clock reset AUDI A4 AVANT 2008 Owners Manual

When the ignition is switched off, the odometer reading and the digital clock with date display can be switched on for a few seconds
by pressing the CHECK
button~ page 12, fig. 2 @ . •
Instrument cluster illumination
It is possible to adjust the instrument cluster illumination.
Fig. 4 In str um ent
c luster i lluminatio n
- Press the"+" button to increase the brightness .
- Press the"-" button to dim the br ightness.
A light sensor in the instrument cluster contro ls the illumina tion for
the instrument cluster, the center conso le and the displays.
The illumination for the instrument cluster lights up whenever you
sw itch on the ignition with the
vehicle h eadlight s off. As the
daylight fades, the instrument c luster illumination likewise dims
automatically and wi ll go out comp lete ly when the outside light is
very low . This feature is meant to remind you to switch on the head­
lights when the outside light conditions become poor .
•
Controls and equip­
ment
In st rum ents and w arning /indi cator li ght s
Speedometer with odometer
The speedometer shows you the vehicle speed, and the
odometer shows you how many miles (kilometers) you
have driven .
miles 1S3. 9
S2YY
Fig . 5 Sp eedom eter
c lose-u p: od omete r
di sp lay
The odometer and trip odometer are located inside the speedom ­
eter .
• USA models -Miles
• Canadian models -Kilometers
Low er odom ete r
The lower odometer shows the total number of miles (ki lometers)
d riven .
Upper odometer (tri p odometer )
The upper odometer shows the total number of miles (kilometers)
driven since you last reset the odometer to zero . You can use this
odometer when you want to keep track of how many miles (kilome ­
ters) you have driven for a single trip or errand. The last digit indi ­
cates 1/10 of a m ile (100 meters) . You can set the trip odo meter back
to zero by pressing the reset
button~ fig. 5. -..
irechnical data

will remain stored in the system until it is changed by briefly
pressing the button again or until it is reset by holding down the
button for at least two seconds. •
Speed warning 2: setting a speed limit
Switches in the wiper arm are used to operate warning
threshold 2.
Controls and equip ­
ment
Fig . 23 CHECK button
in the instrument
cluster
Fig. 24 Wiper arm:
function selector
switches
Driver information display
Saving a maximum speed
-Turn off the ignition.
-Briefly press the CHECK button in the instrument cluster
=> fig. 23 . The odometer and the digital clock will now be
illuminated.
-Press the CHECK button for at least two seconds. The
currently stored maximum speed
or the crossed out
symbol for warning 2 will appear in the display if a maximum speed has not yet been set.
Press the function selector switch in the wiper
arm @
=> fig. 24 up or down to change the set value. The values
increase or decrease in increments of 6.2 mph (10 km/h).
Resetting the maximum speed
-Turn off the ignition.
- Briefly press the CHECK button in the instrument cluster
=> fig. 23. The odometer and the digital clock will now
illuminate briefly.
-Press the CHECK button for at least two seconds. The
currently stored maximum speed will appear in the
display.
-Press the reset button in the wiper arm ©=> fig. 24 until
the display shows the symbol for speed warning 2 crossed out with a line.
The odometer and the digital clock displays will go out again a few
seconds after this adjustment is completed. •
irechnical data

Driver inf orma tion di spl ay
Several functions in your vehicle can be set, activated and
controlled by means of
Menu s. With these menus, you can addition ­
ally select which information is to be shown in the DIS (Driver Infor­
mation System) disp lay. This functions on ly with the ignit ion
switched on. Operation is controlled through the [Reset] button on
the windshield wiper
lever => page 41, fig. 29.
The
S ta rt me nu shows you the different types of d isplays:
S et
Check
Menu off
H el p•
Navigate the menu
The menu is opened using the I Reset] button and the
rocker switch on the windshield wiper lever. Inquiries and
settings are carried out.
F ig. 31 W inds hield
w ip er le ver: R es et
butt on and rocker
sw itch
[Reset] button ®=> fig. 3 1 and rock er switch @ functions
Open th e menu
- Press the [Reset) button as often as necessary until the
menu d isplay::::>
page 41, fig. 30 appears.
S elect and set
- Press the rocker switch to move to a menu display.
Sw itch operation ( up/down) resembles the disp lay .
Enter and confirm
- Press the [Reset! button.
Using the rocker switch, you can select the menus in the display or
change settings. The values selected have a red background .
By pressing the [ Reset] button, you activate the selection you made
or confirm the va lues you set. Selected functions are identified by a
check mark. •
Types of display
The DIS (Driver Information System) start menu offers a
choice am ong 4 types of displays.
The following functions reside behind the 4 types of displays in the
start
menu => page 41, fig. 30 :
Selec t se tting s
• Clock => page 43
• Computer=> page 43
• Speed alarm (speed warning) => page 35
• Tire pressure warning => page 46
• Radio display (switch on/off)
• Language
• Units (changing units of measurement for distance, fuel
consumption, time zone, temperature)

Driver information display
Select your settings as follows:
- Press the
(Reset] button:::;, page 42, fig. 31. The Start
menu
appears:::;, page 41, fig. 30.
- Press the rocker switch
:::;, page 42, fig. 31 as often as
necessary until
Set is displayed.
- Press the
(Reset] button. All the menus appear.
- Press the rocker switch until the line you want is acti-
vated (red
background):::;, page 43, fig. 33.
- Press the
(Reset] button.
-If necessary, scroll by selecting and activating the
symbol for "Next page" or "Previous page".
When you have selected the Computer menu and activated it by
pressing the
I Reset) button, two computer levels appear (computer
1 and computer
2). Now you have to select the level you want using
the rocker switch and activate it with the [Reset) button.
Continued=> page 44, "Adjust settings (part 2)". •
Adjust settings (part 2)
Continue to make your settings as follows:
- Press the rocker switch
:::;, page 42, fig. 31 until the line
you want is activated (red background).
- Now activate or deactivate the function selected by
pressing the
(Reset] button and entering a check mark -
(for "Yes") in the box or no check mark (for "No").
Press the rocker switch as often as necessary until
Back
is selected and press the (Reset) button to return to the
next higher menu level.
For several of the settings, numerical values also have to be entered,
e.g. when setting the date. This is also done by using the rocker
switch .•
Practical example (part 1)
The example shows a complete, menu-guided operation
for a setting.
Fig. 34 Display: Start
menu, Settings
selected
Fig . 35 Display :
Settings menu, clock
selected
....

To set the date, for example, proceed as follows :
- Press the [R eset] button . The Start menu appears
=> page 41, fig . 30.
- Tap the rocker
switch => page 42, fig. 3 1 until Set
=> page 44, fig. 34 is activated.
- Press the [Reset] button. The men us avai lab le under
Set
appear.
- Tap the rocker switc h unti l
Clock => page 44, fig . 35 is
disp layed .
- Press the [Reset] button . The c lock settings menu
appears .
Continued => page 45, "Practica l examp le (part 2)" . •
Practical example (part 2)
Continue w ith se tting the date as follows :
- Tap the rocker
switch => page 42, fig. 3 1 until Date is acti­
vated.
- If there a n empty box in front o f Date, press the [Reset]
button. Now a check mark appears in t he box .
- Tap the rocker switc h until the date display is activated
and press the [Reset] button. The day flashes.
- Tap the rocker switc h up or down until the correct
number for the day appears . Press the [Reset] button .
Now the month flashes.
- Chan ge the mon th and th e year as needed in the same
way.
Controls and equip ­
ment
Dri ver information di spl ay
Continued=> page 45 , "Practical example (part 3)" . •
Practical example (part 3)
Close setting the da te as follows:
- Tap the rocker
switch => page 42, fig. 31 until Back is act i­
vated.
- Press the [Reset] button. The
Set menu appears again .
- Press th e [Reset] butto n again. The Star t menu appears
agai n.•
Tire pressure monitoring system
Applies to veh ic les: with tir e pr essure monitor in g system
General notes
As an adde d safe ty feature, your vehicle has been equ ipped wit h a
tire pressure monitoring sys tem (TPMS) that i lluminates a low tire
pressure te llta le when one or more of your tires is significant ly
under-inflated . The TPMS only provides a low tire pressure warning
and does not reinflate your tires.
According ly, when the low tire pressure te llta le i llum inates, you
shou ld stop and check your tires as soon as possib le, and infla te
them to the proper pressure . Driv ing on a significantly under ­
inf lated tire causes the tire to overheat and can lead to tire failure.
Under -inflation a lso reduces fue l efficiency and tire tread life, and
may affect the vehicle 's hand ling and stopping ab ility .
0 Note
• Please note that the TPMS is not a substitute for proper tire
maintenance , and it is the driver's responsibility to maintain correct
..,_

___ C_ h_ e_c _k_ i_n ~g _ a_n_ d_ f_ il _li_ n~ g~--------------------------------------------
For example, a charging current of 4.5 amps would be used on a
battery rated at 45 Ah. Rated capacity of the battery in your vehicle
is listed on the battery housing .
The battery caps should
not be opened when charging a battery.
& WARNING
Charging a battery can be dangerous.
• Always follow the operating instructions provided by the
battery charger manufacturer when charging your battery.
• Never charge a frozen battery . It may explode because of gas
trapped in the ice. Allow a frozen battery to thaw out first.
• Do not reuse batteries which were frozen. The battery housing
may have cracked and weakened when the battery froze.
• Charge the battery in a well ventilated area. Keep away from
open flame or electrical spark. Do not smoke. Hydrogen gas gener ­
ated by the battery is explosive.
• To reduce the danger of explosion, never connect or disconnect
charger cables while the charger is operating.
• Fast charging a battery is dangerous and should only be
attempted by a competent technician with the proper equipment.
• Battery acid that may spill during charging should be washed
off with a solution of warm water and baking soda to neutralize
the acid.
0 Note
Never use a fast charger as a booster to start the engine . This will
seriously damage sensitive electronic components, such as control
units, relays, radio, etc ., as well as the battery charger. •
Disconnecting and connecting the battery
When the battery is disconnected some features on the
vehicle will become inoperative and you must reset them
when the battery is reconnected.
When you disconnect the vehicle battery note the following:
• some data stored in the driver information system is erased,
• the clock stops,
• the factory installed radio locks up,
• the engine management system and the one-touch-up and one­
touch -down functions of the power windows no longer work .
After you reconnect the battery, you must reset the following
features :
Inoperative because the
battery was discon­
nected:
clock
one-touch-up and one-touch­
down feature on the power
windows
engine management
seat memory*
radio station coding
Removing battery
To reset after the battery is
reconnected, see:
=> page 14
=> page 67
=> page 135
=> page 100
Sound System Operating Instruc -
tions booklet .
•
Before you check anything in the engine compartment,
always
read and heed all WARNINGS :::> & in "Working in
the engine compartment" on page
273. ~

___ A_,_ lp_h_ a_b_ e_ t
_ i_ c _ a_ l_ in_ d_ e_x ______________________________________________ _
Parking brake warning ..... .. .... .... . 29
Parking l ight
Defective . . . . . . . . . . . . . . . . . . . . . . . . 35
Park ing on a dec line (downhil l) ....... 138
Parking on an incline (uphill) ..... .... 138
Parktronic
See acoustic park assist . . . . . . . . . . . 139
Parts replacement . . . . . . . . . . . . . . . . . . 348
PASSENGER AIR BAG OFF light ........ 199
Passive safety system . . . . . . . . . . . . . . . 166
Pedals ............................ 172
Physical principles of a fronta l collision 177
Polishing . . . . . . . . . . . . . . . . . . . . . . . . . . 257
Power locking switch . . . . . . . . . . . . . . . . . 59
Rear ............................ 60
Power locking system . . . . . . . . . . . . . . . . 55
Convenience close/open feature ..... 59
Locking and unlocking the vehicle from
inside ........... ....... .... .... 59
Opening and c losing the windows ... 59
Operating locks from with key .. .... 58
Rear lid . .... ... .. .... .... .... .... 61
Remote control . . . . . . . . . . . . . . . . 53, 56
Unlocking and locking vehicle ....... 56
Power locks
Power sunroof ..... .... .... .... ... 69
Pow er outlets . . . . . . . . . . . . . . . . . . . . . . 121
Power roof ........ .... ... .. .... ..... 67
Power seats Adjusting the seatback ............. 99
Adjustment ........... .... .... ... 97
Pow er steering . . . . . . . . . . . . . . . . . 135 , 241 Power
sunroof
Emergency closing ................ 69
Power window switche ·s . ...... .... ... 65
In the driver's door ... .... ... .. .... 66
In the front passenger's door ....... 67
Reactivating the system ............ 67
Pregnant women Specia l considera tions when wearing a
safety belt . . . . . . . . . . . . . . . . . . . . . 183
Programming the Homelink® Universa l Re -
mote Contro l . . . . . . . . . . . . . . . . . . . 157
Prop er occupant seating positions .... 168
Proper safety be lt position . . . . . . . . . . . 182
P roper seating position
Front passenger . . . . . . . . . . . . . . . . . 169
Occupants . . . . . . . . . . . . . . . . . . . . . . 168
Rear passengers . . . . . . . . . . . . . . . . . 170
Protectiv e liner 113
a
Quartzclock ...... .... ........ ....... 14
quattro®
See All -whee l drive ............... 242
Question
R
What happens to unbelted occupants? ..
178
Why safety belts? . . . . . . . . . . . . . . . . 176
Radiator fan ...... ............. ..... 283
Radio Replacing ....................... 349 Rain sensor defective
... .. .... .... .... 34
Reading lights
Front ....... ...... .... ...... ..... 81
Rear .......................... 81, 82
Reararmrest . .... .... .... ....... ... 103
Rear ashtray ....................... 119
Rear fog lights .. ...... .... .... .... ... 76
Rear lid
Emergency un locking (on ly manually . 62
Locking/unlocking ............. .... 61
Rear light
Defective ........ .... .... .... .... . 35
Rear power locking switch ... .. .... .... 60
Rear seat bench .. .... .... ..... .. ... 104
Rear view mirror Inside rear view mirror ............. 90
Rear window defogger .... .... .... ... 131
Rearview mirror
See Mirrors ....................... 90
Red symbols .. ........... .... .... ... 30
Refuel ling .......................... 269
Release lever for hood .... ........ ... 272
Remote control . . . . . . . . . . . . . . . . . . . 53, 56
Assigning a seat position .. .... .... 102
Resetting remote control ........... 57
Unlocking and locking ............. 56
Remote master key
Battery replacement ....... ....... . 53
Check light ................ ...... . 53
Remote rear lid release .... ...... ..... 63
Removing luggage compartment cover/parti -
tion net ...... .... .... .... .... . 111