ignition AUDI A5 CABRIOLET 2017 User Guide

a:,
a:,
.... N r--. N .... 0
0
LL 00
(memory level 2). The fuel pump nozzle iii
indicates the efficiency program*¢ page 24.
Single-trip memory (Trip computer 1)
The single-trip memo ry stores the trip informa ­
tion from the tim e the igni tion is turned on until
it is turned
off. If the tr ip is continued within 2
hours from the time the ignition was turned off,
the new data will be included in the calculation of
the current trip information.
If the trip is inter­
rupted for
more than 2 hours the memory is re­
set automat ically.
Total -trip memory (Trip computer 2)
Unlike the single-trip memory, the tota l-trip
memory is not reset automatically. This permits
you to evaluate your driving data for the entire
period between manual resets.
Efficiency program*
The efficiency program can help you to use less
fuel¢
page 24.
Operation
The trip computer is controlled by two switches
on the windshield wiper lever.
Fig. 11 Wind shield w iper leve r: controls fo r th e tr ip com­
p u ter
Operating
"'To display the trip computer memory levels,
press the
I RESE T! button @¢ fig. 11 repeated­
ly until the desired memory level is shown in
the display.
"' To display trip information within a memory
level, press the top or bottom part of the func­
t ion selection switch @.
Driver information system
The trip computer will not operate unless the ig­
nition is on. When you turn on the ignition, the
function that was in use when you last turned the
ignition off will be disp layed.
In addition to information about the trip comput­
er (trip computer 1, 2 and the efficiency pro­
gram*), information about other systems can al­
so be shown in the display. To sw itch the display
between the different information, tap the
I RESET ! button@ briefly .
Resetting values to zero
.,. Select a value in the desired trip computer or in
the efficiency program* .
"' Press and hold the
I RESET ! button@ for at
least one second . All values in the selected trip
computer or in the efficiency program* are re ­
set to zero .
If the data in tr ip computer 1 are deleted, then
the values in the efficiency program* will also be
reset .
With some vehicle eq uipment levels, the values
for the single trip or total trip memory can also
be reset in the Infotainment system
¢page 23.
(D Tips
All stored values will be lost if the vehicle bat­
tery is disconnected .
Basic Settings for the trip computer
Applies to: vehicles with trip computer
The radio or MM!* operating unit is used for set­
ting the trip computer 's basic settings.
.,. Select: Function button !CAR !> Instrument
cluster
> On-board computer 1 or On-board
computer
2 .
The values in the sing le-trip or the total-trip
memory can all be reset to zero at the same time
under
Reset i n the menu.
In addition, you can determine what information
from the trip computer should be shown in the
instrument cluster display . If one of the pieces of
driver information is turned
Off , that dr iver 1111>
23

messages appear automatically and are only dis­
p layed in the efficiency program. The fuel econo­
my messages turn off a utomat ically after acer ­
tain period of time.
.. To turn a fuel economy message off immedi ­
ately after it appears, press the I RESE T I button
¢ page 23, fig. 11 @, or
.. Press the function select ion switch ¢
page 23,
fig. 11
@ .
(D Tips
-Once you have turned a fuel economy mes­
sage off, it will on ly appear again after you
turn the ignit ion on again.
- The fuel economy messages are not dis­
played in every instance, but rather in inter­
vals over a period of t ime .
Service interval display
The service interval display reminds you when
your next service is due .
The schedule for the next oil change or inspec­
tion is calculated automatically and displayed ac ­
cord ingly . The display works in two stages :
Service rem inder
30 days before the next service is due, a service
reminder appears in the d isp lay when you turn on
the ignition.
After about 5 seconds the display switches back
to normal. The distance and time remain ing are
updated each time the ignition is turned on until
the date due for service is reached.
Se rvi ce due
When the due date for service is reached, the
m essage
Ser vice due! appears in the instrument
cluster immediately after you turn on the igni ­
tion . Additionally, a warning tone sounds. After
about 5 seconds the d isplay sw itches back to nor ­
mal.
Call ing up the servic e schedules
a:,
a:,
...... If or when an oil change or inspection is due, can N
~ be shown in the radio or MM!* d isplay by select-,.....
8 ing the serv ice interval d isplay in the car menu. LL 00
Dri ver informa tion system
Select I CAR I funct ion but ton > Se rvice i nterval
di spla y
or ICARI function button > Car systems *
control button > Ser vicing & checks.
Resetting the service int erval display
Yo ur autho rized Aud i dea le r will reset the co rre­
sponding serv ice schedu le after performing the
appropriate service on your vehicle . You also have
the possibility to reset the oi l change schedule
after having performed an oil change accord ing
to Audi specifications. SelectlCAR lfunction but­
ton
> Ser vice inter val display > Re set oil change
int erval
or ICARI function button > C ar systems *
control button > Se rvi cing & checks > Re set oil
change inter val.
(D Note
- Only reset the oil change display when you
have completed an o il change.
- If you disconnect the battery term inals, no
calcu lations can be made for the se rvice in­
terva l display dur ing th is time and no serv­
i c e rem inder will appear. Remembe r that
observ ing the proper serv ice i ntervals is vi­
t ally impo rtan t to ex tending the life o f your
vehicle, particular ly the engine, and ma in­
taining its va lue . Even if the mileage driven
is low, the maximum period o f one yea r
from one service to the next must not be ex­
ceeded.
(D Tips
The information in the Serv ice Reminder re­
mains stored even when the vehicle battery is
disconnected.
On Board Diagnostic
System (OBD)
Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) ¢4 in the
instrument cluster is part of the On-Board Diag­
nostic (OBD II) system .
The warning/indicator light ill uminates when the
ignition is sw itched on and goes out after the en­
gine starts and the idle has stab ilized . This indi-
cates that the MIL is working properly . ..,.
25

a:,
a:,
...... N r--. N ...... 0
0
LL 00
Opening and closing
Central locking
General description
The power locking system locks or unlocks all
doors and the rear lid simultaneously.
You can lock and unlock the vehicle centrally. You
have the following choices:
- Remote master key ¢
page 30,
-Door handles with convenience key*
O?page 30,
-Lock cylinder at the dr iver's door ¢ page 32,
or
- Power lock ing switch ins ide ¢
page 31.
Automatic lo cking
The automat ic locking feature locks all the vehi­
cle doors and the rear lid when you drive faster
than 9 mph ( 15 km/h) .
The car is unlocked again once the ignition key is
removed . In addition, the veh icle can be unlocked
if the opening function in the power locki ng sys ­
tem sw itch or at one of the door levers is actuat­
ed. The A uto Lock funct io n can be tu rned on and
off in the rad io or MM I*
¢ page 32.
Additionally, in the event of a crash with airbag
deployment the doors are automatically un­
l ocked to allow access to the veh icle.
Selective unlocking
When you lock the vehicle, the power locking sys­
tem will lock the doors and the rear lid . When
unlocking, yo u can set in the rad io or MMI*
whether
only the d river 's doo r o r the entire vehi­
cle shou ld be un loc ked
¢ page 32.
Anti-theft alarm w arning system
If the anti-theft alarm warning system detects a
break-in into the vehicle, acoust ic and visual
warn ing s ignals a re triggered.
The anti-theft warning system is activated auto­
mat ically when you lock the vehicle. It is deact i­
vated when unlocking using the remote key, with the mechanical key, and w hen you switch on the
i gnit io n.
Op ening and cl osing
The alarm also t urns off when the alarm cycle has
expi red.
Turn signals
When you unlock the veh icle, the turn s ignals
flash twice, when yo u lock it once. If they do not
flash, one of the doors, the l uggage compa rt­
ment lid or the hood is no t locked or the ignition
is still switched on.
Unintentionally locking yourself out
In the following cases there safeguards to p re­
ven t you locking your remo te mas te r key in the
vehicle:
- The vehicle does not loc k w ith the power lock­
ing sw itch
¢ page 31 if the d river 's doo r is
open.
- On veh icles with co nvenience key*, if the most
re cent ly used master key is in the l uggage com­
pa rtment, the rear lid is a utomatically unlocked
aga in after it is closed.
Do not lock your veh icle w ith the remote master
key or conven ience key* until all doors and the
rea r lid are closed . In this way yo u avoid loc king
yoursel f out acc identally .
A WARNING
=
-When you leave the vehicle, always remove
the ignition key and take it with you. This
will prevent passengers (children, fo r exam­
ple) from accidentally being locked in the
veh icle should they accidentally press the
power locking sw itch in the front doors.
- Do not leave children ins ide the vehicle un­
supervised . In an emergency it would be im­
possible to open the doors from the outside
without the key.
(D Tips
- In the event of a crash wit h airbag dep loy­
ment all locked doors will be automatically
unlocked to give access to the vehicle occ u­
pants from the o utside.
- If the power locking system sho uld mal­
function, you can lock the driver's door us­ ing the mechan ica l key ¢
page 32.
27

Opening and clo sin g
- If the power locking system should fail, you
can still open the fuel tank flap in an emer­
gency ¢
page 192.
-You are well advised not to keep val uables
inside an unatte nded vehicle, v is ible or not.
Even a properly locked vehicle cannot pro­
v ide the security of a safe.
- If the LED in the upper edge of the driver's
door panel comes on for about 30 seconds
after t he vehicle is locked, there is a mal­
funct ion in the power lock ing or the anti­
theft warning system . Have the malf unct io n
cor rected by an authorized Audi dealership
or q ualified repair facility.
Key set
F ig . 16 Key set
m 0 ±
~
@ Remote control key with mechanical key
You can centrally lock and unlock your veh icle
and start the engine w it h the master key with re­
mote cont rol. A mecha nical key is i nteg rated in
the master key¢
page 29.
@ Eme rgency key
The emergency key is not intended for constant
use . It shou ld only be used in an emergency, for
example, in place of the ign ition key
t:!:> page 72 . Ke ep it in a safe place and do not
car ry it on yo ur key r ing o r store it in the ve hicle.
Key replacement
If you lose a key, contact your author ized Audi
dealer immediately to have the
lost key disab led .
Be s ure to bring all your keys with you .
28
Number of keys
You can chec k the num ber of assigned keys to
your vehicle ¢
page 9. This allows you to make
sure yo u have received all of the keys when you
purchase a used vehicle .
Data in the master key
Dur ing driving, serv ice and maintenance-re levan t
da ta is cont inuous ly stored on your master key.
Your A udi service adviser can read out this data
and te ll yo u about the work your vehicle needs.
This applies also to veh icles with convenience
key *.
Personal comfort settings
If two people use one vehicle, it is recommended
that each person always uses "their own" maste r
k ey . W hen the ig nit ion is turned off or when the
vehicle is loc ked, personal conven ience settings
for the following systems are stored and as­
s igned to the remote master key.
- Climate control
- Power locking sy stem
- Sea t memory *
- Park ing system*
-Adapt ive cr uise control*
- Side assist*
- Drive se lect*
The stored settings are a utomat ica lly rec alled
when you unlock t he vehicle, when yo u ope n the
doo rs or when yo u turn on the ignition.
A WARNING
- Do not leave you r vehicle unattended with
the key in the ignition lock. Entry by una u­
thor ized persons could endanger you o r re­
sult i n theft o r damage the vehicle .
- Do not leave childre n unattended in the ve­
hicle, especially with access to vehicle keys .
Ungua rded access to the keys provides chil­
dren t he opport unity to start the engine
a nd /or ac tiva te ve hicl e sys tems s uch as the
power wi ndows etc. Unsu perv ised ope ration
of any vehicle system by children c an res ult
in ser ious injury.
.

a:,
a:,
...... N
" N ...... 0
0
LL co
-Do not remove the key from the ignition
lock until the vehicle has come to a com­
plete stop . Otherwise the steer ing column
lock could suddenly engage -causing the
risk of an accident .
(D Tips
-The operation of the remote control key can
be temporarily d isrupted by interference
from transmitters in the vicinity of the vehi­
cle work ing in the same frequency range
(e .g. a cell phone, radio equipment).
- For security reasons, replacement keys are
only available from authorized Aud i dea ler .
- For Declaration of Compliance to Un ited
States FCC and Industry Canada regulations
<::;> page 2 49.
Removing the mechanical key
Fig. 17 Remote master key: removing t he m ec hani ca l key
.,. Press the release button @o fig. 17.
.,. Pull the mechan ical key ® out of the master
key.
Using the mechan ical key, you can :
- lock and unlock* the glove compartment on the
passenger's side
c> page 63 .
-lock and unlock the vehicle manually
opage 32 if this should not be poss ible with
the master key.
- use the ignition key emergency release
opage 30.
Open ing and closing
Check light and battery in the master key
Fig. 18 Remote master key: re moving the bat tery holder
Check light in the master key
The check light@o fig. 18 in the master key
provides information about d ifferent conditions .
.,. The check light turns on briefly once when a
button is pressed, and during an "inquiry" by
the convenience key system.
.,. If the check light does not come on, the battery
is dead and has to be replaced . In addition,
when the battery is dead the
Ill indicator light
appears in the instr ument cluster display as
well as the message
Please change key bat­
tery .
Master key battery replacement
.,. Remove the mechanical key o page 29 .
.,. Press the re lease button ® o fig. 18on the bat­
t ery holder and at the same time pull the ba t­
tery holder out of the master key in the d irec ­
tion of the arrow .
.,. Insta ll the new battery CR 2032 with the"+"
sign facing down .
.,. Push the battery holder carefu lly into the mas­
ter key .
.,. Install the mechanical key.
@) For the sake of the environment
Dispose of dead batteries properly so as not
to pollute the environment.
@ Tips
The replacement battery must be the same
specificat ion as the original.
29

Opening and clo sin g
Emergency unlocking of the ignition key
In the event of malfunctions in the electrical sys­
tem, it may happen that you cannot remove the
ignition key.
.,. Remove the mechanical key c::;,poge 29.
.,. Lock the vehicle using the mechanical key
c::;, page 3 2.
.,. Have the electrical system inspected by an au­
thorized Aud i dea le rship.
Locking and unlocking the vehicle with the
remote control
F ig. 19 Remote mas ter key: function buttons
:8
"' 0 ±
"' OJ
.,. Press bu tton III to unlo ck the vehicle ¢ fig. 19.
.,. Press button 6:'.i to lock the vehicle c:;, .&. in Gen­
eral description on page 27 .
.,. Press button~ briefly to unlock the rear lid .
.,. Press the button
~ for at least one second to
open the rear lid .
.,. Push the red
I PANIC I button to activate the
panic function. The horn sounds and the turn
s ignals flash . Push the red
I PANIC I button again
to deactivate the pan ic fu nction .
If the vehicle is unlocked and no door, the rear lid
or the hood is opened w ith in 60 seconds, the ve­
h icle locks itse lf aga in automatica lly . This feature
prevents the veh icle from being accidentally left
un locked ove r a long period of time.
It depends o n the settings in the radio or MM!*
whether the entire veh icle is unlocked or only cer­
tain doo rs
c:;, page 32 .
On ve hicles with automatic transmission, these­
lector lever must be in the P pos ition, otherwise
the vehicle cannot be locked.
30
A WARNING
Read and fo llow all WARNINGS c:;, & in Gener­
al description on page 27.
(D Tips
- In order to make sure the locking function is
work ing, you should a lways keep your eye
on the vehicle to make sure it is properly
locked .
- Do not use the remote control if you are in­
side the car, otherwise you may uninten­
t ionally lock the vehicle, and then you would
set off the anti-theft a larm when you t ry to
sta rt the eng ine or open a door. I n case this
happens anyhow, push the un lock button@.
- Use the pan ic function on ly if you a re in an
emerge ncy sit uat io n.
- Additional remote cont rol key functions
c::;, page 35.
Locking and unlocking with convenience
key
App lies to : vehicles wi th conven ie nce key
The doors and the rear lid con be unlocked and
locked without operating the master key .
Fig. 20 Door hand le : locking th e veh icle
Unlocking vehicle
.,. Take hold of the door hand le . The door is un -
locked automatically.
.,. Pull the handle to open the door.
Locking vehicle
.,. Move the se lector lever to the P position, other ­
wise the vehicle cannot be locked .
.,. To lock the vehicle, close the door and touch
the sensor in the door handle
once c:;, fig. 20

a:,
a:,
...... N
" N ...... 0
0
LL co
Once the front passenger's door has been closed,
you cannot open it again from the outside. The
door can be opened from the inside by pulling
the door hand le.
A WARNING
Read and follow all WARNINGS¢&. in Gener­
al description on page 2
7 .
@ Tips
After the ignition is switched on, the power
locking system switch is enabled.
Electronic immobilizer
The immobilizer prevents your vehicle from being
started by unauthorized persons .
Inside the key there is a computer chip. This chip
automatically activates/deactivates the electron­ ic immobilizer.
Applies to vehicles with ignition lock:
The electronic immobilizer deact ivates automati­
cally when you insert the remote control key into
the ignition lock . It activates again automatically
when you remove the remote control key from
the ignition lock .
Applies to vehicles with convenience key:
If the remote control key is located inside the ve­
hicle and you press the
I START ENGINE STOPI
button , the electronic immobilizer deactivates
automatically. If you switch the ignition off and remove the remote control key from the vehicle,
the electronic immobilizer activates again auto­
matically .
A WARNING
Always take the key with you when you leave
the vehicle. The key can disarm the electronic
eng ine immobi lizer and permit an unauthor­
ized person to start the engine and enable op­
erat ion of the vehicle systems such as power
window or power sunroof leading to serious
personal injury.
Open ing and closing
(D Tips
-The vehicle cannot be started if an unau­
thorized key is used. The vehicle may not
start if another radio device such as a key
for another veh icle or a transponder is lo­
cated on the key ring.
- For Declaration of Compliance to United
States FCC and Industry Canada regulations
¢ page 249.
Luggage compartment
Lid
Opening /closing rear lid
Fig. 24 Rear lid: handle
Opening the rear lid
.. Press the button ~ on the remote control
master key for at least one second . The rear lid
unlocks and opens slightly. Or
.. Press the handle on the rear lid ¢
fig. 24.
Closing the rear lid
.. Pull the rear lid down at the gr ip on the inside
and allow it to drop gently to close it
Q &_.
A WARNING
-After closing the rear lid, always pull up on
it to make sure that it is properly closed.
Otherwise it could open suddenly when the
veh icle is moving.
- To help prevent po isonous exhaust gas from
being drawn into the vehicle, always keep
the rear lid closed while driving . Never
transport objects larger than those which fit
comp letely into the lu ggage area, because
then the rear lid cannot be fully closed. .,._
33

a:,
a:,
...... N
" N ...... 0
0
LL co
Power windows
Controls
The driver can control all power windows.
Fig. 27 Section of the driver's door: Controls
l
l
f
I
I !
I
Fig. 28 Center console : central power window switch
All power window switches ¢ fig. 2 7 are provided
with a
two-position function:
Opening the windows
"'Press the switch to the first stop and hold it un­
til the window reaches the desired position.
"' Press the switch briefly to the
second stop to
automatically open the window.
Closing the windows
"' Pull the switch to the first stop and hold it until
the window reaches the desired position.
"' Pull the switch briefly to the
second stop to au-
tomatically close the window.
Power window switches
@ Driver's door
@ Passenger 's door
© Left rear window
@ Right rear window
Opening and closing
You can open or close all the windows with the
switch ¢
fig. 28.
.&_ WARNING
-
-When you leave your vehicle -even if only
briefly - always remove the ignition key. This
applies particularly when children remain in
the vehicle. Otherwise the children could start the engine or operate electrical equip­
ment (e.g. power windows). The power win­
dows are functional until the driver's door or
passenger's door has been opened.
- Pay close attention when closing the win­
dows to prevent pinching of hands or limbs.
- When locking the vehicle from outside, the
vehicle must be unoccupied since the win­
dows can no longer be opened in an emer­
gency.
(D Tips
- When you open the doors, the windows au­
tomatically lower about 10 mm.
- After the ignition has been switched off, the
windows can still be opened or closed for
about 10 minutes. The window regulators
are not switched until the driver's or pas­
senger's door is opened.
Convenience opening/closing
The windows can be opened and closed with the
mechanical key or the emergency key.
Fig. 29 Key turns for opening and closing
Convenience opening feature
"'Use the emergency key or pull the mechanical
key o ut of the master key¢
page 29.
.,. Insert the key into the lock of the driver's door . ..,_
35

Opening and clo sin g
- De pen ding on the model of the system, you
may need to release the button on the re­
mote control d uring programm ing and
press it aga in. Hold each position you try for
at least 15 seconds before trying another position. Keep the turn sig nals on your vehi­
cle in view when doing t his.
- After programming the garage door ope ner,
i t may be necessary to synchronize the mo­
tor w ith the system. Refer to the ma nufac­
turer's i nstr uctions.
Programming the buttons (version
B)
Applies to: vehicles with garage door opener (Homelink}
F ig . 33 Distance between t he rad iato r g rille and t he hand
transm itter
Programming the button : Part 1 with the
control s
1. Switch the ignition on .
2. Press a nd ho ld both outer buttons in the roof
headliner ¢
page 37, fig. 32 until the LED@
turns off completely (after about 20 sec­
onds). T his procedure clears t he standa rd co­
des that were set at the factory and does
not
need to be repeated again to program the
o ther bu ttons.
3. Br iefly press the b utton o n the roof headline r
that yo u wou ld like to program.
4. Wait until the LED@ begins to blink quickly .
Programming mode is active for 5 m inutes .
5. Move in front of your vehicle while holding
the original remote contro l for the system
that would like to program to a button in the
roof headliner.
38
Programming the button: Part 2 at the
radiator grille
6 . Hold the remote contro l up to the radiator
grille on your vehicle¢
fig. 33.
7. Press and hold the remote control unt il the
turn s ignals on your vehicle blink. This may
take up to 30 seconds .
8 . If the eme rgency flashers bli nk three times,
the p rogramm ing was s uccessful.
If the
eme rgency flashers only blink one time, the
S m inute time limit for the prog ramming h as
ended or the prog ramming was no t success ­
ful. Repeat the prog ramming from t he third
step, or try changing the distance to the radi­
ator grille.
9.
If the garage door or other system does not
open us ing the buttons in the roof headline r
even though the programm ing was success­
ful, the system may use a ro lling code in­
stead of a fixed code .
Rolling code program­
ming must be perfo rmed ¢ page 39 .
The other two buttons in the roof head liner can
be programmed according to the inst ruct ions
above . Begin wi th the third step.
Erasing button prog ramming
The prog rammed buttons cannot be erased ind i­
vidually . They must a ll be erased together . Re­
program the buttons if necessary .
.. Switch the ignit ion on.
.. Press and hold bot h outer buttons in the roof
head liner until the LED@ turns off complete ly
(after about 20 seco nds).
Reprogramm ing th e buttons
.. Switch the ignition on .
.. To reprogram an individ ua l button, p ress and
hold the button unt il the LED @ starts to flash
quickly (after about 10 seconds) . Release the
button immed iately . Programming mode is ac­
t ive for 5 m inutes .
.,. Con tinue with the fif th step.
@ Tips
- Prog ramming using the buttons in the roof
head liner is not poss ible with a ll Infota in­
me nt sys tems.
If t his is the ca se, pr og ra m

Power top
Power top
Automatic power top
General information
The power top opens and closes automatically.
The entire power top is stored in the power top
compartment. The power top may be opened or
closed at speeds up to
30 mph (50 km/h).
Under normal conditions, the power top is wind
and waterproof. In rare cases, small droplets of
water may form under extreme weather condi­
tions such as torrential or prolonged rain. That is
normal and no cause for concern.
Follow the care instructions to keep the roof
from leaking and to maintain its appearance over
time
¢ page 182, Care and cleaning . Also ob­
serve the following:
- Only open and store the power top when it is
clean and dry . Sharp dirt particles can cause
damage to the rear window and the power top.
If the power top is stored when damp, dents
can form. If left stored for a long period of
time, mildew and other damage can develop .
- Do not leave the power top open for several
weeks or the creases in it may become discol­
ored.
- Remove ice and snow before opening the power
top. Do not use any sharp edged objects to re ­
move ice and snow or the power top could be
scratched or damaged . The rear window may be
cleared with a standard ice scraper .
- Do not open the power top when temperatures
are below 32 °F
(0 °() . The fabric used in the
power top loses its elasticity when tempera-
tu res are below freezing.
40
Opening/closing the power top
Fig. 34 Cente r conso le : power top sw itch
.. Switch the ignition on .
.,. To open/close the power top, pull/press and
hold the,,:;,§$ button during the entire process .
Th-f!.-) indicator light turns on.
- when the power top opens/closes or
- if the power top did not open/close completely.
Th.,
14 indicator light in the instrument cluster
turns off when the power top is completely open/
closed.
The
II light will blink if the power top cannot be
opened/ closed
¢ page 42 .
,&, WARNING
- When operating the power top, make sure
the function is not affected by wind or other
factors and that it does not interfere with
other drivers.
- Never drive when the power top is not
locked correctly. The wind from driving
could cause the power top to open. This can result in injuries and damage to the vehicle.
- Make sure no one will be injured by the pow­
er top supports and other moving parts
when opening and closing the top.
- The head space in the rear is reduced when
the power top opens and closes. Make sure
the passengers in the rear are far enough
away from the power top to reduce the risk
of injury .
- When operating the power top, visibility to
the rear is limited. Avoid operating the top
while driving in reverse.