wiring AUDI A4 2000 B5 / 1.G ATW Engine Electronic Power Control Checking Workshop Manual

24-117

Function test of warning lamp

- Switch ignition on.


The EPC warning lamp must light up for
approximately 3 seconds if there are no
malfunctions stored in DTC memory that
relate to the E-gas system

A- Fault light for power accelerator activation
-K132- does not light up

- Connect VAG1598/31 test box at wiring harness
to Engine Control Module (ECM), do not connect
ECM Page 24
-19
.

- Bridge terminals 1 and 48 at test box using wires
from VAG1594A adapter test kit.

- Switch ignition on.


Warning lamp must light up.
If warning lamp does not light up:

- Switch ignition off.

- Remove instrument cluster:
Pa
ge 6 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4

24-118

- Check following wire connection for open circuit
and short circuit to B+:

Test box
VAG1598/31
Socket
Instrument cluster

Terminal
48 Electrical Wiring Diagrams,
Troubleshooting & Component
Locations

- Repair open circuit or short circuit if
necessary.
If wire connection is OK:

- Replace Engine Control Module (ECM) Page
24
-23

Pa
ge 8 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4

24-119

B- Fault light for power accelerator activation
-K132- lights up constantly

- Check DTC memory of Engine Control Module
(ECM) Page 01
-16
.
If no DTCs are stored:

- Connect VAG1598/31 test box at wiring harness
to Engine Control Module (ECM), do not connect
ECM Page 24
-19
.

- Remove instrument cluster:

Repair Manual, Electrical Equipment, Repair
Group 90, Instrument cluster, removing and installing


- Check following wire connection for short circuit
to Ground (GND):

Test box
VAG1598/31
Socket
Instrument cluster

Terminal
48 Electrical Wiring Diagrams,
Pa
ge 9 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4

24-132

Checking wire connections

If no malfunctions are found in wires: - Pull connector -2- off throttle valve control module.
- Connect VAG1598/31 test box at wiring harness to Engine Control
Module (ECM), do not connect ECM Page 24
-19
.
- Check following wire connections for open circuit and short circuit to
Ground (GND) and B+: Harness connector
Terminal
VAG1598/31 test box
Socket
1 92
2 83
3 117
4 84
5 118
6 91
- Repair open circuit or short circuit if necessary.
- Replace throttle valve control module.
Pa
ge 25 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4

24-138

Checking wire connections

- Connect VAG1598/31 test box at wiring harness
to Engine Control Module (ECM), do not connect
ECM Page 24
-19
.

If no malfunctions are found in wires:
Repair Manual, Fuel Supply System, Repair Group 20
- Check following wire connection for open circuit and short circuit to
Ground (GND) and B+:
Harness connector
Terminal
VAG1598/31 test box
Socket
1 72
2 73
3 36
4 35
5 33
6 34
- Repair open circuit or short circuit if necessary.
- Replace accelerator pedal position sensor.
Pa
ge 32 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4

24-147
If specified values are obtained:

- Check voltage supply

Checking voltage supply

If LED does not light up:
Electrical Wiring Diagrams, Troubleshooting & Component Locations - Connect VAG1527B voltage tester as follows:Harness connector
Terminal
Measure to
1 Chassis Ground (GND)

LED must light up.
Harness connector
Terminal
Measure to
3 Chassis Ground (GND)
- Switch ignition on.

LED must light up.
- Check wire connection from terminal 1 or 3 of connector for open
circuit and short circuit to Ground (GND):
Pa
ge 43 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4

24-148

- Repair open circuit or short circuit if
necessary.
If LED lights up:

- Checking activation.

Checking activation

- Connect VAG1598/31 test box at wiring harness
to Engine Control Module (ECM), do not connect
ECM Page 24
-19
.

- Check following wire connections for open circuit and short circuit to
Ground (GND) and B+: Harness connector
Terminal
VAG1598/31 test box
Socket
2 56
4 55
- Repair open circuit or short circuit if necessary.
Pa
ge 44 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4

24-153

Checking voltage supply

If LED does not light up:
Electrical Wiring Diagrams, Troubleshooting & Component Locations
If LED lights up: - Connect VAG1527B voltage tester as follows:Harness connector
Terminal
Measure to
1 Chassis Ground (GND)
- Switch ignition on.

LED must light up.
- Check wire connection from terminal 1 of connector to fuse for open
circuit:
- Repair open circuit if necessary.
- Checking activation.
Pa
ge 50 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4

24-154

Checking activation

- Connect VAG1598/31 test box at wiring harness
to Engine Control Module (ECM), do not connect
ECM Page 24
-19
.

- Check following wire connection for open circuit and short circuit to
Ground (GND) and B+: Harness connector
Terminal
VAG1598/31 test box
Socket
2 39
- Repair open circuit or short circuit if necessary.
Pa
ge 51 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4