lock AUDI A4 1998 B5 / 1.G Rear Brake Service Workshop Manual

46-21


Note:

Install only the complete repair kit.
The brakes can be tested on a commercial
brake dynamometer provided the speed of the
two dynamometer drive rollers is not more than
5.5 km/h (3.3 mph).
1 -
Self-locking bolt
Always replace35 Nm (26 ft lb)Counter-hold guide pin when loosening
and tightening
2 -
Brake pads Always replace as a set on both wheels of
an axle Removing and installing page 46
-24
Brake pad thickness when new: 12 mm
(0.47 in.) Brake pad wear limit (friction material): 2
mm (0.08 in.) Brake pad wear limit (including backing
plate): 7 mm (0.28 in.)
3 -
Ribbed bolt For vehicles with front wheel drive95 Nm (70 ft lb)
Pa
ge 2 of 11 Rear brakes, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.2

46-25

CAUTION!

Extract part of the brake fluid from the brake
fluid reservoir before pushing back the
pistons.
If this is not done, particularly if the brake
fluid has been topped up in the meantime,
brake fluid may flow out and cause damage.
Use the bleeder bottle or a plastic bottle,
which is used only for brake fluid, for
extracting the fluid.

CAUTION!
The repair kit contains four self-locking hex bolts which must always
be installed.
Note:
Depress the brake pedal firmly several times while the car is stationary so
that the brake pads adjust to their normal operating positions. - Install brake pads in brake carrier (arrows).
- Bolt on brake caliper housing.
Tightening torque: 35 Nm (26 ft lb)
- Install wheels and tighten wheel bolts.
Pa
ge 7 of 11 Rear brakes, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.2

46-26

Rear brake pads on front-wheel-drive
vehicles with aluminum rear brake
calipers, removing and installing


Special tools and equipment
Removing
Note:
If brake pads are to be re-used, mark installed positions when removing.
Re-install at the same point, otherwise the car may pull to one side!
3272 reset and screwout tool 3272/1 support plate
- Remove wheels.

- Counter-hold guide pins and remove self locking bolts from brake
caliper housing.
- Remove brake pads.
Pa
ge 9 of 11 Rear brakes, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.2

46-27

Installing

WARNING!

Brake fluid is poisonous and must NEVER be
removed by siphoning with your mouth.

CAUTION!

Before pushing back the piston, siphon
some of the brake fluid out of the brake fluid
reservoir. Otherwise, particularly if reservoir
has been topped off, fluid will overflow and
cause damage.
To siphon brake fluid, always use a bleeder
bottle which is only used to siphon brake
fluid.

- Screw piston inward as far as it will go by turning threaded spindle
(arrow) clockwise and knurled section counterclockwise.
Pa
ge 10 of 11 Rear brakes, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.2

46-28

- Remove protective foil from brake pad backing
plate.

CAUTION!
The repair kit contains four self-locking hex bolts which must always
be installed. - Install brake pads in brake carrier (arrows).

Note:
After installing the brake pads, depress the brake pedal firmly several
times before moving the vehicle to properly seat the brake pads in their
normal operating position. - Install brake caliper housing with new self-locking bolts and tighten.
Tightening torque: 35 Nm (26 ft lb)
- Install wheels and tighten wheel bolts.
Tightening torque: 120 Nm (89 ft lb)
- Check brake fluid level and top up if necessary.
Pa
ge 11 of 11 Rear brakes, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.2