service AUDI A5 CABRIOLET 2011 Owners Manual

Fuses and bulbs Ill ___________________ ...:......:.;...:...,:_.;__...;___--
Right luggage comp artment fuse
assignment
Fig. 2 47 R igh t luggage compartment: fuse panel wit h plastic cl ip
N o. Con sum er
Fu se pane l@ (bl ac k)
1 Power top control module
2 T railer control module
3 Trailer control module
4 Trailer control module
Electromechanical parking brake
Electronic damping control
7 Electromechanical parking brake
8 Veh icle elect rical system contro l mod ule 2 10
15
20
20
5
15
30
30
Vehicle
OP-eration
No. Consume r
9 quattro Sport
10 Veh icle electrical sys tem control modu le 2
11 Vehicle electrical system control module
12 Terminal 30
Fuse p anel © (brown)
1 Luggage compartment lid control module, vehi­
cle electr ica l system control module
2 Right front seat heating
3
4
6
7
DCDC converter path 1
DCDC converter path 2
Right upper cab in heat ing
Electromechanical parking brake
8 Rear seat heating
9 Passenger side door control module
10 Left upper cabin heating
11 Passenger side door control module
F us e pa nel ® (red)
1 Rear center console outlet
2 Front center console outlet
3 Luggage compartment outlet
4 Cigarette lighter 6 Rear Seat Entertainment supply
7 Parking system
9 Electromechanical parking brake switch
10 Aud i side assist
Vehicle care Do-it-yourself service
Amps
35
30
20
5
30
15
40
40
30
30
30
30 30
15
15 15
15
15
5
7,5
5
5
iTechnical data

Emergency situations --------------=----Efffll
Emergency situations
General
This chapter is intended for trained emergency crew s and working
personnel who ha ve the necessar y tools and equipment to perform
the se operations . •
Starting by pushing or towing
(D Note
Vehicles with an automatic transmis sion cannot be started by
pushing or towing .•
Starting with jumper cables
If necess ary, the engine can be started by connecting it to
the battery of an other vehicle .
If the engine shou ld fai l to start because of a discharged or weak
battery, t he battery can be co nnecte d to the battery of
another
vehicle, using a pair of jumper cable s to start the engine .
Jumper cables
Use only jumper cables of suffic ient ly large cross section to carry the
sta rter cur ren t safely . Refe r to the manufacture r's specifications.
Use on ly j umper cab les with
insulated te rm ina l clamps w hich are
distinct ly marked :
plus(+) cable in most cases colo red red
minus (-) cable i n most cases colored black.
Safety first
& WARNING
Batterie s contain electricity, acid, and gas . Any of these can cause
very serious or fatal injury . Follow the inst ructions below for safe
handling of your vehicle 's battery .
• Always shield your eyes and avoid leaning over the battery
whenever possible.
• A discharged battery can freeze at temperatures just below
32 °F (0 °C). Before connecting a jumper cable, you must thaw the
frozen battery completely , otherwise it could explode.
• Do not allow battery acid to contact eyes or skin . Flush any
contacted area with water immediately .
• Improper use of a booster battery to start a vehicle may cause
an e xplosion.
• Vehicle batteries generate e xplos ive gases. Keep spa rks, flame
and lighted cigarettes away from batteries.
• Do not try to jump start any vehicle with a low acid level in the
battery.
• The voltage of the booster battery must also h ave a 12 -Volt
rating. The capacity (Ah) of the booster battery should not be
lower than that of the discharged battery. Use of batter ies of
different voltage or sub stantially different "Ah " rating may cau se
an explosion and personal injury.
• Never charge a frozen battery . Ga s trapped in the ice may cause
an e xplosion.
• Never charge or use a battery that has been frozen. The battery
case may have be weakened.
• Use of batteries of different voltage or substantially different
capacity (Ah ) rating may cause an explosion and injury . The
capacity (Ah ) of the booster battery should not be lower than that
of the discharged battery. _..
Vehicle care Do-it-yourself service Technical data

Emergency situations Ill
-------------=----
Connect POSITIVE (+) to POSITIVE (+) (red)
- Remove the cover above the jump start connectio n.
- Open the red cover o n the positive pole~
page 334,
fig. 248.
1 . Connect one e nd of the pos it ive cable ( red) on the
jump
start bolt~
page 334, fig. 249 (D (Bolts under red cover
= "positive") of the veh ic le to be started @.
2 . Connect the other end to the positive te rminal @ of the
booster ba ttery @.
Connect NEGATIVE(-) to NEGATIVE(-)
(black)
3. Con nect o ne end to the negative ter minal ® of the
boost er batte ry @ .
4. Connect the other end o f the nega tive cab le (black) to the
jump start bolt© (Bolts with hex head = "ne gative") of
the vehicle to be starte d @ .
Starting the engine
- Start the e ngine of t he ve hic le w ith the boos ter ba ttery.
Run the engine at a moderate speed.
- Start eng ine w it h discharged ve hicle bat tery in t he usu al
manner .
- If the engine fai ls to sta rt: do not k eep the s tarter
c ra nki ng for longer tha n 1 0 seco nds. Wait for a bou t
30 se conds and then t ry again.
- With engine ru nni ng, remove jumper cables from bot h
ve hicle s in th e exac t
re verse ord er.
- Close t he red cover on the pos it ive po le.
Safety first
T he battery is vented to the outside to prevent gases from enter ing
t he ve hicl e inter ior. Make su re tha t the ju mper clamps are we ll
connected with the ir
metal parts in full contact with the battery
terminals .
& WARNING
To avoid serious personal injury and damage to the vehicle, heed
all warnings and instructions of the jumper cable manufacturer . If
in doubt, call for road service .
• Jumper cables must be long enough so that the vehicles do not
touch.
• When connecting jumper cables , make sure that they cannot
get caught in any moving part s in the engine compartment .
• Do not bend over the batteries · danger of chemical burns!
• The battery cell locking screws mu st be tightened securely .
• Before you che ck anything in the engine compartment, always
read and heed all WARNINGS=>
page 272, ''Eng ine compart­
ment ".
0 Note
Imprope r hoo k-up o f jumpe r cab les can ruin the gene rator.
• Always connect POSITIVE( +) to POSITIVE(+), and NEGATIVE( -)
t o NEG ATI VE( -) ground pos t of the ba tte ry m anag er cont rol unit.
• Check that all sc rew p lugs on the battery cells are screwed in
fi rm ly . If no t, tig hten plugs prio r to con nectin g clamp on neg ative
battery terminal.
• P lease note that the proced ure for connecting a jumper cable as
described above app lies specifically to the case of your vehicle being
jum p st arted. When you a re giving a jump sta rt to anot her vehicle, do
not connect the negative( -) cab le to the negative (-) terminal on the
discharge d batte ry © =>
page 334, fig. 249 . Instea d, sec urely
connect the negative( -) cable to either a solid meta l component t hat
is f irm ly bolted to t he eng ine b lock or to the eng ine b lock itself. If the .,_
Vehicle care Do-it-yourself service Technical data

_____________________________________________ E_ m __ e_r-=g =- e_ n_c -==y "- s_i_ t _u _a _ t_ i_ o _ n_ s _ __.lfll
When it is no longer needed, unscrew the towing loop and put it back
into the vehicle toolkit. Be sure to have the towing loop stored in the
vehicle at all times.
& WARNING
If the towing loop is not screwed in as far as it will go, the thread
can pull out when the vehicle is towed -potential risk of an
accident. •
Rear towing loop
Do not install the rear towing loop until it is needed.
Fig. 252 Rear
bumper: Screwing in
towing loop
On the right side of the rear bumper there is a threaded hole
for the towing loop. The threaded hole is protected by a
cover.
- Remove the towing loop from the vehicle toolkit
=> page 318.
- Press the cover in by applying short strong pressure to the
bottom part to release it from the bumper :::::;, fig. 252.
- Screw the towing loop tightly into the threaded hole as far as it will go .
Vehicle OP-eration
Unscrew the towing loop again after use and install the cover in the
bumper. Install the cover in the bumper. Return the towing loop to
the toolkit . Be sure to have the towing loop stored in the vehicle at all
times.
& WARNING
If the towing loop is not screwed in as far as it will go, the thread
can pull out when the vehicle is towed -potential risk of an
accident. •
Loading the vehicle onto a flat bed truck
Front hook up
0 0
;
Fig. 253 Vehicle on
flat bed truck
- Align the vehicle with the centerline of the car carrier
ramp.
- Attach the winch hook to the front towline eye previously
installed.
Rear hook up
- Align the vehicle with the centerline of the car carrier
ramp.
Vehicle care Do-it-yourself service iTechnical data

_____________________________________________ E_ m_ e_r-= g ::.. e_ n_c-= y'- s_ i_t _u _a_ t_ i_ o _ n_ s __ _
& WARNING
• To reduce the risk of serious injury and vehicle damage.
-Always lift the vehicle only at the special workshop hoist and
floor jack lift points illustrated=>
page 338, fig. 254 and
=> page 338, fig. 255.
- Failure to lift the vehicle at these points could cause the
vehicle to tilt or fall from a lift if there is a change in vehicle
weight distribution and balance. This might happen, for
example, when heavy components such as the engine block or
transmission are removed .
• When removing heavy components like these, anchor vehicle
to hoist or add corresponding weights to maintain the center of
gravity. Otherwise , the vehicle might tilt or slip off the hoist ,
causing serious personal injury.
0 Note
• B e aw are of the following poi nts b efo re li fting the ve hicl e:
- The vehicle should never be lifted or jacked up from under­
neath the engine oil pan, the transmission housing , the front or
rear axle or the body side members . This could lead to serious
damage.
- To avoid damage to the underbody or chassis frame, a rubber
pad must be inserted between the floor jack and the lift points.
- Before driving over a workshop hoist, check that the vehicle
weight does not exceed the permissible lifting capacity of the hoist.
- Before driving over a workshop hoist, ensure that there is
sufficient clearance between the hoist and low parts of the
vehicle. •
Safety first Vehicle care Do-it-yourself service Technical data

________________________________________________ G_e_ n_e_ r _a_ l_i_n _f_ o_ r_m _ a_t_ i_ o _ n __ _
The safety compliance sticker
is your assurance that yo ur new vehicle complies with all applicable
Fede ral Motor Veh icle Safe ty Standards which were i n effect at the
time the vehicle was manufact ured . Yo u can fi nd this sticker on the
left doo r jamb.
It shows the mont h and year of prod uct io n and the
vehicle identification number of your veh icle (perforation) as well as
the Gross Vehicle Weight Rating (GV WR) and the Gross Axle Weight
Rating (GAWR).
The high voltage warning label
is located o n the loc k carrier.
The spark ignition system complies with the
Canadian standard ICES-002. •
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and the Gross Axle Weight
Rating (GAWR) for front and rear are listed on a sticker on the left
door jamb.
T he Gross Vehicle Weight Rating includes the weight of the basic
vehicle pl us f ull f uel tank, oil and coo la nt, plus max im um load, whi ch
includes passenger we ight (150 lbs/68 kg per des ignated seating
position) and luggage weight~& .
Gross Axle Weight Rating
The Gross Axle Weight Ra ting is the maximum lo ad that can be
applied at each axle of the vehicle~&.
Vehicle capacity weight
The vehicle capac ity weight (max . load) is listed either on the driver's
side B -pillar or inside the fuel fille r flap .
Safety first
& WARNING
• The actual Gross Axle Weight Rating at the front and rear axles
s hould not exceed the permis sible weights, and their combination
must not exceed the Gross Vehicle We ight Rating.
• Exceeding permi ssible weight rating s can result in vehicle
damage, accidents and personal injury .
0 Note
• The vehicle capac ity we ight figu res apply when the load is distrib­
uted evenly i n the vehicle (passengers and luggage). When trans ­
porti ng a heavy load i n the l uggage compartment, ca rry the load as
near to the rear axle as possible so that the veh icle's handling is not
impa ired.
• Do not exceed the maximum permiss ible axle loads o r the
maximum gross vehicle weig ht. Always remember that the vehicle's
hand ling will be affecte d by the extra load. Therefore, adjust your
speed a ccording ly .
• Always observe loca l reg ulations. •
Dimensions
The specifications refer to the basic mo de l. Differences may occur
depend ing on the model ty pe a nd options ordered, for exam ple, tir e
sizes .
0 Note
When d riving up steep ramps, on rough roads, over c urbs, etc . it is
impo rtan t to remember th at some parts of yo ur vehicl e, s uch as
spoilers or ex haust system components, may be close to the ground.
B e careful not to d amage them .•
Do-it,yourself service Technical data

______________________________________________ C _o_ n _ s_u_ m_ e_r_ I_n _f_ o_ r_m _ a_t_ i_ o _ n __ _
Consumer Information
Warranty coverages
Your Audi i s covered by the following warrantie s:
• New Vehicle Limited Warranty
• Limited Warranty Against Corrosion Perforation
• Emissions Control System Warranty
• Emissions Performance Warranty
• California Emissions Control Warranty (USA vehicles only)
• California Emissions Performance Warranty (USA vehicles only)
Detailed in forma tion reg ard ing yo ur war ran ties can be fo und in your
Warranty & Maintenance booklet .•
Operating your vehicle outside the
U.S.A. or Canada
Government regulations in the United States and Canada req uire that
au tomobile s mee t sp eci fic emi ssio n regula tions and safety s tan­
dards . Therefore, vehicles b uilt for the U .S .A . and Canada d if f er from
vehicles sold in othe r countr ies .
If you plan to take your veh icle outs ide the con tinen tal lim its of the
United States o r Canada , there is the poss ibility that
• unle ade d fu els for veh icles wi th c atal ytic conve rter m ay no t be
available;
• fue l may have a conside rably lowe r octane rat ing. Im proper f ue l
may cause engine damage;
• serv ice may be inadeq uate due to lack of proper service facilities,
too ls o r testing eq uipment;
• replacemen t parts may not be read ily avai lab le .
Safety first
• N aviga tion syst ems for ve hicles built fo r th e U .S.A . and Canada
will not necessar ily work in Europe, and may not work in other coun ­
tr ies o utside of North America.
0 Note
Audi c annot be responsible for me ch anic al d am age t hat cou ld re su lt
from inadequate fuel, service or parts ava ilability. •
Audi Service Repair Manuals and
Literature
Audi Off icial Factory Service Manuals and L iterature are published as
soo n as po ssib le a fter m ode l intr oduc tion. Serv ice Ma nuals and li ter ­
ature are avai lable to order from the Audi Tech nica l Lite rature
O rd er in g Center at:
www.audi.techliterature.com •
Maintenance
General
Your vehicle has been desi gned to help keep main tenance re quire­
ments to a minimum. Howeve r, a certa in amount of regular ma inte­
n ance is s till necess ary to assure your ve hicle's sa fety, eco nomy and
reliab ility . For deta iled ve hicle maintenance co nsu lt yo ur Warranty
&
Maint enance booklet .
Under difficult operating conditions, for example at ext reme ly low
outs ide temperatures, in very dusty regions, when towing a trai ler
very freque ntly, etc., some se rv ic e w ork s hou ld be perf ormed
between the intervals speci fied . T hi s applies particular ly to: .,_
Do-it,yourself service Technical data

______________________________________________ C _o_ n _ s_u_ m_ e_r_ I_n _f_ o_ r_m _ a_t_ i_ o _ n __ _
& WARNING (co ntinued )
• Always remove the ign ition key before anyone gets under the
vehicle.
• Alway s support your vehicle with safety stands if it is nece ssary
to work underneath the vehicle . The jack supplied with the veh icle
is not adequate fo r thi s purpose and could collap se causing
serious personal injury.
• If you must work underneath the vehicle with the wheels on
the ground, always make sure the vehicle is on level ground, that
the wheels are always securely blocked and that the engine cannot
be started.
• Always make sure the transmi ssion selector lever (automatic
transmi ssion) is in "P " (Park po sition ) and the park brake is firmly
applied.
<£> For the sake of the environment
• Changing the engine settings will adverse ly affect emission levels .
Thi s is det rimenta l to the environme nt and increases fue l co nsump­
tion.
• Always obse rve environmen tal regulat ions when d ispos ing of o ld
engine oil, used b rake fl uid, di rty e ngine coo lant, spent batter ies or
worn out t ires .
• Undeployed a irbag modules and pretensioners m igh t be classifie d
as Perchlorate Mater ia l -spec ial hand ling may apply, see
www.dtsc.ca.gov/hazardouswaste/pe rchlorate . When the vehicle or
parts of t he rest raint system includi ng ai rbag modu les safety belts
with pretens ioners are sc rapped, all applicable laws and regulat ions
m ust be ob served. Yo ur author ized Au di dealer is f amiliar wi th these
requirements and we recommend that you have your dealer perform
t his servi ce for yo u. •
Safety first
Additional accessories,
modifications and parts
replacement
Additional accessories and parts
replacement
Always co nsult an autho riz ed Audi d ealer bef ore
purchasing acces sories.
Yo ur vehicle incorporates the latest safety design feat ures ens uring a
high standard of active and pass ive safety .
Th is safety could be compromised by non-approved changes to the
veh icle . F o r th is reaso n, if p arts have to be rep la ce d , ple ase obse rve
the following points when installing addit ional accessories:
Approved Audi accessories and genuine Au di parts are available from
au thori zed Aud i dea le rs .
These dea lers a lso have the necessary facilities, tools and tra ined
specialists to i nstall t he pa rts and ac cesso ries p roperly.
& WARNING
Using the wrong spare parts or u sing non-approv ed accessories
c an cause damage to the vehicle and serious personal injury.
• Use only accessories expressly approved by Audi and genuine
Audi spare parts
• These parts and accessories have been specially designed to be
used on your vehicle.
• Never install accessories such as telephone cradles or beverage
holder s on airbag covers or within the airbag deployment zones .
Doing so will increase the risk of injury if airbags are triggered in
an a ccident!
• Before you check anything
in the engine compartment, always
read and heed all WARNINGS~
page 272. .,
Do-it,yourself service Technical data

_____________________________________________ C_o_ n_s _u_ m __ e_r _ I_ n_ f_o _r_ m_ a_ t_ i _o_ n __ __
FCC Part 15.19
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including inter­
ference that may cause undesired operation.
FCC Part 15.21
CAUTION:
Changes or modifications not express ly approved by the party
respons ible for compliance could void the user's authority to operate
the equipment .
RSS-Gen Issue 1
Operation is sub ject to the following two conditions:
( 1 ) this device may not cause interference, and
(2) this device must accept any interference, including interference
that may cause undesired operation of the device.•
Safety first Do-it,yourself service Technical data

___ A_ l_. p_ h _ a_b_ e_ t_ic _a_ l_ in_ d_e _ x ____________________________________________ _
A
A/C mode ...................... 93, 100
Accessories ..... .................. . 345
Active rollover protection system ... ... 186
Retracting rollover protection . ..... 187
Adaptive cruise control ............ .. 116
Chang ing speed .................. 119
Dr iver information ............... 122
Driver intervention prompt ........ 126
Driving in traffic ................. 117
Driving program .. .. ............. 127
Error messages . .. ...... .... ..... 125
Open road ...................... 117
Override ................ ...... .. 117
Request for driver to assume control 117
Save speed . . . . . . . . . . . . . . . . . . . . . . 119
Setting distance ................. 121
Setting time interval . ............. 121
Sett ings ... ..................... 127
Special driving situations ........ .. 127
Status messages ........ ......... 125
Switching on and off .............. 118
System limits ................ ... 127
T emporarily turning off ........... 120
warning/indicator lights ........... 123
Adaptive light ... ...... .............. 66
defect ive . . . . . . . . . . . . . . . . . . . . . . . . 3 7
Adding Engine coolant .................. 288
Engine oil .. ...... ....... ..... ... 284
Windshield washer flu id ........ ... 295 Additional accessories
............... 345 Side airbags .. .. .. .. .. .. ......... 218
Additives We
ight-sensing mat .............. 222
Engine oil ........ .... .. .. .. .. ... 284 When must
the system be inspected? 210
Adjusting All wheel drive
.. .. .. .. .. ...... ... .. 246
Steering column .......... .. .. .. . 105 Winter tires
.. .. ................. 311
Adjusting front seats .......... ...... . 77 Alloy wheels
........... .. .... .... .. 266
Airbag Warning/indicator lights ... .. .. .. .. 14
Airbag system .................. 199, 219
Advanced Airbag System .......... 203
Advanced Airbag System components 206 Care .................... .. .... . 213
Child restraints .................. 223
Children ........................ 222
Components (front airbags) ... .. .. . 206
Danger of fitting a child safety seat on the
front passenger seat ............ 201
Disposal ........ .... ..... .. .... . 213
Front airbags .............. .. 203, 204
How do the front airbags work? ..... 208
How many airbags does my vehicle have? .
206
How the Advanced Airbag System compo- nents work together ........... . 207
Important safety instructions on the knee airbag system ............ ... .. . 217
Important things to know .. .. .. .. . 199
Indicator light ........ .. .. .. .... . 210
Knee airbags .................... 215
Monitoring . .. ............... ... 210
PASSENGER AIR BAG OFF light ..... 211
Repairs .. ........ ... ... .. .. .. .. . 213
Safety instructions ............. .. 212 Alternator
Malfunct ion .... .. .. .............. 29
Anti-freeze
See Eng ine cooling system ......... 286
Anti-glare inside day-night mirror ..... .. 72
Anti -lock brake system
How the ABS system works . . . . . . . . 245
Wa rning/indicator lights . .......... 15
Anti-Slip Regulation System (ASR) How the system works ..... ... .. .. 242
Anti-theft systems Electronic immobilizer ............. 41
Ashtray ............................ 85
Asterisk What does it mean when something is
marked with an asterisk? . . . . . . . . . . . 5
Audi brak ing guard .................. 129
Error messages . . . . . . . . . . . . . . . . . . 131
Settings ........................ 131
Status messages ................. 131
Switching on and off ....... ... .. .. 131
Audi drive select Description ..................... 145
Setting the driving mode .......... 146
Audi Service Repair Manuals and Literature ..
343