AUDI A4 1998 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide

AUDI A4 1998 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide A4 1998 B5 / 1.G AUDI AUDI https://www.carmanualsonline.info/img/6/941/w960_941-0.png AUDI A4 1998 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide

Page 11 of 20

AUDI A4 1998 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-57
      
Removing  
     
Engine in vehicle 
     Lock carrier must be in service position   
Page 13
-1 . 
     
-  Remove toothed belt   Page 13
-40
 .
     
CAUTION! 
     
The air conditioner

Page 12 of 20

AUDI A4 1998 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-58
 
    
-  Remove toothed belt sprocket from crankshaft. To do this, counter hold 
sprocket with 3415. 
-  Remove oil pan   Page 17
-11
    
-  Remove bolts -1 to 6-. 
-  Pry sealing flange loose

Page 13 of 20

AUDI A4 1998 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-59
 
    
WARNING!  
Wear protective glasses. 
Installing  
Note:  
The sealing flange must be installed within 5 minutes after applying 
silicone sealant.  -  Remove remaining sealant from sealing

Page 14 of 20

AUDI A4 1998 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-60
 
    
Note:  
The bead of sealant must not be thicker than 3 mm, otherwise excess 
sealant will enter the oil pan and obstruct the strainer in the oil intake line. 
Note:  
Use guide sleeve T10

Page 15 of 20

AUDI A4 1998 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-61
      
-  Install crankshaft oil seal   Page 13
-54
 .
     
-  Install toothed belt (adjust valve timing)   Page 
13
-44
 . 
     
-  Install bracket for A/C compressor -Item 5 -,   
Page 13
-1

Page 16 of 20

AUDI A4 1998 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-62
      
Dual mass flywheel/drive plate, 
removing and installing 
 
     
Dual-mass flywheel  
     
Special tools and equipment  
    
Removing  
Counter-hold tool 10-201 
    
-  Reverse positi

Page 17 of 20

AUDI A4 1998 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-63
      
Installing  
      Installation is carried out in the reverse order or 
removal; note the following:  
     
- Replace bolts. 
     
Tightening torque  
     
Component  
  
Nm  
Dual-mas

Page 18 of 20

AUDI A4 1998 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-64
      
Drive plate  
     
Special tools and equipment  
    
Removing  
Counter hold VW 558 Hex bolt M8 x 45 and two M10 hex nutsCaliper gauge or depth measure
    
-  Secure counter hold tool

Page 19 of 20

AUDI A4 1998 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-65
      
Installing  
    
-  Place drive plate in position with shim -2- and washer -1-. Lug -arrow- 
must face towards torque converter. 
-  Insert at least 3 old securing bolts and tighten to 3

Page 20 of 20

AUDI A4 1998 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate User Guide 13-66
       If nominal value is exceeded:  
    
If specified value is attained:  
Tightening torque  1) 90 corresponds to a quarter turn   -  Remove drive plate again and fit without shim -2-. Retig
Page:   < prev 1-10 11-20