been stored (e.g. by disconnecting
connectors).
- Stop engine (switch ignition off) and start again.
- Test drive for at least 10 minutes.
- Carry out Automatic Test Sequence by inserting address word 00.
Pa
ge 25 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1