ignition AUDI A4 2000 B5 / 1.G AWM Engine Motronic Injection System Servicing User Guide

24-49

Test requirement:

Fuel pressure OK, checking Page 24
-32
.

Test sequence

- Remove fuel distributor including fuel injectors
from intake manifold Page 24
-45
. Fuel lines
remain connected.

- Connect VAG1598/31 test box at wiring harness
to Engine Control Module (ECM), do not connect
ECM Page 24
-19
.

Checking Proper Seal

- Bridge terminals 1 and 65 at test box using wires
from VAG1594A adapter test kit.

- Switch ignition on.


Fuel Pump (FP) must run.

- Check proper seal of fuel injectors (visual
inspection). With Fuel Pump (FP) running, only 1
to 2 drops per minute may drip out per injector.

-
If fuel loss is greater, stop Fuel Pump (FP) from
Pa
ge 53 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

running (switch off ignition) and replace faulty
fuel injector Page 24
-45
.
Pa
ge 54 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-50

Checking Injection Quantity

- Insert fuel injector to be tested in a measuring
glass from VAG1602 injection quantity test
device.

- Connect one terminal of fuel injector to engine Ground (GND) using an
adapter cable and an alligator clip from VAG1594A connector test kit.
- Connect the second terminal of fuel injector to B+ using VAG1348/3A
remote control, VAG1348/3-2 adapter cable and assisting cable.
- Bridge terminals 1 and 65 at test box using wires from VAG1594A
adapter test kit.
- Bridge terminals 1 and 65 at test box using wires from VAG1594A
adapter test kit.
- Switch ignition on.

Fuel Pump (FP) must run.
- Activate VAG1348/3A remote control for 30 seconds.
- Perform measurement on all fuel injectors.
Pa
ge 55 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-51

- After all four fuel injectors have been activated,
place measuring glasses on an even surface.


Specified value for each fuel injector: 135
10 ml

- If measured value of one or more fuel injectors
is outside of specified range, switch Fuel Pump
(FP) off (switch ignition off) and replace faulty
fuel injector Page 24
-45
.

- If the measured values of all fuel injectors are
outside the specified range, check fuel pressure
Page 24
-32
.

Note:
Also check spray pattern when checking injection
quantity. Spray pattern must be the same for all
injectors

- Install fuel injectors together with fuel distributor
Page 24
-46
.
Pa
ge 56 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-53
Component location Overview of component
locations Page 24
-5
Voltage is supplied to the Fuel Pump (FP) and
several components of the injection system via
the Fuel Pump (FP) relay -J17-.
Engine must be turning for Fuel Pump (FP) relay
-J17- to close. This means that the relay does
not receive Ground (GND) (via ECM) until the
ECM recognizes RPM signals.

Test requirement:

Battery voltage at least 12.7 V

Function test of Fuel Pump (FP) relay

- Remove driver-side storage compartment.

Repair Manual, Body Interior, Repair Group
68


- Connect VAS5051 tester Page 01
-7 and
select vehicle system "01 - Engine electronics".
Ignition must remain switched on for this.

-
Initiate output Diagnostic Test Mode (DTM)
Page 01
-51
and activate Evaporative Emission
Pa
ge 58 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-55
If specified value is not obtained:

- Replace central electronics.

Checking activation of Fuel Pump (FP) relay

- Switch ignition off.

- Connect VAG1598/31 test box at wiring harness
to Engine Control Module (ECM), do not connect
ECM Page 24
-19
.

- Switch ignition on.

- Bridge terminals 1 and 65 at test box using wires
from VAG1594A adapter test kit.

If relay triggers now, but didn't during output DTM:
If relay does not trigger:
Fuel Pump (FP) relay (at position 4 of central electronics in driver's
footwell, left) must trigger.
- Replace Engine Control Module (ECM) Page 24
-22
- Switch ignition off.
- Remove cable bridge.
Pa
ge 61 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-56


If specified value is not obtained:
Electrical Wiring Diagrams, Troubleshooting & Component Locations
If specified value is obtained: - Connect multimeter for voltage measurement as follows.Central electronicsin driver-side footwell, left,
position 4
Terminal
Measure to
19 Engine Ground
(GND)
- Switch ignition on.

Specification: approx. battery voltage
- Check wire connections.
- Check the following wire connection for open circuit and short circuit to
Ground (GND) and B+: Central electronicsin driver-side footwell, left,
position 4
Terminal
VAG1598/31 test
box


Socket
Pa
ge 63 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-68

Intake system, checking for leaks
(unmetered air)


Special tools and equipment

Notes:
Test sequence
VAS5051 with VAG5051/1Engine leak detection spray G 001 800 A1The negative pressure in the intake system sucks in the leak detection
spray with the unmetered air. Leak detection spray decreases ignition
quality and performance of the fuel mixture. This causes a reduction in
engine speed and a sharp increase of CO content. It is absolutely necessary to follow the safety precautions listed on the
can.
- Connect VAS5051 tester Page 01
-7 and select vehicle system "01 -
Engine electronics". Engine must run at idle for this.
Pa
ge 77 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-70


Display on VAS5051:
If engine speed decreases: - Make note of engine speed in display field -1.
- Spray intake system parts with engine leak detection spray in a
systematic manner.
- Check sprayed part of intake system for leaks, and eliminate the error.
-
Press "08 - erase DTC memory" to end function -button.- Select "06 - End Output"
- Switch ignition off.
Pa
ge 79 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1