AUDI A4 2000 B5 / 1.G AWM Engine Motronic Injection System Servicing Repair Manual

24-47

Make sure fuel injectors are in place and
seated correctly
Check clip for unobstructed fitting.
Place fuel rail with secured fuel injectors
onto intake manifold, and apply uniform
pressure to press it in.

Tightening torque

Component

Nm
Fuel distributor at intake manifold 10
Pa
ge 51 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-48


Injection quantity, proper seal and spray
pattern of fuel injectors, checking

Special Tools and Equipment

VAG1348/3A
VAG1594A
VAG1598/31
VAG1602
VAS5051 with VAG5051/1
Pa
ge 52 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-49

Test requirement:

Fuel pressure OK, checking Page 24
-32
.

Test sequence

- Remove fuel distributor including fuel injectors
from intake manifold Page 24
-45
. Fuel lines
remain connected.

- Connect VAG1598/31 test box at wiring harness
to Engine Control Module (ECM), do not connect
ECM Page 24
-19
.

Checking Proper Seal

- Bridge terminals 1 and 65 at test box using wires
from VAG1594A adapter test kit.

- Switch ignition on.


Fuel Pump (FP) must run.

- Check proper seal of fuel injectors (visual
inspection). With Fuel Pump (FP) running, only 1
to 2 drops per minute may drip out per injector.

-
If fuel loss is greater, stop Fuel Pump (FP) from
Pa
ge 53 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

running (switch off ignition) and replace faulty
fuel injector Page 24
-45
.
Pa
ge 54 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-50

Checking Injection Quantity

- Insert fuel injector to be tested in a measuring
glass from VAG1602 injection quantity test
device.

- Connect one terminal of fuel injector to engine Ground (GND) using an
adapter cable and an alligator clip from VAG1594A connector test kit.
- Connect the second terminal of fuel injector to B+ using VAG1348/3A
remote control, VAG1348/3-2 adapter cable and assisting cable.
- Bridge terminals 1 and 65 at test box using wires from VAG1594A
adapter test kit.
- Bridge terminals 1 and 65 at test box using wires from VAG1594A
adapter test kit.
- Switch ignition on.

Fuel Pump (FP) must run.
- Activate VAG1348/3A remote control for 30 seconds.
- Perform measurement on all fuel injectors.
Pa
ge 55 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-51

- After all four fuel injectors have been activated,
place measuring glasses on an even surface.


Specified value for each fuel injector: 135
10 ml

- If measured value of one or more fuel injectors
is outside of specified range, switch Fuel Pump
(FP) off (switch ignition off) and replace faulty
fuel injector Page 24
-45
.

- If the measured values of all fuel injectors are
outside the specified range, check fuel pressure
Page 24
-32
.

Note:
Also check spray pattern when checking injection
quantity. Spray pattern must be the same for all
injectors

- Install fuel injectors together with fuel distributor
Page 24
-46
.
Pa
ge 56 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-52


Fuel Pump (FP) relay -J17- and activation,
checking

Special Tools and Equipment

VAG1526A
VAG1594A
VAG1598/31
VAS5051 with VAG5051/1
Pa
ge 57 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-53
Component location Overview of component
locations Page 24
-5
Voltage is supplied to the Fuel Pump (FP) and
several components of the injection system via
the Fuel Pump (FP) relay -J17-.
Engine must be turning for Fuel Pump (FP) relay
-J17- to close. This means that the relay does
not receive Ground (GND) (via ECM) until the
ECM recognizes RPM signals.

Test requirement:

Battery voltage at least 12.7 V

Function test of Fuel Pump (FP) relay

- Remove driver-side storage compartment.

Repair Manual, Body Interior, Repair Group
68


- Connect VAS5051 tester Page 01
-7 and
select vehicle system "01 - Engine electronics".
Ignition must remain switched on for this.

-
Initiate output Diagnostic Test Mode (DTM)
Page 01
-51
and activate Evaporative Emission
Pa
ge 58 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

(EVAP) canister purge regulator valve -N80-.
Pa
ge 59 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-54


A - If relay does not trigger:
B - If relay triggers, but Fuel Pump (FP) does not run:
Check voltage supply of Fuel Pump (FP) relay
Fuel Pump (FP) relay (at position 4 of central electronics in driver's
footwell, left) must trigger and Fuel Pump (FP) must run.
- Check voltage supply of Fuel Pump (FP) relay Page 24
-54
.
- Checking activation of Fuel Pump (FP) relay Page 24
-55
.
- Check voltage supply for Fuel Pump (FP) and components (via Fuel
Pump -FP- relay) Page 24
-57
.
- Remove Fuel Pump (FP) relay.

- Connect multimeter to terminal 17 of relay socket and Ground (GND)
for voltage measurement.

Specification: approx. battery voltage
Pa
ge 60 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1