change wheel AUDI A4 CABRIOLET 2009 Owner's Manual

11111...__W_ h_ a_ t_d_ o_ l _d _o_ n_ o_ vv_ ? ______________________________________________ _
& WARNING
• Using force without control to speed the wheel change up can
cause the vehicle to slip off the jack and cause serious personal
injuries.
• Do not loosen the wheel bolts more than one turn before you
raise the vehicle with the jack. -Risk of injury!
[ i ] Tips
• Never try and use the hexagonal socket in the handle of the
screwdriver to loosen or tighten the wheel bolts.
• If a wheel bolt sits very tight, you may find it easier to loosen by
carefully pushing down on the end of the wheel bolt wrench with
one foot only . As you do, hold on to the car to keep yourself stable
and take care not to slip.•
Raising the vehicle
The vehicle must be lifted with the jock first before the
wheel con be removed.
N
"' ~ I
"' al
Fig . 219 Wheel
change : mounting
points for the lifting
jack Fig
. 220 Close-up:
proper positioning of
lifting jack
- Position the jack below the door sill under the mounting
point
that is closest to the wheel to be changed
~ fig. 219.
- Turn the
jack handle clockwise until the jack arm just fits
underneath the rib running along the underbody
~ &,.
- Align the jack so that the jack arm claw~ fig. 220 @fits
snugly around the underbody rib and the movable base
plate ® sits flat on the ground.
- Wind the jack up further until the flat wheel comes off the
ground~ &-
Recesses at the front and rear of the underbody rib mark the proper
mounting locations for the jack => fig. 219. There is only one desig­
nated jack mounting point for each wheel. Do not apply the jack
anywhere else=>& .
The jack should be positioned approximately 6 in. (15 cm) behind
the front wheel or 10 in. (25 cm) in front of the rear wheel.
An
unstable surface under the jack can cause the vehicle to slip off
the jack . Always provide a firm base for the jack on the ground. If
necessary place a sturdy board or similar support under the jack. On
hard, slippery surfaces (such as tiles) use a rubber mat or similar to
prevent the jack from slipping=>& . .,,

_____________________________________________ W_ h_ a_t _d_ o _ l _d_o _ n_o_ w_ ? _ __,_
& WARNING
• You or your passengers could be injured while changing a
wheel if you do not follow safety precautions:
-Mounting the jack under the vehicle at any other place than
indicated above may damage the vehicle or may result in
personal injuries.
- A soft or unstable surface under the jack may cause the
vehicle to slip off the jack . Always provide a firm base for the
jack on the ground.
If necessary , use a sturdy board under the
jack .
- On hard, slippery surface (such as tiles ) use a rubber mat or
similar to prevent the jack from slipping .
• To help prevent injury to yourself and your passengers :
- Do not raise the vehicle until you are sure the jack is securely
engaged.
- Passengers must not remain in the vehicle when it is jacked
up.
- Make sure that passengers wait in a safe place away from
the vehicle and well away from the roadway and traffic .
- Make sure jack position is correct , adjust as necessary and
then continue to raise the jack. •
Taking the wheel off /putting the spare on
Follow thes e instru ctions s tep-by -step for chang ing the
wheel
Fig . 2.21 Wheel
change : using the
screwdriver handle
( with the blade
removed) to turn the
bo lts
Fig .
222 Wheel
change : alignment pin
inside the top hole
Af te r yo u h ave l oo sened a ll wheel b olts and jacked the
vehicle off the gr ound, perform the fo llow ing steps to
remove and repla ce t he wheel:
Removing the wheel
Use th e hexagonal socket in the screwdriver handle t o
comple te ly turn ou t the t opmos t whe el b olt an d set i t
as ide on a
cl ean surfac e~ fig. 221. ..,
~ehicle care Do-it-yourse lf service irechnical data

1111.___W_ h_ a_ t_d_ o_ l _d _o_ n_ o_ w_ ? ______________________________________________ _
-Screw the threaded end o f the alignment pin from the
tool kit hand -tight into t he now vacant bo lt hole
=>
page 297, fig . 222.
- Then completely unscrew the other wheel bolts as
described above .
- Take off the wheel leaving the alignment p in in the bolt
hole.
Puttin g on th e sp are
- Lift the spare wheel up and carefu lly s lide it over the
alignment pin to gu ide it in place .
- Use t he hexagonal socket in the screwd river handle to
screw in and tighten all w heel bolts
slightly.
- Unscrew the alignment pin and insert and tighten the
remaining w heel bolt slightly like the rest.
- Turn the handle on the jack counter-clockwise to lower
the vehicle until the jack is fully released.
- Use the wheel bo lt wrench to tighten all wheel bo lts
firmly=>
page 295. Tighten crosswise, from one bolt to
the (approx imately) oppos ite one, to keep the wheel
centered.
[ i ] Tip s
Never try and use the hexagona l socket in the handle of the screw­
driver to loosen or tighten the wheel bolts.
• Pull the reversible b lade from the screwdriver before you use the
hexagonal socket in the handle to turn the wheel bo lts.
• When mounting tires with
uni dire cti on al tread desig n make sure
the tread pattern is pointed the right way~
page 298.
• The whee l bolts should be clean and easy to turn. Check for dirt
and corrosion on the ma ting surfaces of both the wheel and the
hub. Remove all dirt from these surfaces before remounting the
wheel. •
Tires with unidirectional tread design
Tires with unidirectional tread design must be mounted
with their tread pattern pointed the right direction.
U sin g a spa re tire wit h a tre ad p atte rn int ended for u se
i n a sp ec ific dir ection
When using a spare tire with a tread pattern intended for use in a
specific direction, please note the following:
• The direction of rotation is marked by an arrow on the side of the
tire.
• If the spare tire has to be installed in the incorrect direction in the
event of a flat tire, use the spare tire on ly temporarily since the tire
will not be able to achieve its optimum performance characteristics
with regard to aquaplaning, noise and wear.
• We recommend that particular attention be paid to this fact
dur ing wet weather and that you adjust your speed to match road
conditions.
• Replace the flat tire with a new one and have it instal led on your
vehic le as soon as possible to restore the handling advantages of a
proper ly pointed direction-dependent tire. •
Notes on wheel change
Please read the information~ page 279, "New tires and replacing
tires and whee ls", if you are going to use a spare tire which is
different from the tires on your veh ic le.
After you change a tire: .,_

llftl __ D_a_ t_ a ___________________________________________________ _
Data
Applies to vehi cles : w ith 2.0 lite r 4-cyl. engi ne
200 hp, 2.0 liter 4-cyl. turbo engine
En gin e da ta
Maximum output SAE net
Maximum torque SAE net
No . of cylinders
Disp lacement
Stroke
Bore
Compression ratio
Fuel
Dimen sion s (a pprox.)
Length (with licence plate bracket)
Width (across mirrors) Height (unladen)
Turning circle diameter (curb to curb)
Ca paci ties (a pprox.)
Fuel ta nk
-Total capacity
- Reserve (of total capacity)
Wind shield and h eadlight washer fluid containe r
Eng ine oil
with filter change hp@rpm
lb
-ft@ rpm
CID (cm
3 )
in (mm)
in (mm)
200 @ 5100 -6000
207
@ 1800-5000
4 121 (1984)
3.65 (92.8)
3 .25 (82 .5)
10.5: 1
Premium unleaded (91 AKI! Recommended for maximum eng ine performance . Fur­
ther details =:,
page 244, "Gasoline"
in (mm)
in (mm)
in (mm)
ft. (ml
180 (4573)
76.2 (1937) 54.8 (1391)
36.4 (11.1)
gal/litres
gal/litres
qua rts/1 it res
quarts/litres
front -wheel drive
18.5 / 70 .0
2.1 / 8.0
4.8
I 4.5
4.8
I 4.5
quottro
16.6 / 63_0
•

___ C_ o_n_ s_ u_m _ e_ r_ ln_ f_o _r_m _ a_ t_ i_o _n ______________________________________________ _
& WARN ING (continued )
• The engine compartment of any motor vehicle is a potentially
hazardous area . Never reach into the area around or touch the
radiator fan . It is temperature controlled and can sw itch on
suddenly -even when the engine is off and the ignition key has
been removed . The radiator fan switches on automatically when
the coolant reaches a certain temperature and will continue to run until the coolant temperature drops .
• Always remove the ignition key before anyone gets under the
vehi cle .
• Always support your vehicle with safety stands if it is neces ­
sary to work underneath the vehicle . The jack suppl ied with the
vehicle is not adequate for this purpose and could collapse causing serious personal injury .
• If you must work underneath the vehicle with the wheels on
the ground, always make sure the veh icle is on level ground , that
the wheels are always securely blocked and that the engine
cannot be sta rted .
• Always make sure the transmission selector lever (automatic
transmission) is in "P " (Park position ) or Neutral (manual transm is­
sion) and the park brake is firmly applied.
W For the sake of the environment
• Cha ng ing t he e ngine sett ings will adverse ly aff ect em iss ion
l eve ls. This is detrimenta l to the environment and increases fuel
co nsu mp tio n .
• Always observe environmental regu lations when disposing of
ol d eng ine oil, u sed br ake fluid , d irty e ngin e coo la nt , spe nt batter ies
or worn out tires.
• Undeployed airba g modu les and prete nsioners might be classi ­
fied as Perchlorate Material -specia l handling may apply, see
www .dtsc.ca .gov/ hazar douswaste/perc hlorat e. When the vehic le o r
parts of the restraint system including airbag modules safety be lts
w it h pr eten sion ers ar e sc ra p pe d, a ll ap pli cab le la w s and reg ula- tions must be observed. Your authorized Audi dealer is familiar with
t
hese requi re m ents and we re co m mend th at you h ave your dealer
perform this service for you .•
Additional accessories,
modifications and parts replacement
Additional accessories and parts
replacement
Always consult an author ized Audi dealer before
pu rchasin g acc ess ori es.
Your vehicle incorporates the latest safety design features ensuring
a high standa rd o f act ive and passiv e safety .
T his saf ety coul d be compromised by non -approved changes to the
vehic le . F or t his reason, if parts have to be replace d, p lease obse rve
t h e f ollow ing po ints when i nsta lling addi tio na l acc essor ies:
App roved Aud i accessories and genuine Audi pa rts a re avai lab le
fr om autho rize d Aud i dea lers.
T hese dealers also have the necessary fac ilities, tools and trained
spec ia lists t o ins tal l the part s and accessor ie s pr oper ly .
& WARNING
Using the wrong spare parts or using non -approved accessories
can cause serious personal injury.
• Use only accessorie s expressly approved by Audi and genuine
Audi spare parts.
• These parts and accessories have been specially designed to
be used on your vehicle .
• Never install accessories such as telephone cradles or
beverage holders on airbag covers or within the airbag deploy-

Alph ab eti ca l ind ex -____________ _,_ __ _
Trailer towing .. ... .... ..... .. .. ... . 224
Operating instructions ....... .... . 225
Technical requirements ....... 224 , 225
Trailer tow ing tips ................ 226
Transmission tiptronic® .... ... ... ..... .... .... 126
Transport Canada ... .... .... ...... .. 155
Tread Wear Indicator
(TWll ........... 278
Trip computer Fuel consumption .... .... ... .... .. 37
Mileage .. .... ..... .. .... ...... ... 37
Trip odometer . ...... .... ...... .... .. 15
What does it mean when dEF appears in
the trip odometer display? ......... 15
Trunk Escape handle .. .... .... ......... 290
Trunk lid
See Rear lid .... .. .... ...... .... ... 55
Turn signals . .............. .......... 83
Warning/indicator lights ... ......... 21
u
Undercoating ..... .. .... .... ... .... . 237
Unfastening safety belts ... .... .... .. 165
Unidirectiona l tires ...... ...... .... .. 267
Uniform tire quality grading .. ..... ... 283
Universal Remote Control (Homelink®l . 139
Unlocking Power locking switch .............. 54
Rear lid . ... .. .... .... ...... ...... 55
Remote control .. .. .... .... .... ... 51
Using the key . ... .. .. .... ...... ... 53
Controls and equip­
ment Safety first
V
Vanity
mirror .... ..... ........ ..... .. 84
Vehicle electrical system ....... .... ... 22
Vehicle Identification !Number (VIN) .... 312
Vehicle jack .................... 290, 296
Vehic le literature .. .... ... .. ...... ... .. 5
Vehicle -care products .... .... .... .... 230
w
Warning lights ....................... 18
Warning/indicator lights .... .... ....... 12
Airbag system ............ .... .... 20
Anti-lock brake system (ABS) ... ..... 20
Brake system ....... .... .... ..... . 23
Cruise control .... ... .... .... .... .. 20
Electronic power control ............ 22
Electron ic stabil ization program (ESP) 22
Generator .. ........ .... ... .. .... . 22
High beam . .... ........... .... ... 22
Malfunction lndica11:or Lamp (Mill . ... 19
Parking brake ...... .... ....... .... 23
Power top .... ...... .... .... . ... .. 21
Safety belt ... ....... .. .. .... .... .. 21
Tire pressure monitoring system ..... 20
Turn signals .. ..... .. .... .... .... . 21
Warranty coverages ........... .... .. 316
Washing ..................... ...... 230
Automatic car wash ... ...... .... .. 231
by hand ......................... 231
Power top cleaning ......... ..... . 233
w ith a power washer .............. 232 Washing
the vehicle .... .... ... .. .. .. 230
Waxing .... .... .... ... .. ...... .... . 233
Wear indicator ...................... 278
Weatherstrips .... ... .... .... .... ... 236
Weights .... .... ... .. .... ...... ..... 313
What happens if you wear your safety belt too
loose? . .... .... ... .. ...... .... . 164
What happens to unbelted occupants? . 161
What impairs driving safety? .......... 147
What should I do after changing a wheel? . .
275
What should I do after replacing whee ls?
275
Wheel bolts Torque ..... .... .... .... .... ..... 286
Wheel change .... .... ... .... .... ... 293
Wheels .. .. .. .......... ....... ..... 267
Cast a lloy ..... ... ..... ...... ... .. 237
Checking tire pressure ............ 274
Cold tire inflation pressure . .... .... 271
Genera l notes .. .... ... .... .... ... 267
G lossary of t ire and loading terminology
268
New tires and wheels ........ .... . 279
Rim ............................ 267
Steel whee ls ..................... 236
Tires and vehicle load limits ........ 275
When must a safety belt be replaced? .. 162
When must the airbag system be inspected? 179
When should I adjust the tire pressures? ...
275
When should I check the tire pressures? 275
Vehicle operation Vehicle care Do-it-yourself service Technical data