torque AUDI A4 1998 B5 / 1.G Rear Brake Service Workshop Manual

46-22


Note:
Until changing over to ribbed bolts, the remaining
socket-head bolts should be used. Tightening
torque for the socket-head bolt is 60 Nm (44 ft lb).
3 -
Socket-head bolt
For vehicles with all wheel drive60 Nm (44 ft lb)
4 -
Brake carrier with guide pins and
protective caps Supplied as a pre-assembled replacement
part with adequate amount of grease on
guide pins If the caps or guide pins are damaged,
install repair kit Use quantity of grease from repair kit for
greasing guide pins
5 -
Ribbed bolt For vehicles with front wheel drive95 Nm (70 ft lb)
Pa
ge 3 of 11 Rear brakes, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.2

46-23


Note:
Until changing over to ribbed bolts, the remaining
socket-head bolts should be used. Tightening
torque for the socket-head bolt is 60 Nm (44 ft lb).
5 -
Socket-head bolt
For vehicles with all wheel drive60 Nm (44 ft lb)
6 -
Brake disc Always replace as a set on both wheels of
an axle To remove, first unbolt brake caliperResurface evenly on both sides starting
from thickness when new Brake disc diameter: 245 mm (9.65 in.)Brake disc thickness: 10 mm (0.39 in.)Wear limit: 8 mm (0.31 in.)
7 -
Brake caliper housing Do not disconnect brake hose when
replacing brake pads Servicing caliper 47
-13
Pa
ge 4 of 11 Rear brakes, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.2

46-25

CAUTION!

Extract part of the brake fluid from the brake
fluid reservoir before pushing back the
pistons.
If this is not done, particularly if the brake
fluid has been topped up in the meantime,
brake fluid may flow out and cause damage.
Use the bleeder bottle or a plastic bottle,
which is used only for brake fluid, for
extracting the fluid.

CAUTION!
The repair kit contains four self-locking hex bolts which must always
be installed.
Note:
Depress the brake pedal firmly several times while the car is stationary so
that the brake pads adjust to their normal operating positions. - Install brake pads in brake carrier (arrows).
- Bolt on brake caliper housing.
Tightening torque: 35 Nm (26 ft lb)
- Install wheels and tighten wheel bolts.
Pa
ge 7 of 11 Rear brakes, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.2

Tightening torque: 120 Nm (89 ft lb)
- Check brake fluid level and top up if necessary.
Pa
ge 8 of 11 Rear brakes, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.2

46-28

- Remove protective foil from brake pad backing
plate.

CAUTION!
The repair kit contains four self-locking hex bolts which must always
be installed. - Install brake pads in brake carrier (arrows).

Note:
After installing the brake pads, depress the brake pedal firmly several
times before moving the vehicle to properly seat the brake pads in their
normal operating position. - Install brake caliper housing with new self-locking bolts and tighten.
Tightening torque: 35 Nm (26 ft lb)
- Install wheels and tighten wheel bolts.
Tightening torque: 120 Nm (89 ft lb)
- Check brake fluid level and top up if necessary.
Pa
ge 11 of 11 Rear brakes, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU03.46.2