ECO mode AUDI A5 CABRIOLET 2015 Owner's Manual

Child safety
control unit of the Advanced Airbag System .
When a chi ld restraint is being used on the front
passenger seat with a typical 1 year-o ld chi ld, the
Advanced Airbag System compares the weight measured by the weight sensing mat with the in­
formation stored in the electron ic control unit .
The electronic control unit a lso registers the ten ­
sion on the front passenger safety be lt. The ten ­
sion on the safety belt for the front passenger
seat will be d ifferent for an adult w ho is properly
using the safety belt as compared to the tens ion
on the belt when it is used to attach a child re­
s traint to the seat. The senso r below the latch fo r
t he sa fety belt for the fron t se at passenge r
meas ures the tension on the be lt . T he inp ut from
this sensor is then used with the weight to "de­
cide", whether there is a c hild restraint with a
typical 1 year -old chi ld on the front passenger
seat and whether or not the airbag must be
t urned off .
Child restraints and Advanced Airbags
Regardless of the child restraint that you use,
make sure that it has been ce rtified to meet Un it­
ed States Fede ral Motor Vehicle Safety Standards
and h as been ce rtified by its manufac turer for
use w ith an airbag . A lways be sure tha t the child
restraint is p roperly ins talled at one of the rear
seating positions . If i n exceptiona l circumstances
you must use it on the front passenger seat, care­ fully read all of the informat ion on child safety
and Advanced Airbags and heed all of the appli­
cable WARNINGS . Make certain that the ch ild re ­
straint is correctly recognized by the weight-sens­
ing mat inside the front passenger seat, that the
front passenge r airbag is t urned
off and t hat the
air bag s tatus is a lways cor re ctly s ignaled by the
PASSENGER AIR BAG OFF li ght .
M any types and models of child restra ints have
been ava ilable ove r the yea rs, new models a re in­
t roduced regu larly incorporat ing new and im ­
p rove d des igns and o lder models are taken out o f
prod uction. Child restraints are not standardized .
Ch ild restrai nts of the same type typically have
d ifferent weights and s izes and different 'foot ­
prints,' the si ze and shape of the bottom of the
chi ld restraint that sits on the seat, w hen they
154 are
insta lled on a vehicle seat. These differences
make it virtua lly impossib le to certify compliance
with the requirements for advanced airbags with
each and every chi ld restraint that has ever been
sold in the past or will be sold over the course of
the usefu l life of your vehicle.
Fo r th is reason, the United States National High ­
way Traffic Safety Adm inistrat ion has published a
li st of specific type, makes and models of child
restraints that must be used to cert ify compli ­
ance of the Advanced Airbag System in your veh i­
cle w ith the s uppression requirem ents of Federal
Motor Veh icle Safety S tanda rd 208. These child
rest rain ts are:
Subpart A -Car bed child restra ints
Model Manufactured on or
after
Angel Guar d Angel Septe mber 2S, 200 7
Ride AA 2403FO F
Subpart B - Rear-facing child restraints
Model Manufactured on or
after
Century Smart Fit 4 S4 3 December 1, 1999
Cosco Arriva September 2S, 2007
22-013PAW and bas e
22-999WHO
E venflo Discove ry Ad -December 1, 1999
just R ight 212
E ven flo Firs t Choi ce De cembe r 1, 1999
2 04
Graco Infant 84S7 December 1, 1999
Graco Sn ug ride Se
ptember 2S, 2 007
Peg Perego Pr imo Viag- September 2S, 2007
gio SIP I MUNOOUS
Subpart C -Forward-facing and convertible
child restraints
Model Manufactured on or
after
B ritax Round about September 2S, 200 7
E 9 L0 2xx
Cosco Tou riva 02Sl9 December 1, 1999

M N
ci u.. co ,...., \!) 1.1'1
N 1.1'1 ,....,
on necessary precautions e.g. corrosion preven­
tion, maintenance and storage. Pay attention to
addit ional information concern ing the battery.
Refer to
c> page 204.
Economical and environ­
mentally-friendly driving
General
Your personal style of driving will determine the
economy of your vehicle, as well as exhaust and
noise levels.
Fu el economy, environmental impact , and wear
on your engine, brakes and tires largely depend
on three factors:
- your persona l dr iving style
- operating conditions
- technical limitations
If you anticipate what you need to do next and
drive economically, you can easily cut your fuel
consumption by 10-15 percen t. This sec tion will
give you some tips on how you can help the envi ­
ronment and your pocketbook .
(!) Tips
The consumpt ion estimates as published by
ENVIRONMENTAL PROTECTION AGENCY (EPA)
and Transport Canada may not correspond to
your actual consumption on the road, which
w ill vary depending upon vehicle load and
speed, road and weather conditions, trip
length, etc.
Drive smoothly and keep a lookout ahead
Vehicles use the most fuel when they are acceler­
ating.
" Avoid unnecessary accelerating and braking.
Vehicles use the most fuel when they are acceler ­
ating . If you anticipate what is going to happen
next, you will need to brake less and, thus, accel­
e rate less. Let the vehicle coast whenever possi­
ble - for example when yo u see that the next traf­
fic light is red .
Driving and the environment
Avoid full throttle
Driving at moderate speeds saves fuel and im­
proves your mileage .
"Try and keep well below your car's maximum
speed.
Acce lerat ing gently reduces fue l consumption,
engine wear, and does not disturb the environ­
ment .
Fuel consumption, exhaust emissions and engine
noise increase disproportionately at high speeds.
If you drive at approximate ly three quarters of
top speed, fuel consump tion will be reduced by
one half. Never drive faster than the posted
speed l imit and weather cond itions permit .
Reducing unnecessary idling
Even when your car is jus t idling it burns up fuel.
" Shut the eng ine off when you are not driving
the vehicle.
" Do not warm up the vehicle by lett ing the en-
gine run at idle.
It makes sense to shut off the engine in traffic
jams, when wa iting for tra ins to pass a t railroad
crossings, or at traffic lights that have long waits
on red . Turning the engine
off for just 30-40 sec ­
onds saves more fue l than is burned starting the
. . engine again.
It takes a long t ime for the engine to warm up
fully when it is running at idle. However, wear
and noxious emissions are especially high when
the engine is warming up. So you should drive
away as soon as you sta rt the engine and avoid
running at high rpms wh ile the engine is st ill
warming up.
(D Note
Do not leave engine idling unatt ended afte r
starting .
If warning lights should come on to
indicate improper operation, they would go
un heeded . Extended idling also produces
heat, which could result in overheating or oth­
er damage to the vehicle or other property.
179

M N
ci u.. co ,...., \!) ..,.,
N ..,., ,....,
Trailer mode Driving with a trailer
General information
Your Audi was designed primarily for passenger
transportation.
If you plan to tow a tra iler, p lease remember that
the additiona l load will affect durability, econo­
my and performance .
T railer towing not on ly places more stress on the
vehicle, it also calls for more concentrat ion from
the driver .
F or this reason, a lways fo llow the operating and
d riving instructions provided and use common
sense.
Technical requirements
Traile r hitch
Use a weight-carrying hitch conforming to the
gross trailer weight. The hitch must be suitable
for your vehicle and trailer and must be mounted
securely on the veh icle 's chassis at a technically
sound
location . Use on ly a tra iler hitc h with a re­
movable ba ll mou nt. Always chec k w ith the t ra il­
e r hitch m anu fac tur er to make sure that you a re
using the co rrec t hitch.
Do not use a bumper hitch .
The hitch must be installed in such a way that it
does not in terfere with the impact-absorbi ng
bumper system. No mod ificat ions should b e
mad e to the vehicle exhaust and brake systems .
Fr om time to t ime, c hec k t hat a ll h itch mou nti ng
bo lts remain sec urely fastened .
When you are no t tow ing a trailer,
remove the
trai ler hitch ball mount . Th is prevents the hitc h
fr om caus ing damage should you r vehicle be
s truck from behind¢,&. .
Trailer brakes
If yo ur tra iler is equipped w it h a braking system,
check to be s ure that it conforms to all regu la­
tions.
Trailer mode
T he trailer hyd raulic brake system must not be di ­
rect ly connected to the ve hicle's hydraulic b rake
system ¢.&. .
Safety chains
Alw ays use s afety ch ains be tween your ve hicle
and t he tra ile r.
Trailer lights
Tra ile r li ghts must meet all regulations. Be sure
to check w it h your author ized Audi deal er for cor­
r e ct w iring, sw itches, and relays.
Mirrors
If you are unable to see the traffic behind you us­
i ng the regular o uts ide mirrors, then you
must in ­
sta ll extended mirrors .
It is importa nt that you
always have clea r vision to the rea r.
_&. WARNING
- I f a trai ler has elec trical brake s please note
th at these b ra kes are not acti va ted by the
factory -fitted contro l unit -ris k of acci dent!
- After removing the t railer hi tch, do n ot store
it in your vehicle . In case o f su dden braking,
the hi tch could fly forward and injure you or
your passe ngers.
Operating instructions
Maximum traile r weight
A trai ler for you r vehicle is limited to a typical
class 1 or class 2 trailer.
Trailer load distribution
B e sure the load in the t ra iler i s held secure ly in
pla ce to prevent it from sh ifting forw ard , back ­
war d or sideways .
Never allow a passenger to ride in a trailer¢.&.
in Driving in struc tion s on page 182.
Engine cooling system
Towing a trailer makes the engine work harder . It
is important that the cooling system's pe rform­
ance is up to the additional load . Ma ke s ure that
t h e coo ling system has enoug h fluid.
IIJJ,
181

M N
ci u.. co ,...., \!) ..,.,
N ..,., ,....,
Trailer mode notes
Important to know
Your vehicle hand les differently when tow ing a
trailer because of the additional weight and dif­
ferent weight distribution. Safety, performance
and economy will greatly depend on how careful­
ly you load your trailer and operate your rig.
Before you actually tow your trailer, practice
turning, stopping and backing up in an area away
from traffic. Keep practicing until you have be­
come completely familiar with the way your vehi­
cle-trailer combination behaves and responds.
Backing up is difficult and requires practice. Back­
ing up with a trailer generally requires steering
action opposite to that when backing up your ve­
hicle without a trailer .
Maintain a greater distance between your vehicle
and the one in front of you. You wi ll need more
room to stop. To compensate for the trailer, you
will need a larger than normal turning radius.
When passing, remember that you cannot acce l­
erate as fast as you normally would because of
the added load. Make sure you have enough room
to pass. After passing, allow plenty of room for
your trailer before changing lanes again.
Avoid jerky starts, sharp turns or rapid lane
changes.
(D Tips
- Do not tow a trailer during the break-in peri­
od of your vehicle.
- If you tow a trailer, your A udi may require
more frequent maintenance due to the ex­
tra load
¢ page 248 .
Parking on a slope
Do not park on a slope with a trailer. If it cannot
be avoided, do so only after doing the following:
When parking:
.. Apply the foot brake.
.. Have someone place chocks under both the ve­
hicle and the trailer wheels.
Trailer mode
.. With chocks in place, slowly release the brakes
until the wheel chocks absorb the load.
.. Turn the whee ls towards the curb .
.. App ly the parking brake.
.. Move the selector lever to P.
When restarting after parking:
.. App ly the foot brake.
.. Start the engine.
.. Move the selector lever to D/S .
.. Release the parking brake and slowly pull out
and away from the wheel chocks.
.. Stop and have someone retrieve the wheel
chocks .
(D Tips
If you move the selector lever of the automat­
ic transmission to P before applying the park­
in g brake and before blocking the wheels, you
may have to use more force later to move the
l ever out of the P position.
183

M N
ci u.. co ,...., \!) 1.1"1
N 1.1"1 ,....,
specially conditio ned water an d the manu fa ctu r­
er's glycol-basedcoolant additive Gl3 antifreeze
with anticorrosion additives (50% for USA mod­
els; 60% for Canadian models). This m ixture both
assures the necessary frost protection and pro­
tects meta l components in the engine's cooling
system from corrosion and scal ing . It also raises
the boiling point of the coolant.
Do not reduce the concentration of the coolant in
the summer by adding plain water .
The p ropor­
tion of coolant addit ive must be at l east 50 %
but n ot mor e th an 60 %
to maintain antifreeze
protection and cooling efficiency. If the coolant
frost protection is too low, the coolant cou ld
freeze and damage the vehicle heating and en­
gine cooling system.
F or yea r-round driving, antifreeze is added at the
factory fo r temperatures dow n to:
- -31°F(-35°C)USA
- -40 °F ( - 40 °C) Canada.
If you must add coo lant, use a mixture of water
and coolant addit ive. Mixing the coolant additive
with distilled water is recommended.
A WARNING
Before you check anything in the engine com­
partment, always read and heed all WARN­
INGS
¢ &. in Working in the engine compart­
ment on page 195.
(D Note
- Before winter sets in, have the coolant
checked to see if the coolant addit ive in your
vehicle is suffic ient to meet the cli mate con­
dit ions. This is especially important if you
li ve in a region where the win ter is extreme­
l y co ld. If ne cessary, i ncrease the proport ion
of coo lant add itive to 60%.
- When adding coolant a ddit ive to you r cool ­
i ng system, remember:
- We recommend using only coolant addi­
tive Gl2++ or Gl3 for your ve hicle. This
coolant additive is ava ilable at authorized
Audi dea lers. Other types of ant ifreeze can
significant ly reduce co rrosion protection.
Checking and Fillin g
The resulting corrosion can ca use a loss o f
coolant and serious engine damage.
- Do not add any type of rad iator le ak sealan t
to your vehicle's engine coolant. Adding ra­
diator repai r fluid may adverse ly affect the
function and performance of your cooling
system and could result in damage not cov­
ered by your New Vehicle Lim ited Warranty.
Checking the engine coolant level
The engine coolant level can be checked with a
quick glance.
Fi g. 175 Engine compartment: Cover on the coolant ex­
pa nsion tank
.. Before you check anything in the engine com­
partment,
alwa ys re ad and heed all WARN­
INGS ¢ A in Working in the engine compart­
ment on page 195.
.. Park your vehicle on a level su rface.
.. Tu rn off the ignition .
.. Read the engine coolant level from the coolant
expansion tank
¢fig . 175, ¢page 197,
fig . 172 .
With a cold engine, the coolant leve l
should be between the "M IN" and "MAX" mark­
ings. When the eng ine is warm, the level may
be slightly above the "MAX" marking.
The location of the coo lant expansion tank can be
seen in the engine compartment illustration
¢page 197.
To obtain an a ccur ate reading, the engine m ust
be switched off.
T he expansion tank in yo ur veh icle is eq uipped
with an electric coo lant level senso r.
When the coolant leve l is too low, the wa rn ing
light in the Auto-Check System¢
page 17 will
201

Checking and F ill in g
The brake fluid reservoir is located at the rear
partition of the engine compartment on t he left
side ¢
page 197.
The fl uid level may drop slightly after some time
due to the automatic adjustment of the brake
pads. This is not cause for alarm.
If the b ra ke fluid level fal ls considerably below
the "MIN" mark, the brake warn ing/indi cator
light (U.S. models:
1111 , Canadian models: . )
will come on ¢
page 15. Do not contin ue to oper­
ate the vehicle . The complete brake system
should be thoroughly checked by an author iz ed
Aud i dealer or qualified workshop and the cause
corrected . If the brake fluid level is too low, the
brake warning/ind icator light w ill illuminate .
Contact an authorized Audi dealer
i mmed iately .
{D) Tips
The brake fluid reservoir is located under­
neath the cove r.
Changing brake fluid
Have the brake fluid changed by an experienced
technician .
Brake fluid absorbs moist ure from the a ir. If the
water content in the brake fluid is too high, cor­ rosion in the brake system may result after a peri­
od of time . The boiling point of the brake flu id
w ill also decrease conside rably and dec rease
b rak ing perfo rmance.
Therefore, the brake flu id must be changed
e ve ry
two year s.
Always use new brake fluid w hich con­
forms to Fede ral Motor Vehicle Standard "FMVSS
1 16 DOT 4".
The brake fluid rese rvoir can be difficult to reach,
therefo re , we recommend that you have the
b rake fluid changed by your author ized
Audi
dealer .
Your dealer has the correct too ls , the
right brake fluid and the know-how to do t his for
you.
A WARNING
- B rake fluid is poisonous. It must be stored
on ly in the closed original container out of
the reach of children!
204
- Brake fail ure can resu lt from o ld or inappro­
priate brake fluid. Observe these precau ­
tions:
- Use only b rake fluid that meets SAE spec i­
f ica tion
J 170 3 and conform s to Federa l
Motor Vehicle Standard 116. Always check
with yo ur autho rized Audi dea le r to make
su re you are using the correct brake fl uid.
The correct type of brake flu id is also ind i­
cated on the brake fluid reservoir.
- The brake fl uid must be new. Heavy use of
the brakes can cause a vapor lock if the
brake f luid is left in the system too long.
This can seriously affect the efficiency of
the brakes as well as your safety. This
could result in an acc ident.
(D Note
Brake fluid will damage the paint of your vehi­
cle.
@ For the sake of the env ironment
Because of the prob lem of prope r disposal of
brake fluid as well as the special tools re­
qu ired and the necessary expert ise, we rec­
omme nd that you have the brake flu id
changed by you r autho rized Aud i dea le r.
Battery
, General information
U nder normal operating conditions, the battery
i n your Audi does not need any maintenance.
Wi th
high outside temperatures or long daily
drives we recommend that you have the e lectro ­
lyte level checked by an a uth orized Aud i deale r o r
qualified workshop . The electrolyte leve l should
a lso be checked each time the batte ry is c ha rged
~ page 206.
Have the battery checked when yo u take your ve­
hicle in for service . You a re well adv ised to re­
pla ce a battery that is older tha n 5 years.
With certain types of airbag deployment, the bat ­
te ry is disconnected from the veh icle elect rical
system for safety reasons
¢ & in Repair, care
and disposal of the airbags on page 1 45.

Wheels
Occupant loading and distri­
bution for veh icle normal load
for various designated seat ing
capacit ies
Refer to the tire inflation pressure
label
c:> page 219, fig . 182 for
the number of seating positions .
Refer to the table
c:> page 220 for
the number of people that corre­
spond to the vehicle normal load .
New tires or wheels
Audi recommends having all work
on tires or wheels performed by
an authorized Audi dealer or au­
thorized repair facility. These fa­
cilities have the proper knowledge
and are equipped with the re­
quired tools and replacement
parts .
.,.N ew tires do no t yet have the
optimum adhesion properties.
D rive carefu lly and at moderate
speeds fo r the first 350 miles
(500 km) with new tires.
.,. Use tires of the same construc­
tion, size (rolling circumference)
and as close to the same tread
pattern as possib le on all four
wheels.
.,. Do not replace tires individually.
At least replace both tires on the same axle at the same time .
216
.,.A udi recommends that yo u use
Aud i O rig ina l equipment tires . If
you would like to use different t ir es, please note that the ti res
may pe rform differently even if
they are the same size
c:> A -
.,. If you would li ke to equ ip your
vehicle with a tire/rim combina ­
t ion tha t is different from what
was installed at the facto ry, con­
sult with an authorized Audi
dea ler or authorized repa ir facili­
ty before making a purchase
¢ ,&. .
The spare tire* is different from
the regular tires installed on the
vehic le - for examp le, if winter
tires or wide t ires are insta lled -
then only use the spare tire* tem­
porarily in case of eme rgency and
drive carefully wh ile it is in use. It
s h o ul d be rep laced wi th a regular
tire as soon as poss ib le .
On
all wheel drive vehic les, all
four wheels must be equipped
with tires that are the same brand
and have the same construction
and tread pattern so that the
dr ive system is not damaged by
diffe rent tire speeds. For this rea­
son, in case of emergency, only
use a spa re tire* that is the same
circumference as the regular tires . .,.

M N
ci u.. co ,...., \!) ..,.,
N ..,., ,....,
damage the t ires, and the c hains will quickly be
destroye d.
A WARNING
Using inco rrect snow cha ins or installing snow
chains incorrectly can resu lt i n loss of vehicle
cont ro l, whic h increases the r isk of an acci ­
de nt.
(D Note
Snow chains can dama ge the r ims/whee l cov­
ers * if th e cha ins come into d irect contact
w it h them. Remove the whee l cov ers* f irst .
Use coat ed snow c hains.
Low aspect ratio tires
Your Au di is factory -equip ped wi th low as pect ra ­
tio ti res. T hese ti res have bee n thoroughly teste d
a nd been se le cted specific ally fo r your model fo r
t he ir su perb pe rformance, road feel and handling
u nd er a variety o f driving conditions . Ask yo ur au­
thor ized A udi dealer for mo re deta ils.
The low aspe ct r atio of these ti res i s indic ated by
a numer al of
55 or les s in th e tire's si ze des igna ­
tion. The nu mera l represen ts the ra ti o of the
tire's sidewall he ight in relation to its trea d width
e x pressed in percentage. Convent io na l tires have
a he ight/w idth ratio of 60 or mo re.
The performance of low-aspect-ratio tires is par­
ticularly sensitive to improper inflation pres­
sure . It is therefore important that low aspect
ratio tires are inflated to the specified pressure
and that the inflation pressure is regularly
checked and maintained . Tire pressures should
be checked at least once a month and always
before a long trip
¢ pag e 219.
What you can do to avoid tire and rim
damage
L ow aspec t rat io t ires ca n be damaged more easi­
l y by impact wi th pot ho les, curbs, gulli es or
r idges on the road, par ticularly if the tire is un­
de rin fla ted.
In o rder to m inim ize the occu rrence o f impact
damage to the t ires of your v ehicl e, we recom-
Wheels
me nd that yo u observe the follow ing p recau ­
t ions:
- Alw ays m aintain r eco m me nded infl ation pre s­
sures. C heck your tire pressure every 2,000
m iles (3,00 0 km) an d ad d air if necessary .
- Dr ive c arefully on road s wi th pot holes, deep
gu llies o r ridges. The impac t from dr iv ing
through or over s uch obstacles can damage
your tires . Impact with a curb may a lso ca use
damage to your tires .
- After a ny impact, imme diate ly inspect yo ur
tires o r have them inspected by the nearest au­
thorized A udi dealer. Rep lace a damaged t ire as
soon as possible.
- Inspect your tires every 2,000 m iles (3,000 km)
for damage and wear . Damage is not always
easy to see. Damage can lead to loss of air and
unde rinflation, w hich could even tually cause
t ire failure .
If you beli eve that a t ire may have
been damaged, re place the t ire as soon as pos­
s ible.
- These ti res may wear more quickly tha n oth ers .
- Please also remember that, wh ile these tires
delive r responsiv e han dling, they may r ide less
comfortably and make mo re no ise than other
c h o ic e s.
Reduced performance in winter/cold season
conditions
All t ir e s ar e designed for certa in purpos es. T he
l ow asp ect ra tio, ultr a hig h perfor man ce tire s
o rigi nall y insta lled on y our veh icle are in tende d
f or m aximum dry an d we t road pe rformance and
handli ng. They are not suitab le for co ld , snowy or
icy weather conditions . If you dr ive under those
c ircumstances , you sho uld eq uip your vehicle
with all-season or winter tires, which offer better
t raction unde r those co ndit io ns. We suggest you
u se the recommended snow or all-seaso n tires
spec ified for your veh icle, o r the ir equiva le nt.
Refer to¢
page 224 for more detailed informa ­
t ion regarding w inte r tir es.
Uniform tire quality grading
- Tread wea r
- Traction AA AB C
- Temperature AB C
225

M N
ci u.. co ,...., \!) 1.1'1
N 1.1'1 ,....,
Fuse panel© (brown)
No. Consumer
1 Luggage compartment lid control module
(allroad)
2 12-volt socket, cigarette lighter
3 DCDC converter path 1
4 DCDC converter path 2, sound amplifie r,
rad io
6 Right upper cabin heating (Cabriolet)
7 Electromechanical parking brake
9
Right front door (window regulator, cen-
tral locking, mirror, switch, lighting)
10 Left upper cabin
heating (Cabriolet)
Two-door models: rear right w indow regu-
11 lator; Four-door models: rear
right door
(window regulator, central locking, switch,
lighting)
12 Cell phone prep
Fuse
panel © (black)
No. Consumer
1 Right front seat heating
4 MMI
5 Radio
6 Rear view camera
7 Rear window heater (allroad)
8 Rear
Seat Entertainment
Bulbs
Replacing bulbs
For your safety, we recommend that you have
your authorized Audi dealer replace any bulbs for
you .
It is becoming increasingly more and more diffi­
cult to replace vehicle light bulbs since in many
cases , other parts of the car must first be re­
moved before you are ab le to get to the bulb .
This applies especially to the light bulbs in the
front of you r ca r which you can only reach
through the engine compartment .
Sheet metal and bulb holders can have sharp
edges that can cause ser ious cuts, parts must be
Fuses and bulbs
correct ly taken apart and then properly put back
together to help prevent breakage of parts and
long term damage from water that can enter
housings that have not been properly resealed.
For your safety, we recommend that you have
your authorized Audi dea ler replace any bulbs for
you, since your dealer has the proper tools, the
correct bulbs and the expertise.
Gas discharge lamp s (Xenon lights)*:
Due to the high electr ical voltage, have the bulbs
replaced by a qualified technician . Head lights
with Xenon light are identified by the high volt­
age sticker.
A WARNING
Changing Xenon lamps without the necessary
equipment can cause serious personal injury.
- Bulbs are pressurized and can explode when
being changed . Potential risk of injury!
- On vehicles equipped with gas discharge
bu lbs (Xenon light) * life -threatening injuries
can result from improper handling of the
high -vo ltage portions of such lamps!
-On ly your authorized Audi dealer or quali­
fied workshop shou ld change the bulbs in
gas discharge lamps. There are parts with
sharp edges on the openings and on the
bulb holders that can cause serious cuts . If
you are uncertain about what to do, have
the wor k performed by an autho rized Audi
dealer or qualified workshop. Serious per­
sonal injury may result from improperly per­
formed work .
(D Tips
-If you st ill prefer to replace the light bulbs
yourself, be aware that the eng ine compart­
ment is a hazardous area to work
inq page 195 q &..
-It is best to ask your authorized Audi dealer
whenever you want to change a bulb.
239

M N
ci LL co
rl I.O
"' N
"' rl
When jump starting or charging the battery,
never connect the negative ground cable to
the battery negat ive post because the battery
manager system must be able to detect the
battery's state of charge. Always connect the
negative g round cab le to the negative ground
post of the battery manager control unit.
Use of jumper cables
Make sure to connect the jumper cable clamps in
exactly the order described below!
Fig. 197 Engine compa rtment: Connectors for jumper ca­
b les and c harger
Fig. 198 Jum p sta rting with the battery of anot her veh icle :
@ boos te r ba ttery, @ discharged veh icle battery
The procedure described below for connecting
jumper cables is intended to provide a jump start
for your vehicle.
Vehicle with discharged battery :
.. Turn
off lights and accessories, move lever of
automatic transmission to N (Ne utra l) or P
(Park) and set parking brake.
Connect POSITIVE(+) to POSITIVE(+) (red)
.. Remove the cover above the jump start connec­
t ion.
.. Open the cover on the posit ive pole ¢
fig. 197.
Emergency situations
1. Connect one end of the red positive cable on
the jump start bolt~
fig. 198 (D (Bolts un­
der cover= "positive") of the vehicle to be
started @.
2. Connect the other end to the positive termi- nal@of the booster battery @.
Connect NEGATIVE (-) to NEGATIVE(-)
(black)
3. Connect one end of the black negative cable
to the negative terminal ® of the booster
battery @.
4 . Connect the other end to the jump start bolt
@ (Bolts with hex head= "negative") of the
vehicle to be started @.
Starting the engine .. Start the engine of the veh icle with the booster
battery @. Run the eng ine at a moderate
speed .
.. Start engine with discharged vehicle battery @
in the usual manner.
.. If the engine fails to start: do not keep the
starter cranking for longer than 10 seconds.
Wait for about 30 seconds and then try again .
.. With engine running, remove jumper cables
from both vehicles in the exact
reverse order .
.. Close the cover on the positive pole.
The battery is vented to the outside to prevent
gases from entering the vehicle inter ior. Make
sure that the jumper clamps are well connected
with their
metal parts in full contact with the
batte ry terminals.
A WARNING
To avoid serious personal injury and damage
to the vehicle, heed all warnings and instruc­
tions of the jumper cable manufacturer. If in
doubt, call for road service.
- Jumper cables must be long enough so that
the vehicles do not touch .
- When connecting jumper cables, make sure
that they cannot get caug ht in any moving
parts in the eng ine compartment.
- Do not bend over the batteries -danger of
chemi cal burns!
241