tow AUDI A4 1999 B5 / 1.G 01V Transmission Oil Pan And Oil Strainer Assembly Workshop Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 1999, Model line: A4, Model: AUDI A4 1999 B5 / 1.GPages: 44, PDF Size: 0.83 MB
Page 1 of 44
38-1
Oil pan, oil strainer and valve
body, removing and installing
WARNING!
Do not run engine with the oil pan removed or
without ATF filling and do not tow vehicle.
Notes:
Always replace a soiled or faulty valve body.
Rules of cleanliness for working on automatic
transmissions page 37
-148
.
General repair notes page 00
-27
.
Coat O-rings and sealing rings with ATF. Other
lubricating substances lead to functional
problems in the hydraulic transmission control.
Pa
ge 1 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1
Page 7 of 44
38-7
22 -
Wiring harness
Always replace page 38
-42
Transmission Fluid Temperature Sensor -
G93- is integrated into the wiring harness Remove and install valve body to install
page 38
-22
Unhook from bracket for wiring harness,
item 10 Installation position wiring harness
connector: Flat part of rear collar points
toward oil pan, the tabs at collar are
horizontal
23 -
Bolt - 6 Nm
24 -
Sensor for transmission RPM -G182- Removing and installing page 38
-36
Pa
ge 7 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1
Page 15 of 44
38-15
22 -
Wiring harness in transmission
Always replace page 38
-42
Transmission Fluid Temperature Sensor -
G93- is integrated into the wiring harness Remove and install valve body to replace
page 38
-22
Unhook from bracket for wiring harness,
item 10 Installation position wiring harness
connector: Flat part of rear collar points
toward oil pan, the tabs at collar are
horizontal
23 -
Bolt - 9 Nm
24 -
Sensor for transmission RPM -G182- Removing and installing page 38
-36
Pa
ge 15 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1
Page 30 of 44
38-30
Installing
Installation is reverse of removal, noting the
following:
- Replace O-rings.
Notes: - Insert oil line into 3381 oil line installer.
- Drive oil line into transmission housing by lightly tapping on the 3381 oil
line installer up to stop using a plastic mallet.
The open side of 3381 oil line installer faces toward the outer wall of
the transmission. Do not cant oil line. Drive in both line ends uniformly.
- Installing valve body page 38
-25
.
- Fill up ATF page 37
-140
.
- Checking oil level in front final drive page 39
-1 .
Pa
ge 30 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1
Page 31 of 44
38-31
Shift rod seal, replacing
Special tools and equipment
Removing
3385 sealing ring installer
- Removing left transmission support page 37
-125
.
- Removing Multi-Function Transmission Range (TR) Switch -F125-
page 38
-33
.
- Drive out spring dowel sleeve -1- at lever/shift rod -2- in direction of
travel toward the front (arrow), until the lever/shift rod can be pulled off
the shift rod.
Pa
ge 31 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1