engine AUDI A4 2000 B5 / 1.G AWM Engine Motronic Injection System Servicing Workshop Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2000, Model line: A4, Model: AUDI A4 2000 B5 / 1.GPages: 79, PDF Size: 1.04 MB
Page 1 of 79

24-1
Motronic injection system,
servicing
Safety precautions
If special testing equipment is required during
road test, note the following:
WARNING!
Test equipment must always be secured to
the rear seat and operated from there by a
second person.
If test and measuring equipment is operated
from the passenger seat, the person seated
there could be injured in the event of an
accident involving deployment of the
passenger-side airbag.
To reduce the risk of personal injury and/or
damage to the fuel injection and ignition system,
always observe the following:
Only disconnect and reconnect wires for
injection and ignition system, including test
leads, when ignition is turned off.
If engine is to be cranked at starting RPM
without starting (e.g. for compression testing),
Pa
ge 1 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1
Page 3 of 79

24-2
It is possible that the control module will
recognize a malfunction and store a DTC during
some tests. After completing all tests and
repairs, DTC memory should therefore be
checked and erased if necessary. Readiness
code must be generated after DTC memory is
erased Page 01
-84
.
Always switch ignition off before cleaning
engine.
The battery should only be disconnected and
reconnected when the ignition is turned off,
since otherwise the Engine Control Module
(ECM) can be damaged.
WARNING!
Fuel system is under pressure! Before
opening system, place rags around the
connection point. Then release pressure by
carefully loosening connection.
Pa
ge 3 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1
Page 5 of 79

24-4
Technical data
Engine identification
AWM (1.8 L / 5V/ 125 kW-engine)
Idle speed
Engine speed cannot be adjusted, it is regulated by idle
stabilization
Front Wheel Drive
(FWD)
All Wheel Drive (AWD)
740 to 860 RPM
760 to 880 RPM
Engine speed (RPM) limitation
via fuel injector shut-off
about 6800 RPM
Fuel pressure at idle speed Vacuum hose
connected
about 3.5 bar positive pressure
Vacuum hose
disconnected
about 4.0 bar positive pressure
Residual pressure after 10 min. at least 2.5 bar positive pressure
Fuel injectors Injection stream Dual-hole nozzle / same for all
injectors
Injection quantity (30 s)
135 10 ml
Resistance
(room temperature)
12 to 13
Pa
ge 5 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1
Page 7 of 79

24-6
Repair Manual, 1.8 Liter 4
-Cyl. 5V Turbo Engine
Mechanical, Engine Code(s): AWM, Engine Code(s): AWM, Repair Group 26; Secondary Air Injection (AIR) system, checking
3 -
Oxygen Sensor (O2S) behind Three Way
Catalytic Converter (TWC) -G130-, 55 Nm
Check Oxygen Sensor (O2S) and oxygen
sensor control behind Three Way Catalytic
Converter (TWC) Page 24
-94
Check oxygen sensor heater for Oxygen
Sensor (O2S) behind Three Way Catalytic
Converter (TWC) Page 24
-107
Removing and installing Page 24
-112
4 -
Combination valve for secondary air
injection (AIR)
Checking, removing and installing:
5 -
Engine Coolant Temperature (ECT) sensor
-G62-
Checking Page 28
-31
Pa
ge 7 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1
Page 8 of 79

24-7
Repair Manual, 1.8 Liter 4
-Cyl. 5V Turbo Engine
Mechanical, Engine Code(s): AWM, Repair Group 26; Secondary Air Injection (AIR) system, checking
6 -
Fuel pressure regulator
Checking Page 24
-32
7 -
Engine Speed (RPM) sensor -G28-
Checking Page 28
-27
8 -
Secondary Air Injection (AIR) solenoid
valve-N112-
Installation location Fig. 4
, Page
24
-14
Checking:Green harness connector
9 -
Bracket for harness connectors Component location Fig. 1
, Page
24
-13
Accessible with coolant expansion tank
unbolted and swung to the side.
Pa
ge 8 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1
Page 10 of 79

24-9
Repair Manual, 1.8 Liter 4
-Cyl. 5V Turbo Engine
Mechanical, Engine Code(s): AWM, Repair Group 26; Secondary Air Injection (AIR) system, checking
13 -
E-box, plenum chamber
Installation locations Fig. 6
, Page
24
-15
Installation location for motronic Engine
Control Module (ECM) -J220- with
integrated Barometric pressure (BARO)
sensor -F96- Check voltage supply of Engine Control
Module (ECM) Page 28
-37
Procedure to follow after open circuit in
voltage supply Page 24
-21
Replacing Engine Control Module (ECM)
Page 24
-22
Installation location of Secondary Air
Injection (AIR) pump relay -J299- Check Secondary Air Injection (AIR) pump
relay -J299-: Installation location of motronic Engine
Control Module (ECM) voltage supply relay
-J271- Check motronic Engine Control Module
Pa
ge 10 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1
Page 12 of 79

24-10
Repair Manual, 1.8 Liter 4
-Cyl. 5V Turbo Engine
Mechanical, Engine Code(s): AWM, Repair Group 21, Charge air system with turbocharger, checking
14 -
Clutch vacuum vent valve switch -F36-
Component location Fig. 3
, Page
24
-14
15 -
Charge air pressure sensor -G31-
Installation location Fig. 7
, Page
24
-16
Checking:
16 -
Throttle valve control module -J338-
With throttle drive (power accelerator
actuation) -G186-, angle sensor -1- for
throttle drive (power accelerator actuation)
-G187-, and angle sensor -2- for throttle
drive (power accelerator actuation) -G188- Checking Page 24
-124
Pa
ge 12 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1
Page 14 of 79

24-12
Repair Manual, 1.8 Liter 4
-Cyl. 5V Turbo Engine
Mechanical, Engine Code(s): AWM, Repair Group 21, Charge air system with turbocharger, checking
Repair Manual, 1.8 Liter 4
-Cyl. 5V Turbo Engine
Mechanical, Engine Code(s): AWM, Repair Group 26; Secondary Air Injection (AIR) system, checking
23 -
Ignition coil
Ignition coil -N-Ignition coil 2 -N128-Ignition coil 3 -N158-Ignition coil 4 -N163-Checking Page 28
-4
24 -
Wastegate bypass regulator valve -N75-
Checking:
25 -
Mass Air Flow (MAF) sensor -G70-
Checking Page 24
-59
26 -
Secondary Air Injection (AIR) pump
motor-V101-
Checking:
Pa
ge 14 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1
Page 15 of 79

24-13
The following harness connectors are located below the coolant
expansion tank: Fig. 1 Installation location, harness connectors
1 - 4-pin harness connector, brown
for Oxygen Sensor (O2S) behind Three Way Catalytic Converter
(TWC) -G130- and Oxygen Sensor (O2S) Heater 1 -Z29- (bank 1
sensor 2)
2 - 6-pin harness connector, black
for Heated Oxygen Sensor (HO2S) -G39- beforecatalytic converter
and Oxygen Sensor (O2S) Heater -Z19- (bank 1 sensor 1)
3 - 3-pin harness connector, gray
for Engine Speed (RPM) sensor -G28-
4 - 3-pin harness connector, blue
for Knock Sensor (KS) 2 -G66-
5 - 3-pin harness connector, green
for Knock Sensor (KS) 1 -G61-
Fuel Pump (FP) Relay -J17- is located at position 4 of central electronics
in driver's footwell, left. Fig. 2 Component locations Fuel Pump (FP) Relay -J17-
Pa
ge 15 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1
Page 17 of 79

24-15
Fig. 5 Installation position, Throttle Position (TP) sensor -G79-
and sender 2 for accelerator pedal position -G185-
Fig. 6 Installation positions in E-box, plenum chamber
1 - Engine Control Module (ECM)
2 - Secondary Air Injection (AIR) pump relay -J299-
3 - Motronic Engine Control Module (ECM) voltage supply relay -J271-
4 - Installation location of fuse S130 for Secondary Air Injection (AIR)
pump
Pa
ge 17 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1