sensor AUDI A4 1999 B5 / 1.G AWM Engine Oxygen Sensor Control Checking User Guide
[x] Cancel search | Manufacturer: AUDI, Model Year: 1999, Model line: A4, Model: AUDI A4 1999 B5 / 1.GPages: 46, PDF Size: 0.3 MB
Page 11 of 46
24-81
Checking primary voltage
Note:
Coolant reservoir screws must be removed and coolant reservoir must be
placed to side in order to access the harness connector. The coolant
hoses can remain connected. - Disconnect 6-pin harness connector (black) -2- to Heated Oxygen
Sensor (HO2S) -G39- before catalytic converter.
- Connect multimeter between terminal 1 and 5 for voltage
measurement.
- Switch ignition on.
Specification: 0.400 to 0.500 V
- Switch ignition off.
Pa
ge 11 of 46 Ox
yg
en sensor control, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.2
Page 12 of 46
24-82
If specified value is not obtained:
- Check oxygen sensor wiring.
If specified value is obtained:
- Replace Heated Oxygen Sensor (HO2S)-G39-
.
Checking oxygen sensor wires
Note:
Coolant reservoir screws must be removed and coolant reservoir must be
placed to side in order to access the harness connector. The coolant
hoses can remain connected. - Disconnect 6-pin harness connector (black) -2- to Heated Oxygen
Sensor (HO2S) -G39- before catalytic converter.
- Connect VAG1598/31 test box at wiring harness to Engine Control
Module (ECM), do not connect ECM Page 24
-19
.
Pa
ge 12 of 46 Ox
yg
en sensor control, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.2
Page 13 of 46
24-83
Electrical Wiring Diagrams, Troubleshooting & Component Locations
If wire connection is OK: - Check the following wire connections for open circuit.Harness connector
Terminal
VAG1598/31 test box
Socket
1 70
2 71
5 51
6 52
- Repair open circuit if necessary.- Check wires to each other for short circuit.
- Replace Engine Control Module (ECM) Page 24
-22
Pa
ge 13 of 46 Ox
yg
en sensor control, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.2
Page 14 of 46
24-84
Oxygen sensor aging, oxygen sensor
before catalytic converter, checking
Special Tools and Equipment
VAG1788/10 RPM adjuster
Test requirement:
VAS5051 with VAG5051/1Coolant Temperature at least 80 C.
Pa
ge 14 of 46 Ox
yg
en sensor control, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.2
Page 15 of 46
24-85
Test sequence
- Connect VAS5051 tester Page 01
-7 and
select vehicle system "01 - Engine electronics".
Engine must run at idle for this.
Display on VAS5051:
- In selection -1-, click on the diagnostic function "04 - Basic setting".
Pa
ge 15 of 46 Ox
yg
en sensor control, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.2
Page 16 of 46
24-86
Display on VAS5051:
1 - Enter display group Max. input value = 255
- Select function "034" in button field -2- for "display group number 034"
and press Q button to confirm input.
- Use VAG1788/10 RPM adjuster to adjust engine speed to between
2300 and 2800 RPM.
Display on VAS5051:
Note:
This process can take a few minutes. - Check specified value in display field -4-.
Pa
ge 16 of 46 Ox
yg
en sensor control, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.2
Page 17 of 46
24-87
Display fields
1 2 3 4
Display group 034: Diagnostic oxygen sensor aging
Display xxxx/min
xxx C
x.x
---
Indicated Engine speed
(RPM) Exhaust
temperature Dynamic factor Diagnostic condition
Functional
range
Test OFF
Test ON
B1-S2 OK
B1-S2 not OK
Specified value 2300 to 2800 RPM
larger than 350 C
0.5 to 2.5 B1-S2 OK
Note
If specified value is not obtained Continuation, Page
24
-88
Note for display field 2:
Calculated value from engine speed and engine load.
Note for display fields 3 and 4:
The dynamic factor is a characteristic for oxygen sensor aging. The smaller the dynamic factor, the further the oxygen sensor
aging process has advanced.
Pa
ge 17 of 46 Ox
yg
en sensor control, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.2
Page 18 of 46
24-88
Continuation
If specified value in display field 3 and 4 is not
obtained:
- Road test vehicle in order to free oxygen sensor
of possible residue and repeat test.
If specified value in display field 3 and 4 is not
obtained, even after road test:
- Replace Heated Oxygen Sensor (HO2S)-G39-
.
Pa
ge 18 of 46 Ox
yg
en sensor control, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.2
Page 19 of 46
24-89
Oxygen sensor heating, Oxygen Sensor
(O2S) Heater -Z19- before catalytic
converter, checking
Special Tools and Equipment
VAG1526A
VAG1594A
VAG1598/31
Pa
ge 19 of 46 Ox
yg
en sensor control, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.2
Page 20 of 46
24-90
Test requirements:
Coolant Temperature at least 80 C.
Fuse for oxygen sensor heating OK
Electrical Wiring Diagrams, Troubleshooting &
Component Locations
Test sequence
Note:
Coolant reservoir screws must be removed and coolant reservoir must be
placed to side in order to access the harness connector. The coolant
hoses can remain connected. - Disconnect 6-pin harness connector (black) -2- to Heated Oxygen
Sensor (HO2S) -G39- before catalytic converter.
If specified value is not obtained: - Connect multimeter between terminal 3 and 4 for resistance
measurement.
Specified value at room temperature: 2.5 to 10
Pa
ge 20 of 46 Ox
yg
en sensor control, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.2