light AUDI A4 2016 Owners Manual

,....,
N
0
""' CX) ,....,
I.Cl U"I ,....,
I.Cl ,....,
.. Align the vehicle jack so the jaw@ covers the
notch and the base plate @ is flat on the floor.
The base plate @ must be
vertical under the
lift ing point @.
.. Install the rod on the vehicle jack : Insert the
rod into the opening on the handwheel. Turn
t h e rod left or right to secure it .
.. Cont inue raising the jack with the rod until the
wheel lifts off the ground slightly .
Position the vehicle jack
only under the designat­
ed lifting points on the sill~
fig. 201. There is ex­
actly
one locat ion for each wheel. The jack m ust
n ot be positioned at any other location~ &~© -
Soft gro und under the jack can cause the veh icle
to slip off the jack. Always place the jack on firm
g round . U se a flat, stable support if necessary .
Use a non-slip surface such as a r ubber mat on a
slippery surfa ce such as tile.
& WARNING
- Yo u or your passengers could be injured
whi le changing a wheel if you do not follow
these safety precautions:
- Position the veh icle jack only at the desig­
nated lifting points and align the jack .
Othe rw ise, the vehicle jac k cou ld slip and
cause an injury if it does no t have suffi­
cient hold on the vehicle .
- A soft or uns table s urface unde r the jack
may c ause the vehicle to slip off the jac k.
Always p rovide a firm base for the jack on
the ground . If necessary, use a sturdy
board under the jack .
- O n ha rd, slippery surface (such as tiles)
use a rubber mat or similar to prevent the
jack from slipping.
- To help prevent injury to yourself and yo ur
passengers:
- Do not ra ise the vehicle unt il you are sure
the jack is securely engaged.
- Passengers must not remain in the vehicle when it is jacked up.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traff ic.
Em ergen cy a ssis tanc e
-Make sure jack position is correct, adjust
as necessary and then continue to raise
the jack.
(D Note
Do not lift the vehicle by the si ll. Pos ition the
vehicle jack on ly at the designated lifting
po ints on the sill. Otherwise, your veh icle w ill
be damaged.
Taking the wheel off /installing the spare
tire
Follow these instructions step-by-step for chang­
ing the wheel.
F ig . 203 Chang ing a w hee l: us ing the screwdriver handle
(with the blade removed) to turn th e bolts
Fi g. 20 4 Cha ngin g a w heel: alignme nt pin ins ide the top
h ole
After yo u have loosened all wheel bolts and
raised the vehicle off the ground, remove and re­
place the wheel as follows:
Removing the wheel
.. Remove the topmost wheel bo lt completely
w ith the
hexagon al so cket in t he sc rewdrive r
handle (ve hicl e too l kit) ~
fig. 203 and set it
aside on a
clean surface.
243

Emergency assistance
"' Screw the threade d end of the alignment pin
from the tool kit hand-tight into the empty bolt
ho le ¢
fig . 204 .
"'Then remove the other wheel bolts as described
above.
"' Take off the wheel leav ing the a lignment pin in
the bol t ho le ¢ (D .
Putting on the spare tire
"'all road : Inf late the inflatable spare tire
¢ page239
"'Push the spare tire over the alig nment pin .
"' Screw on the wheel bo lts and tighten them
slightly using the hexagonal socke t.
"' Remove the a lignment pin and inse rt and tig ht­
en the rema ining whee l bol t slightly like the
r e st .
"'T urn the jack handle counte r-clo ckwise to lower
the ve hicl e until the jack is fully re leased .
"' Use the whee l bolt wrench to tighten all whee l
bo lts firmly ¢
page 242. Tighten them in a
crisscross pattern,
from one bolt to the (ap­
prox imately) opposite one, to keep the wheel
cente red .
"' Perform the steps req uired afte r changing th e
whee l¢
page 241, After changing a whe el.
The hexago nal soc ket makes it eas ier to remove
the wheel bolts from t he rim . Care shou ld be tak­
e n when remov ing t he revers ible b lade .
([) Note
When removi ng or installing the wh ee l, the
r im cou ld hit the brake ro tor and damage th e
rotor . Work ca refull y and have a secon d per­
so n t o help yo u.
@ Tips
- W hen mounting tir es w ith unidirectional
tread design
mak e sure th e tread pa ttern is
p oin te d t he r igh t way ¢
page 2 44.
-The w heel bol ts should b e cle an an d easy to
t urn. Check for d irt and cor ros io n on the
m at ing s urf ac es o f both t he whee l and the
hu b. Rem ove a ll di rt from th ese sur fac es b e­
f o re remo untin g t he wheel.
244
- Do not use the hexagonal socke t in the
sc rewdrive r hand le to loose n or tig hten the
wheel bol ts .
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right direction.
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a spare tire w ith a t read pattern in­
tended for use in a specif ic direction, please note
the following:
- The direction of rotation is marked by an
arrow
on the side of the tire.
- If the spare tire has to be inst alled in the inco r­
rect direction, use the spare tire on ly tempora ­
r il y since the tire will not be a ble to ac hieve its
optimum performance characterist ics with re­
gard to aquaplan ing, no ise and wear.
- We recommend that you pay part icu lar atten­
tion to th is fact d uring wet weather and that
you adjust your speed to matc h road condi­
tions .
- Rep lace the flat tire w ith a new one and have it
installed o n your veh icle as soon as possib le to
restore the hand ling advan tages of a un id irec­
t ional tire.
Notes on wheel changing
Please re ad th e inf ormati on ¢ page 224, New
t ires or w heels
if yo u are going to use a sp are tire
which is d iffe rent from the t ires on your ve hicle.
Af ter yo u cha nge a tire :
-Check the tire pressure on the spare immedi­
ately after installation .
- Have the wheel bolt t ightening torque
checked with a torque wrench as soon as pos­
sible by your authorized Audi dealer or quali­
fied workshop.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of 90
ft lb s. (120 Nm). ..,_

Fuses and bulbs
Fuses and bulbs
Fuses
Replacing a fuse
A fuse that hast blown will have metal strips
that have burned through .
Fig. 205 Left cockpit: fuse panel cover
The fuses are located at the front left and right
of the cockpit and behind the trim on the right
side of the luggage compartment.
• Switch the ignition and all electr ical equipment
off.
• Check the following table to see which fuse be­
longs to the equipment.
• Remove the appropriate cover.
• Remove the colored plastic clip from the fuse
panel, if necessary¢
page 246, fig. 206. You
can dispose of the plastic clip.
• Remove the clamp from the rear side of the
cover ¢
fig. 205 .
• Remove the fuse using the clamp.
• Replace the blown fuse only with an identical
new one.
• Install the cover.
Fuse color identification
Color Current in
amps
Black 1
Purple 3
Light brown 5
Brown 7.5
Red 10
Blue 15
Yellow 20
White or transparent 25
246
Color Current in amps
Green 30
Orange 40
A WARNING
Do not repair fuses and never replace a blown
fuse with one that has a higher amp rating.
This can cause damage to the e lectrica l sys­
tem and a fire.
(D Note
If a new fuse burns out again after shortly
have you have installed it, have the electrical
system checked by your authorized Audi deal­
er.
(D Tips
- The following table does not list fuse loca­
tions that are not used.
- Some of the equipment items listed are op­
tional or only available on certain model configurations.
Left cockpit fuse assignment
Fig. 206 Left cockpit : fuse panel with plastic clip

.... N
0
""' CX)
.... I.Cl U"I
.... I.Cl ....
Fuse panel @ (black)
No . Consumer
1 Dynamic steering
2 Electronic Stabilization Cont rol (mod ule)
A/C system press ure sensor, elect rome -
chan ica l park ing brake , Homelink, auto-
3 mat
ic dimming interior rear v iew mirror,
air q uality/outside a ir sensor, Electronic
Stabili zation Cont rol (button)
5 Sound actuator
6 Headlight range control/
headlight (cor-
ne ring light)
7 Headlight (corner ing light)
Con trol modules (e lectrom echan ica l par k-
8 ing brake , s hock ab so rbe r, q uattro s port),
DCDC converter
9 Adapt ive cru ise control
1 0 Shift ga te/clu tch se nsor
1 1 Side assist
12 Headlight range control
, p arkin g sys tem
13 Airbag
14 Rear wiper (a
llroad)
1 5 Auxiliary fuse (instrument panel)
1 6 Auxiliary fuse terminal 15 (engine area
)
Fuse panel@ (brown)
No . Consumer
2 Brake light senso r
3 Fuel pump
4 Clutch sensor
5
Left seat heating w it h /w it h out seat venti-
l a tion
6 Electronic Stabili zation Cont rol (e lectr ic)
7 Ho rn
8
F ront left door (window regulator, central
locki ng, mirror, switch, lig hting)
9 Windshield wiper moto r
10 Electronic Stabilization Cont rol (va lves)
Fuses and bulbs
No . Consumer
Two-door mode ls: rear left w indow reg ula-
1 1 tor; Four-door mode
ls: rear left door (w in-
dow regu lator, central locking, switch,
li ght ing)
1 2 Rain and
light sensor
Fuse panel © (red)
No . Consumer
3 Lumbar support
4 Dynam ic steering
5 Inter
io r ligh ting ( Cabr io let)
6 W
indshie ld washer system, headlight
wash er system
7 Vehicle e lectrica l system control module 1
8 Ve hicl e e lec trica l sy stem con trol module 1
9
Left rear window regu lator motor (Cabr io-
l et)/s unroof
1 0 Vehicle e lec tric al system con trol module 1
1 1 R
ight rear window regulator (Cabriolet)/
su n shade motor
1 2 A
nti- theft alarm warning system
Right cockpit fuse assignment
Fig. 20 7 Rig h t cockp it : f use pane l wit h plast ic cl ip
247

Fuses and bulbs
Fuse panel @ (black )
No. Consume r
5 Steering column switch module
7 Term inal 15 diagnostic connec to r
8 Gateway (Databus diagnostic interface)
9 S upplementary heater
Fuse panel @ (brown)
No. Consumer
1 C D/D VD p laye r
2 Wi-Fi
3 M MI/Radio
4 Instrument cluster
5
Ga teway (instrument cluster cont rol mod -
ule)
6 Ignition lock
7 Ligh t swi tch
8 Climate control system blower
9 Steering col umn lock
10 Climate control system
1 1 Te
rm inal 30 diagnos tic connec to r
12 Steer ing column sw itch module
248
Right luggage compartment fuse
assignment
Fig. 2 08 Right lu ggage compartment: fuse panel wit h
plast ic cl ip
Fuse panel @ (black)
No . Consumer
2 Rear wi ndow heater (Cabriolet)
3 Power top latch (Cabr io let)
4 P ower top hyd raulics (Cabr io let)
Fuse panel @ (black)
No . Consumer
Luggage compartment lid cont rol mo dule
1 ( allroad)/ Power top cont rol mod ule (Ca b-
r iolet)
2 Retractable rear
spoiler
(RS 5 Coupe)
5 E
lec tromec hanical p arking brake
6 Electronic damping contro l
7 Elec tromec hanical pa rking brake
8 Rear exte rior light ing
9 q uattro sport
10 Rear exterior lighting
1 1 Cent
ral locking
12 Terminal 30
...

..... N
0 ::..:: co ..... ..... Fuse panel© (brown)
No . Consumer
1 Luggage compartment lid control module
(allroad)
2 12-volt socket, cigarette lighter
3 DCDC converter path 1
4 DCDC converter path 2, sound amplifier,
radio
6 Right upper cabin heating (Cabriolet)
7 Elect romechan ical park ing brake
9
Right front door (window regulator, cen-
tral locking, m irror, switch, lighting)
10 Left
upper cabin heating (Cabriolet)
Two-door models: rear r ight window regu-
11 lator; Four-door models:
rear right door
(w indow regulator, central locking, switch,
lighting)
12 Cell phone prep
Fuse panel ® (black )
No . Consumer
1 Right front seat
heating
4 MMI
5 Radio
6 Rear view camera
7 Rear window heater (allroad)
8 Rear Seat Entertainment
Bulbs
Replacing bulbs
For your safety, we recommend that you have
your authorized Audi dealer replace any bulbs for
you .
It is becoming increasingly more and more diffi­
cult to replace vehicle light bulbs since in many
cases, other parts of the car must first be re­
moved before you are able to get to the bu lb.
This applies especially to the light bulbs in the
front of your car which you can only reach
through the eng ine compartment.
Sheet metal and bulb ho lders can have sharp
edges that can cause serious cuts, parts must be
Fuses and bulbs
correctly taken apart and then properly put back
together to help prevent breakage of parts and
long term damage from water that can enter
hous ings that have not been properly resealed.
For your sa fety, we recommend that you have
your authorized Audi dea ler replace any bulbs for
you, since your dealer has the proper tools, the
correct bulbs and the expertise.
Gas discharge lamps (Xenon lights)*:
Due to the high e lectr ica l voltage, have the bulbs
replaced by a qualified technician. Headlights
with Xenon light are identified by the high volt­
age sticker .
A WARNING
Changing Xenon lamps without the necessary
equipment can cause serious personal injury.
- Bulbs are pressurized and can explode when
being changed . Potential risk of injury!
- On vehicles equipped with gas discharge
bu lbs (Xenon light)* life-threatening injuries
can resu lt from improper handling of the
high -vo ltage portions of such lamps!
- Only your authorized Audi dealer or quali­
fied workshop shou ld change the bulbs in
gas discharge lamps. There are parts w ith
sharp edges on the openings and on the bulb holders that can cause serious cuts . If
you are uncerta in about what to do, have
the wor k performed by an authorized Audi
dealer or qualified workshop. Serious per­
sonal injury may result from improperly per­
formed work.
(D Tips
- If you st ill prefer to replace the light bulbs
yourself, be awa re that the engine compa rt­
ment is a hazardous area to work
inq page 203 q &,.
- It is best to ask your authorized Audi dealer
whenever you want to change a bulb.
249

Emergency situations
Emergency situations
General
This chapter is intended for trained emergency crews and working personnel who have the nec­
essary tools and equipment to perform these
operations.
Starting by pushing or
towing
CD Note
Vehicles with an automatic transmission
cannot be started by pushing or towing.
Starting with jumper
cables
If necessary, the engine con be started by con­
necting it to the battery of another vehicle.
If the engine should fail to start because of a dis­
charged or weak battery, the battery can be con­
nected to the battery of
another vehicle, using a
pair of jumper cables to start the engine.
Jumper cables
Use only jumper cables of sufficiently largecross
section
to carry the starter current safely. Refer
to the manufacturer's specifications.
Use only jumper cables with
insulated terminal
clamps which are distinctly marked :
plus(+) cable in most cases colored red
minus(-) cable
in most cases colored black.
A WARNING
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal in­
jury. Follow the instructions below for
safe
handling of your vehicle's battery.
-Always shield your eyes and avoid leaning
over the battery whenever possible.
-A discharged battery can freeze at tempera­
tures just below 32 °F (0 °C). Before con­
necting a jumper cable, you must thaw the
250
frozen battery completely, otherwise it could explode.
- Do not allow battery acid to contact eyes or
skin. Flush any contacted area with water immediately.
- Improper use of a booster battery to start a
vehicle may cause an explosion.
- Vehicle batteries generate explosive gases.
Keep sparks, flame and lighted cigarettes
away from batteries.
- Do not try to jump start any vehicle with a
low acid level in the battery.
- The voltage of the booster battery must also
have a 12-Volt rating. The capacity (Ah) of
the booster battery should not be lower
than that of the discharged battery. Use of
batteries of different voltage or substantial­
ly different "Ah" rating may cause an explo­
sion and personal injury.
- Never charge a frozen battery. Gas trapped in the ice may cause an explosion.
- Never charge or use a battery that has been
frozen . The battery
case may have be weak­
ened .
- Use of batteries of different voltage or sub­
stantially different capacity (Ah) rating may
cause an explosion and injury. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged battery.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
~page 203.
CD Note
-Applying a higher voltage booster battery
will cause expensive damage to sensitive
electronic components, such as control
units, relays, radio, etc.
- There must be no electrical contact between
the vehicles as otherwise current could al­
ready start to flow as soon as the positive
(+) terminals are connected.
@ Tips
The discharged battery must be properly con-
nected to the vehicle's electrical system. .,..

.... N
0
""' CX)
.... I.Cl U"I
.... I.Cl ....
When jump starting or charging the battery,
never connect the negative ground cable to
the battery negative post because the battery
manager system must be able to detect the
battery's state of charge. Always connect the
negative ground cable to the negat ive ground
post of the battery manager control unit .
Use of jumper cables
Make sure to connect the jumper cable clamps in
exactly the order described below!
Fig. 209 Engine compartment: Connectors for jumper ca­
bles an d charger
Fig. 210 Jump starting w ith the battery of another vehicle :
@ booster battery, ® discharged vehicle battery
The procedure described be low for connecting
jumper cables is intended to provide a jump start
for your vehicle.
Vehicle with discharged battery:
.. Turn off lights and accessories, move lever of
automatic transmission to N (Neutral) or P
(Park) and set parking brake .
Connect POSITIVE(+) to POSITIVE(+) (red)
.,. Remove the cover above the jump start connec­
t ion .
.,. Open th e cover on the positive pole
¢ fig. 209 .
Emergency situations
1. Connect one end of the red positive cab le on
the
jump start bolt¢ fig. 210 (D (Bolts un­
der cover= "positive") of the vehicle to be
started @.
2. Connect the other end to the positive termi-
nal @of the booster battery @.
Connect NEGATIVE (-) to NEGATIVE (- )
(black)
3. Connect one end of the black negative cable
to the negative terminal @ of the booster
battery @.
4. Connect the other end to the
jump start bolt
@(Bolts with hex head= "negative ") of the
vehicle to be started @.
Starting the engine
.. Start the engine of the vehicle with the booster
battery @. Run the eng ine at a moderate
speed .
.,. Start engine w ith discharged vehicle battery @
in the usual manner.
.,. If the engine fails to start: do not keep the
starter cranking for longer than 10 seconds.
Wait for about 30 seconds and then try again .
.. With engine running, remove jumper cables
from both vehicles in the exact
reverse order .
.. Close the cover on the positive pole.
The battery is vented to the outside to prevent
gases from entering the vehicle interior . Make
sure that the jumper clamps are well connected
with their
metal parts in full contact with the
battery term inals .
A WARNING
To avoid ser ious personal injury and damage
to the vehicle, heed all warnings and instruc­
tions of the jumper cable manufacturer.
If in
doubt, call for road service.
- Jumper cables must be long enough so that
the vehicles do not touch .
- When connecting jumper cables, make s ure
that they cannot get caug ht in any moving
parts in the engine compartment.
- Do not bend over the batteries -danger of
chemical bu rns!
251

Tech nical data
Gross Axle Weight Rating
The G ross Ax le We ight Rating is the max imum
load that can be applied at each axle of the vehi ­
cle ¢& .
Vehicle capacity weight
The vehicle capacity we ight (max. load) is l isted
on the d river's side 8-p illar.
_& WARNING
- T he ac tual Gross Axle Weight Rating a t the
front and rear axles sho uld not exceed the
permissible weights, and their combination
must not exceed the Gross Veh icle Weight
Rating.
Dimensions
Leng th in
(mm)
Width in
(mm)
Width (across mirrors) in (mm)
He ight (unloaded)al in (mm) -
Exceed ing permissible weight ratings can
result in vehicle damage, accidents and per­
sonal injury.
(D Note
- The vehicle capacity weight figures apply
when the load is d istr ibuted evenly in the
vehicle (passengers and luggage). When
t ransporting a heavy load in the luggage
compartment, carry the load as near to the
rea r axle as possib le so that the vehicle's
hand ling is not impaired .
- Do not exceed the max imum perm iss ible
axle loads or the maximum g ross veh icle
we ight. Always remember that the ve hicle's
han dling will be affe cted by the extra load.
T herefore, a djust your speed acco rd ingly.
- Always observe lo cal regulations.
A4Sedan S4Sedan
allroad/
A4 allroad
1 85.1 (4 70 1) 185. 7 (4716) 18 5.9 (4721)
71.9 (1826) 71.9 (1826) 72.5 (1841)
80.3 (20 40) 80.3 (20 40) 78.9 (2006)
56.2 (1427) 55.4 (1406) 58.0 (1473)
a) The height of th e veh icle depends on t he tir es and the suspens ion.
When driving up steep ramps, on rough roads,
over curbs, etc . it is important to remember that
some parts of you r vehicle, such as spoi lers or ex-
Capacities
Fuel tank: tota l capacity
Windsh ie ld a nd headlight* washer fluid conta iner
256
haust system components, may be close to the
ground. Be careful not to damage them .
gal (liters)
16.1 (61.0)
quarts (l ite rs) 4.8 ( 4.5)

Index
A
A/C (automatic climate control) . . . . . . . . . . 77
Accessories . . . . . . . . . . . . . . . . . . . . . . . 64, 260
Active lane assist
Cleaning the camera area . . . . . . . . . . . . . 194
adaptive cruise control Vehicles with manual transmission . . . . . . 99
Adaptive cruise control. . . . . . . . . . . . . . . . . . 98
Cleaning the sensor . . . . . . . . . . . . . . . . . . 194
Messages . . . . . . . . . . . . . . . . . . . . . . . . . . 105
R equ est for driver interven tio n . . . . . . . . . 103
Setting the driving program . . . . . . . . . . . 103
Adaptive dampers . . . . . . . . . . . . . . . . . . . . . 111
Adaptive light . . . . . . . . . . . . . . . . . . . . . . . . . 48
Adaptive Lig ht (defective) . . . . . . . . . . . . . . . 21
Adding Engine coolant .. .. .. ...... ... .. .. .. .
Engine oil .. .. .. .. . ... .... .. ... .. .. .
W indshield washer fluid ............. .
Additional accessories
Additives Eng ine oil .... .. .. . .. .......... .. .. .
Adjustable steer ing column .......... .. . .
Adjusting 210
207
216
260
207
80
Air distribution (automat ic climate control) .78
Instrumen t illum inat ion . . . . . . . . . . . . . . . 51
Steering column . . . . . . . . . . . . . . . . . . . . . . 80
Temperatu re (automatic climate control) . 78
Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Warning/indicator lights . . . . . . . . . . . . . . . 19
Ai rbag system . . . . . . . . . . . . . . . . . . . . . . . . 153
Advanced Airbag-System . . . . . . . . . . . . . . 142
Advanced Airbag System components . . . 144
Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Ch ildren . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Child restraints . . . . . . . . . . . . . . . . . . . . . 160
Components (front airbags) . . . . . . . . . . . 144
Danger of fitting a child safety seat on the
front passenger seat . . . . . . . . . . . . . . . . . 139
D ispos al . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Fr ont airbags . . . . . . . . . . . . . . . . . . . 142, 143
How do the front airbags work? . . . . . . . . 146
H ow many airbags does my vehicle have? 144
H ow the Advanced Airbag System compo-
nents work together . . . . . . . . . . . . . . . . . 146
Important information . . . . . . . . . . . . . . . 138
Monitoring 148
262
PASSENGER AIR BAG OFF light . . . . . . . . . 148
Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Safety instructions . . . . . . . . . . . . . . . . . . . 150
Side air bags . . . . . . . . . . . . . . . . . . . . . . . . 152
S ide curta in air bags . . . . . . . . . . . . . . . . . . 155
Warning/Indicator lights . . . . . . . . . . . . . 148
Weight-sensing mat . . . . . . . . . . . . . . . . . 159
When must the system be inspected? . . . 148
a ll- wheel drive . . . . . . . . . . . . . . . . . . . . . . . 182
All season tires . . . . . . . . . . . . . . . . . . . . . . . 232
Alternator
refer to Generator . . . . . . . . . . . . . . . . . . . . 16
Anti-freeze
refer to Eng ine coolant system . . . . . . . . . 208
Ant i-lock braking system
Warning/indicator lights . . . . . . . . . . . . 18, 19
Anti-Lock Braking System . . . . . . . . . . . . . . 177
Anti-slip regulation
Warning/indicator lights . . . . . . . . . . . . . . . 18
Anti-Slip Regulation . . . . . . . . . . . . . . . . . . . 177
Anti-theft alarm system . . . . . . . . . . . . . . . . . 31
Anti-theft systems
E le ctronic immobilizer................. 37
Armrest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Ashtray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Audi braking guard
refer to braking guard . . . . . . . . . . . . . . . . . 98
Audi drive select . . . . . . . . . . . . . . . . . . . . . . 111
Adaptive dampers . . . . . . . . . . . . . . . . . . . 111
Description . . . . . . . . . . . . . . . . . . . . . . . . . 111
Dynam ic steering . . . . . . . . . . . . . . . . . . . . 111
Setting the driving mode . . . . . . . . . . . . . . 112
Sport differential . . . . . . . . . . . . . . . . . . . . 111
Audi Se rvice Repair Manuals and Literature 258
AUTO Automatic climate control . . . . . . . . . . . . . . 78
Automa tic headl ights . . . . . . . . . . . . . . . . . 48
Automatic belt retractor . . . . . . . . . . . . . . . 133
Automatic climate control Air vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Automat ic Shift Lock (ASL) . . . . . . . . . . . . . . 92
Automatic transmission . . . . . . . . . . . . . . . . . 90
Automat ic Shift Lock (ASL) . . . . . . . . . . . . . 92
Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Eme rgency mode . . . . . . . . . . . . . . . . . . . . . 96