automatic transmission AUDI A5 CABRIOLET 2014 User Guide

Hill descent control
Applies to vehicles: with multitronic/S tronic/tiptronic
The hill descent control system assists the
driver when driving down declines.
Hill descent control is activated when these­
lector lever is in D/S and you press the brake
pedal. The transmission automatically selects
a gear that is suitable for the incline . Hill de­
scent control tries to maintain the speed ach­
ieved at the time of braking, within physical
and techn ica l limitations. It may still be nec­
essary to adjust the speed with the brakes.
H ill descent control switches
off once the de­
cline levels out or you press the accelerator
pedal.
On vehicles w ith the cruise control system*
¢ page 83, hill descent control is also activat­
ed when the speed is set.
.&, WARNING
Hill descent control cannot overcome
physical limitations, so it may not be able
to maintain a constant speed under all
conditions. Always be ready to app ly the
brakes.
Manual shift program
App lies to vehicles: with multitronic/S tronic/tiptronic
Using the manual shift program you can
manually select gears.
F ig. 99 Center console: shifting t he gea rs manually
Transmission 89
Fig . 100 Stee ring whee l: Shift buttons*
Gear selection with selector lever
The tiptronic mode can be selected either with
the vehicle stat ionary or on the move .
.,. Push the se lector lever to the right from D/
5. An M appears in the instrument cluster
display as soon as the transmission has
shifted .
.,. To upshift, push the selector lever forward
to the plus position
0 ¢ fig. 99 .
.,. To downshift, push the lever to the minus
position
0 .
Gear selection with paddle levers*
The shift buttons are activated when these ­
l ector lever is in D/S or the tiptronic manual
shift program.
.,. To upshift, touch the button on the right
0
¢ fig. 100 .
.,. To downshift, touch the button on the left
0 .
.,. If you do not press a sh ift button within a
short time while in the D/S posit ion, the
transmission will return to automatic mode.
To keep shifting using the shift buttons,
move the selector lever to the right out of
the D/S position.
The transm ission automatically shifts up or
down before critical engine speed is reached .
The transmission only allows manual sh ifting
when the engine speed is within the permit­
ted range.
(D Tips
-When you shift into the next lower gear,
the transmission will downshift only

106 Audi drive select
Audi drive select
Driving settings
Introduction
App lies to vehicles: with Audi drive select
Drive select provides the possib ility to exper i­
e nce diffe ren t types of vehi cle sett ings in o ne
ve hicl e. For ins tance, us ing t he three
Com­
fort , Auto and Dynamic modes, the driver can
switch from a sporty to a comfortab le drivi ng
mode with the press of a b utton.
A ddit ionally, in veh icles wi th MM I*, the vehi ­
cle setup for
Individual* mode can be c us­
tom ized by you. This makes it possib le to
comb ine settings such as a sporty engine tun ­
ing with comfortable steering.
A WARNING
Improper use of the A udi drive select can
cause collisions , ot her acc idents and se ri­
ous pe rsonal injury.
Description
App lies to vehicles: with Audi drive select
The vehicle setup in each mode depends on
the veh icle's features . However, the engin e,
automa tic t ransmissio n and s teeri ng a re a l­
ways involved.
-
Engine and automatic transmission
Depending on the mode , the e ng ine and the
automatic t ransm ission respond quicke r or i n
a more ba la nced manne r to a cce le rator pedal
move ments. In t he sporty dynam ic mode, the
a ut om at ic t ra nsmissio n shifts at h igher R PMs.
Steering
The steering adapts in terms of stee ring effort
and steering ra tios . Ind irect steer ing that
moves easi ly, l ike the stee rin g in comfort
mode, is best su ite d t o long dr ive s on a high­
way. In co ntr ast, dynam ic mo de p rov ides
sporty, direct steering .
T he fo llow ing applies to vehicles with dynam ic
steer ing*: the stee ring ratio changes based on
ve hicl e spee d in order to maint ain op timum steering effort
for the drive r at all times . This
sets the stee ring to be less sens itive at higher
speeds in order to provide improved vehicle
control. At reduced speeds, however, steer ing
is more d irect in order to keep the steering ef­
fort as minima l as poss ible when the driver is
mane uveri ng the veh icle. At low and ave rage
speeds, dynamic steering addit iona lly pro­
vides more respon sive stee rin g pe rforma nce.
Adaptive dampers*
The adaptive dampers* use se nsors to record
informa tion regard ing steer ing movemen ts,
braking and acceleration o perations by the
drive r, road surfac e, d riv in g speed, and load.
T his makes it poss ible to adapt damp ing to
the driving si tua tion v irtu ally in real t ime.
Dr ive sele ct also makes i t possib le to sa tisfy
t h e desire fo r spo rty suspension ( Dynamic)
and comfortab le suspension (Comfort) with ­
o ut giving up ba lanced tuning (Auto) .
Sport differential*
As a component o f the all whee l dr ive sys tem
(quat tro)
~ page 184, t he spo rt differential *
dist ributes t he driving power to the rear ax le
depen ding on the sit uat io n. The distrib ution
of power var ies depending on the mode se­
lected. The goal is a high level of agility and
ability to accelerate on curves. T he ve hicle is
very res pons ive to stee ring .
Audi adaptive crui se control*
The behav ior when accelerating can be adjust­
ed from comf ortab le to sporty, depending on
t h e drive select mode. Adaptive cr uise control
also responds to the driv ing behavior of the
vehicle ahead in a mo re conservative o r spo rty
manner .
Engine sound*
The sound of the eng ine is adapted to these­
lected mode and ranges from subtle to sporty.
(!) Tips
- In s ome models, the maximum vehicle
spee d can only be reached in the
Auto
and Dynamic modes.

-For vehicles with an automatic transmis­
sion, selecting the
Dynamic mode re­
su lts in sporty shifting characteristics .
The
5 gear posit ion engages automati­
cally.
- In vehicles that have dynamic steering*,
operating noise is heard when starting or
stopping the eng ine. Th is does not indi­
cate a problem .
Selecting the driving mode
Applies to vehicles: with Audi drive select
You con choose between Comfort, Auto , Dy­
namic
and Individual* modes.
drive I I fi el•ct _ ~-=
Fig. 119 Center console ; Con trol for Aud i dr ive se lect
Fig. 120 MMI*: Aud i drive select
Adjusting the Individual mode
Applies to vehicles: with MMI and Aud i d rive select
Audi drive select 107
.. To set the mode, press the 1.:il'.'l button
r=> fig. 119 multiple times until the desired
mode is displayed in the instrument cluster .
Or
.. In the MMI*, select: ICARlfunction button>
Comfort, Auto , Dynamic or Individual* .
In vehicles without the MMI*, the ~:/~c1 button
is found underneath the shift/selecto r lever.
You can change the driving mode when the ve­
hicle is stationary or whi le driving.
If traffic
permits, after changing modes, briefly take
your foot off the accelerator pedal so that the
recently selected mode is a lso activated for
the engine and transmission.
Comfort -provides a comfort-oriented vehicle
setup and is suited for long drives on high­
ways.
Auto -provides an overall comfortable yet dy­
nam ic driving feel and is suited for every day
u se.
Dynamic -gives the driver a sporty driving
feel and is suited to a sporty driving style.
Individual* -~page 107.
& WARNING ~
Pay attention to traffic when operating
drive select to prevent potential risk of an
accident .
You con personally specify the vehicle setup in the MMI* .
.. Select the ICARI function button > Set indi­
vidual
control button. Once you select the
men u, you will automatically drive in the
in­
dividual
mode.
Systems Comfort
Engine/Transmission
balanced
Steering comfortable T
he equ ipment in your vehicle will determ ine
which settings you can adjust. The following
table provides an overview of the characteris­
tics of eac h driving mode.
Auto Dynamic
balanced spo
rty
balanced sporty

Emergency situations
General
This chapter is intended for trained emer­
gency crews and working personnel who have the necessary tools and equipment to
perform these operations.
Starting by pushing or
towing
(D Note
Vehicles with an automatic transmission
cannot be started by pushing or towing.
Starting with jumper
cables
If necessary, the engine can be started by
connecting it to the battery of another vehi­
cle.
If the engine should fail to start because of a
discharged or weak battery, the battery can be
connected to the battery of
another vehicle,
using a
pair of jumper cables to start the en­
gine.
Jumper cables
Use only jumper cables of sufficiently
largecross section to carry the starter current
safely. Refer to the manufacturer's specifica­
tions.
Use only jumper cables with
insulated termi­
nal clamps which are distinctly marked:
plus(+) cable in most cases colored red
minus(-) cable
in most cases colored black .
A WARNING
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal
injury. Follow the instructions below for
safe handling of your vehicle's battery.
- Always shield your eyes and avoid lean­
ing over the battery whenever possible.
Emergency situations 255
-A discharged battery can freeze at tem­
peratures just below 32 °F (0 °C). Before
connecting a jumper cable, you must
thaw the frozen battery completely, oth­
erwise it could explode.
- Do not allow battery acid to contact eyes
or skin . Flush any contacted area with
water immediately .
- Improper use of a booster battery to
start a vehicle may cause an explosion.
- Vehicle batteries generate explosive gas­
es. Keep sparks, flame and lighted ciga­
rettes away from batteries.
- Do not try to jump start any vehicle with
a low acid level in the battery.
- The voltage of the booster battery must
also have a 12-Volt rating. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged bat­
tery. Use of batteries of different voltage
or substantially different "Ah" rating
may cause an explosion and personal in­
jury.
- Never charge a frozen battery. Gas trap­
ped in the ice may cause an explosion.
- Never charge or use a battery that has
been frozen. The battery case may have
be weakened.
- Use of batteries of different voltage or
substantially different capacity (Ah) rat­
ing may cause an explosion and injury.
The ca pa city (Ah) of the booster battery
should not be lower than that of the dis­
charged battery.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS¢
page 206.
(D Note
- Applying a higher voltage booster bat­
tery will cause expensive damage to sen­
sitive electronic components, such as
control units, relays, radio, etc.
- There must be no electrical contact be­ tween the vehicles as otherwise current
could already start to flow as soon as the
positive(+) terminals are connected. ..,. •
•

256 Emergency situations
@ Tips
The discharged battery must be properly
connected to the vehicle's electrical sys­
tem. When jump starting or charging the
battery, never connect the negative
ground cable to the battery negative post
because the batte ry manager system must
be able to detect the battery 's state of
charge. Always connect the negative
ground cab le to the negative ground post
of the battery manager control unit.
Use of jumper cables
Make sure to connect the jumper cable
clamps in exactly the order described below!
Fig. 201 Engine compartment: Connectors fo r jum per
cables and charger
Fig. 202 Jump sta rting wi th the battery of anot her ve ·
h ide :@ booster battery, @ disc harged vehicle battery
The procedure described below for connecting
jumper cables is intended to provide a jump
start for your vehicle .
Vehicle with discharged battery:
.. Turn off lights and accessories, move lever
of automatic transmission to N (Neutral) or
P (Park) and set parking brake .
Connect POSITIVE(+) to POSITIVE(+)
(red)
.. Remove the cover above the jump start con­
nection .
.. Open the cover on the positive pole
¢fig. 201.
1. Connect one end of the red positive cable
on the
jump start bolt c::> fig. 202 @
(Bolts under cover= "positive") of the ve­
hicle to be started @.
2. Connect the other end to the positive ter-
minal @of the booster battery@.
Connect NEGATIVE (-) to NEGATIVE (-)
(black)
3. Connect one end of the b lack negative ca­
ble to the negative terminal @of the
booster battery @.
4. Connect the other end to the
jump start
bolt @
(Bolts with hex head= "negative")
of the vehicle to be started @.
Starting the engine
.. Start the engine of the vehicle with the
booster battery@. Run the engine at a
moderate speed.
.. Start engine with discharged vehicle battery
@ in the usual manner .
.. If the engine fails to start: do not keep the
starter cranking for longer than 10 seconds .
Wait for about 30 seconds and then try
again .
.. With eng ine running, remove jumper cables
from both vehicles in the exact
reverse or­
der .
.. Close the cover on the positive pole .
T he battery is vented to the outside to prevent
gases from entering the vehicle interior . Make
sure that the jumper clamps are well connect­
ed with their
metal parts in full contact with
the battery terminals.
A WARNING
--
To avoid serious personal injury and dam­
age to the veh icle, heed all warnings and
instructions of the jumper cable manufac-
turer . If in doubt, call for road service . ..,.

26 6 Con sum er Inf ormation
-Always make sure the transmission se­
lector lever (automatic transmiss ion) is
in "P" (Park position) and the park brake
is f irmly app lied .
@) For the sake of the environment
-Changing the engine settings wi ll ad­
versely affect em iss ion levels. This is det­
rimental to the environment and increas­
es fuel consumption .
- Always observe env ironmental regula­
tions when dispos ing of old engine oil,
used brake fluid, dirty engine coolant,
spent batteries or worn out tires.
- Undeployed airbag modules and preten­
s ioners might be classified as Perchlo ­
rate Material -spec ial handling may ap­
ply, see www.dtsc.ca .gov/hazardous­
waste/perch lorate . When the veh icle or
parts of the restraint system including
airbag modules safety belts wit h preten ­
sioners are scrapped, all applicable laws
and regulations must be observed. Your
authori zed Aud i dea ler is familiar with
these requirements and we recommend
that you have your dealer perform this
serv ice for you .
Additional accessories,
modifications and
parts replacement
Additional accessories and parts
replacement
Always consult an authorized Audi dealer be­
fore purchasing accessories.
Your veh icle incorporates the latest safety de­
sig n featu res ensu ring a high standard of ac­
tive and passive safety .
This safety could be compromised by non-ap­ proved changes to the veh icle. For this reason ,
if pa rts have to be replaced , please observe
the following points when install ing addition­
a l accessories: Approved Audi accessories and genuine Aud
i
parts are available from authorized A udi deal­
er.
T hese dea le rs a lso have the necessary facili­
ties, tools and trained specialists to install the parts and acc essories proper ly .
A WARNING
-Using the wrong spare parts or using non-
approved accessories can cause damage to
the veh icle and ser ious persona l injury.
- Use on ly accessories express ly approved
by Audi and gen uine Audi spare parts
- These parts and accessories have been
specia lly designed to be used on yo ur ve­
h icle .
- Never install accessor ies such as tele­
phone crad les or beverage ho lders on a ir­
bag covers or within the airbag deploy­
ment zones . Do ing so will increase the
risk of injury if a irbags are triggered in an
accident!
- Before you check anything in the engine
compa rtment, always read and heed a ll
WARNI NGS
9 page 206 .
(D Note
-If items other than genu ine Audi spare
parts, add-on equipment and accessory
items are used or if repair work is not
performed accord ing to specified meth­
ods, this c an resu lt in seve re damage to
your vehicle's eng ine and body (such as
corrosion) and adversely affect yo ur vehi ­
cle's warranty .
- If emergency repairs must be performed
elsewhere, have the vehicle examined by
an authorized A udi dealer as soon as
possible .
- The manufacturer cannot be held liable
for damage wh ich occ urs due to failure
to comply with these stipu lations.

276 Index .:..:..:..::....::..
...:..._ ___________________________ _
Monitoring the Advanced Airbag System 150
multitronic . . . . . . . . . . . . . . . . . . . . . . . . . 85
Automatic Shift Lock (ASL) . . . . . . . . . . . 86
Driving .... ............. .. .. .. .. .. 87
Emergency mode ......... .. .. .... .. 91
Manual shift program ............... 89
Selector lever . . . . . . . . . . . . . . . . . . . . . . 85
N
Natural leather
C leaning ... ................ ..... . 198
New tires and wheels ........... .. ... 233
NHTSA Contacting . ............. .. .. .. ... 129
Number of seats ............ ... .... . 132
0
Occupant seating positions .. .. .. .... . 122
Octane rating .. ........... ........ . 201
Odometer ... ................ ..... .. 12
OFF (automatic climate contro l) . . . . . . . . 70
Oil
refer to Engine oil . . . . . . . . . . . . 208, 211
Oi l consumption ............ ... .... . 211
On-Board Diagnostic System (OBD) Data Link Connector (DLC) .. .. .. .. .. . . 29
E lectronic speed limiter . . . . . . . . . . . . . . 29
Malfunction Indicator Lamp (MIL) . . . . . 29
Open door or front lid warning . . . . . . . . . 24
Opening Power windows .......... .. .. .... .. 39
Opening/clos ing
at the lock cylinder ......... ... .... .. 36
by remote contro l . . . . . . . . . . . . . . . . . . 34
with the central locking switch . ... .. .. 35
with the convenience key ... .. .. .... .. 35
Operate your vehicle econom ically and
minim ize po llution ......... .. .. .. .. . 189
Optional equipment Marked with an asterisk .... .. .. .. .. .. . 6
Other equipment (efficiency program) 27
Outside mirrors
refer to Exterior mir rors . . . . . . . . . . . . . 54
Outside temperature display ..... .. ....
24
Owner's manual
How the Owner 's Manual is organized ... 6
p
Paint damage ..... ................ . 197
Pa int No ... ... .. .. .. ...... ..... .. .. 261
Park assist . ..... .. ............. .... 109
Cleaning sensors/camera lenses .. .. .. 196
Parking .... .... .. ............. .... . 80
Automatic transmission ............. 87
Valet parking .... ................ .. 40
Parking brake . .. .. .. .. ...... ... .. .. . 79
also refer to Electromechanical parking
brake ... .. .. .. .. .. ........... .. .. . 79
Parking system .. .. ................ . 109
Rear .... ... .. .. .. ...... ....... .. 109
Rear , with rear view camera .. .... .. .. 111
Parking system (rear) . ........... .. .. 109
Adjusting the warning tones ....... .. 110
Parking system (rear , with rear view cam-
era) Parking mode 1 .. ............. .... 113
Parking mode 2 .. ... .......... .. .. 114
Safety precautions ............. .... 111
Switching on/off . ................ . 112
Switching rear view camera on/off .. .. 115
Parts replacement ................. . 266
PASSENGER AIR BAG OFF light .... .... 151
Passive safety system . ... ..... ... .. .. 121
Pedals ............................ 126
Physical principles of a frontal co llision 133
Plastic parts Cleaning .. .. .. .. ............. .. .. 197
Polishing ... .... .. ................ . 197
Pollutant filter (automat ic AC system) .. . 69
Power seat adjustment .. ... .......... .. .. . 61
Power locking system ................ . 31
Emergency locking ................ .. 36
Power windows . ................. .. 40
Rear lid ... .... .. ............. .... . 37
Selective unlock feature . . . . . . . . . . . . . 36
Settings .. .... .. ............. .... . 36
Power steering
refer to Electro-mechanical power as-
sist 184

------------------------------~I~ n~ d~ e~x~ 279
START ENGINE STOP button (Convenience
key) ...... .. .. ................ ..... 77
Starting from rest . . . . . . . . . . . . . . . . . . . . 80
Starting off with a trailer .... .. .. .. .. .. 81
Starting the engine . . . . . . . . . . . . . . 74, 77
Steer ing
Lacking the steer ing . . . . . . . . . . . . . . . . 7 4
also refer to Electro-mechanical power
assist . .. .. .... ............. .. .. . 184
Steering wheel Adjust ing steering column . .. .. .. .. .. 74
Indicator light . . . . . . . . . . . . . . . . 18, 184
Steps for determining correct load limit . 231
Stopping the engine . . . . . . . . . . . . . . 76, 78
Storage . .. ... ...... ............. ... 65
S tronic ..... .. ................ ..... 85
Selector lever . . . . . . . . . . . . . . . . . . . . . . 85
S tronic transmission
Emergency release .................. 91
L aunch Contro l Program ............. 90
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Symbols
refer to Warning/indicator lights .. .. .. 13
T
Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . 11
Ta il lights
C leaning ... .... ........... .. .. .. .
Technical mod ifications
Textiles 196
267
C leaning ... .. ............. .. .. ... 198
The first 1,000 miles (1,500 km) and after-
wards ..... .. .. ................ .... 187
Tie-downs . . . . . . . . . . . . . . . . . . . . . 67, 128
tiptronic . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Automatic Shift Lock (ASL) . . . . . . . . . . . 86
Driving ... . .... ............. .. .. .. 87
Emergency mode ... ...... .. .. .. .. .. 91
Manual shift program . . . . . . . . . . . . . . . 89
Selector lever . . . . . . . . . . . . . . . . . . . . . . 85
Tire pressure .............. .... .. ... 228
T ire pressure monitoring system
L oss of air pressu re ................ 241
Malfunction ................ ... ... 241
Resetting tire pressures ....... ... .. . 242 T
ires .............................. 222
Low aspect ratio tires .............. . 239
Serv ice life . ... .. .. ............... 232
Speed rating letter code ............ 234
Tire manufacturing date ............ 234
Tire pressure monitoring system ..... 240
Tire specifications .. . .... .. .... .... 234
Tread depth ...... ...... .......... 232
Uniform tire quality grading ..... .. .. 236
Winter tires . .. .. .... ........... .. 237
Tires and vehicle load limits ........... 230
Tires and wheels Checking tire pressure ............. .
Cold tire inflation pressure ...... .. . .
Dimensions
. . .. .. .................
General notes .. .. .. ... ....... .... .
Glossary of tire and loading terminolo-
gy .......... ... .. .............. .
New tires and wheels ........... .. . .
Replacing ..... ...... ............ .
Snow cha ins . .. .. .. . ............. .
Tires and vehicle load limits ........ .
Wheel bolts
Winter tires
T ire service life
Tool kit
..... .. ...............
Torn or frayed safety belts
Towing 228
226
233
222
223
233
234
238
230
239
237
232
243
135
Front eyelet ... .. .... ............. 258
Rear eyelet .. .. .. ................. 258
Tow truck procedures .............. . 257
TPMS Tire pressure monitoring system ..... 241
Trailer towing ... .. ................. 192
Operating instructions .......... .... 192
Technical requirements . . . . . . . . 192, 193
Tips ......... ... .. ..... .......... 194
Transmission . ... .. .. ................ 85
Transmission malfunction (in dicato r light) 91
Transport Canada .. ................. 129
Travel mode . . . . . . . . . . . . . . . . . . . . . . . . 53
Tread Wear Indicator (TWI) ........... 232
Trip computer Fuel consumption . . . . . . . . . . . . . . . . . . 25
Mileage ... .. .. .. .. . .. .... ........ . 25
Single-trip memory ................. 25
Total-trip memory ..... ....... .... .. 25
•
•