spare wheel AUDI A5 COUPE 2013 User Guide

254 What do I do now?
-To help prevent the vehicle from moving
sudden ly and possibly slipping off the
jack, always fully set the parking brake
and block the wheel diagonally opposite
the wheel being changed with the fold­ ing chocks or other objects. When one
front whee l is lifted off the gro und, plac ­
ing the A utomat ic Transm iss io n in "P"
(Park) will
not prevent the vehi cle from
moving .
- Be fore yo u change a wheel, be sure the
ground is leve l and fi rm . If necessa ry,
use a sturdy board under the jack.
- After installing the spare tire, make sure
that you replace the f lat ti re/wheel in its
storage area properly and tighten the
knurled retain ing screw secu rely .
@ Note
If you are chang ing the wheel on a steep
incline, use a rock or similar object to
block the opposite wheel to prevent the
veh icle from mov ing.
(D} Tips
Obey a ll laws .
Changing a wheel
When you change a wheel, follow the se­
quence described below step -by -step and in
exactly that order.
1. Remove the decorative wheel c ove r* or
the wheel bolt cap s*. For more de tails see
a lso
¢ page 255, Decorative wheel cov ­
ers
or ¢ page 255, Wheels with wheel
bolt caps.
2 . Loosen the wheel bolts ¢ page 255.
3. Locate the proper mount ing point for the
jack and align the jack below that point
¢ page 256.
4. Lift the car with the jack¢ page 256 .
S. Remove the wheel with th e flat tire and
then install the spare tire
¢page 257.
6. Tighten all wheel bo lts ligh tly.
7 . lowe r the ve hicle w ith the jack . 8
. Use the wheel bolt w rench and firmly
tighten all wheel bolts in a crisscross pat­
te rn
¢ page 255.
9. Replace the decorati ve wheel cover * or
the wheel bolt caps *.
A WARNING
Always read and fo llow all WARNINGS and
in fo rmat ion¢ .&.
in Raising the vehicle on
page 256
and ¢ page 258.
After changing a wheel
A wheel change is not complete without the
doing the following .
.,. Always store the vehicle tool kit, the jack*,
and the replaced tire in the luggage com­
partme nt
¢ page 130.
.,. Check the tire pressure of the spare tire as
soon as possible.
.,. As soon as poss ib le, have the tightening
torque s on all whee l bolts chec ked w ith a
to rque wrenc h. The co rrect tighte ning tor ­
que is
90 ft lbs. (120 Nm) .
.,. Have the flat tire replaced as soon as possi­
ble.
@ Tips
- If you notice that the wheel bo lts a re
co rroded and difficult to turn while
chang ing a tire, they shou ld be rep laced
before you check the tightening torque.
- Dr ive at reduced speed until you have the
tightening torques checked.

-Do not raise the vehicle until yo u are
sure the jack is securely engaged.
- Passenge rs must not remai n in the
ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct, ad­
just as necessary and then contin ue to
ra ise the jack.
CD Note
Do not lift the vehicle by the si ll. Position
the vehicle jack only at the designated lift­
ing points on the sill. Otherwise, your vehi­
cle will be damaged.
Taking the wheel off /installing the spare
tire
Follow these instructions step-by-step for
changing the wheel.
Fi g. 189 Changing a wheel: using the screwdrive r han ­
dle (with the blade removed) to turn the bolts
Fig . 1 90 Changing a wheel: alignm en t pin ins ide t he
top hole
After you have loosened a ll wheel bolts and
ra ised the veh icle off the ground, remove and
replace the wheel as follows:
What do I d o now ? 257
Removing the wheel
.,. Remove the topmost whee l bolt completely
with the
he xagonal so ck et in the screwdriv ­
er handle (vehicle tool kit)
o fig. 189 and
set it aside on a
clean surface .
.,. Screw the threaded end of the
alignment
pin from the tool kit hand-t ight into the
empty bolt hole
o fig. 190.
.,. Then remove the other wheel bolts as de ­
scribed above .
.,. Take
off the whee l leav ing the a lignment
pi n in the bolt hole
o(D .
Putting on the inflat able spar e tire
.,. Push the spare tire over the alignment p in.
.,. Screw on the wheel bo lts and tighten them
slightly us ing the hexagonal socket .
• Remove the a lignment pin and inse rt and
tighten the rema ining wheel bolt slightly
like the res t.
.,. Turn the jack hand le co unter -clockwise to
lower the veh icle until the jack is fully re ­
leased .
.,. Use the wheel bolt wrench to tighten all
wheel bo lts f irm ly
o page 255 . Tighten
them
in a crisscross pattern, from one bolt
to the (approximately) opposite one, to keep
the wheel centered .
• Perfo rm the steps required afte r changing
the wheel
o page 254, After changing a
wheel.
T he hexagonal socket makes it easie r to re­
move th e wheel bo lts from the rim. Care
sho uld be taken when remov ing the reversib le
blade .
CD Note
When removi ng or insta lling the whee l,
the r im cou ld hit the bra ke roto r and dam­
age the roto r. Work carefu lly and have a
second person to help you .
(l} Tips
-When mount ing tires w ith unidir ectional
tread de sign
make sure the tread pat ­
tern is pointed the right way
o page258. II>-

258 What do I do now?
-The w heel bolt s should be clea n and easy
to tu rn. Check for dirt and corrosion on
t h e mat ing s urfaces o f both the whee l
and the h ub. Remove a ll dirt from these
su rfaces befor e remo unt ing the wheel.
- Do no t use the hexagona l socket in the
screwdriver handle to l oosen o r ti gh ten
t h e wheel bo lts .
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction .
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a spare tire w it h a t read patte rn
in te nded for use in a specific direction, p lease
n ote t he follow ing:
- The direction of rotation is marked by an
ar­
row on the side of the tire .
-If the spare t ire has to be installed in the in­
correct d irection, use the spare tire only
temporarily si nce the t ire will not be able to
achieve its optimum perfo rma nce character ­
ist ics w ith r ega rd to aquaplani ng, noise and
wea r.
- We recommend tha t you pay particular at ­
tent io n to this fact du ring wet weathe r and
t h at you a djust your spee d to matc h roa d
condition s.
- Re place the fla t tire w ith a n ew on e and
h av e it installed o n your ve hicle as soon as
p ossib le to res tore the ha nd ling ad vantages
o f a un idirect ional t ire.
Notes on wheel changing
Please rea d the information c::> page 242, New
tires and replacing tires and wheels
if you are
go ing t o use a spare t ire which is different
from the tires on your ve hicle.
Afte r you change a tire :
-Check the tire pressure on the spare imme­
diately after installation. -
Have the wheel bolt tightening torque
checked with a torque wrench as soon as
possible by your authorized Audi dealer or
a qualified workshop.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of
90 ft lbs. (120 Nm).
- If you notice that the wheel bolts are cor ·
roded and difficult to turn while chang ing
a tire , they should be replaced before you
check the tightening torque .
- Replace the flat tire w ith a new one and
have it installed on your vehicle as soon as
possible. Remount the wheel cover.
Until then, drive with extra care and at re·
duced speeds.
A WARNING ..__ -
- If you are going to equ ip your ve hicle
wit h tir es o r rims which differ from th ose
which w ere fac tory i nstalled, then be
s ure to read the information
c::> pag e 242 ,
N ew t ires and repl acin g tires and
wheels.
- Always make sure the dam age d wheel o r
eve n a flat tire and t he jack and to ol kit
a re p roperly secu red in the lugg age com­
p art ment and are no t loose in the pas ­
sen ger compartment.
- In an a cci dent or sudde n maneuver they
co uld fly forwa rd, in juring a nyone in the
veh icle.
- Always s to re damage d whee l, jack an d
too ls sec urely in the l ugga ge com pa rt­
ment. Othe rwise, in a n accide nt or s ud­
den maneuver they co uld f ly forwa rd,
causing inj ury to passe ngers in the ve hi­
cle .
(I) Note
Do not use comme rcially ava ilab le tire
sea lants. Ot herwise , th e e lectr ica l comp o­
nents of the tire pressu re monitoring sys­
tem* w ill no longe r work pr oper ly and th e
se nso r fo r th e tire pressure moni tor ing
syst em* will have to be repla ced by a
qu alifie d w ork s hop .

288 Index
Side assist Activating and deactivating . . . . . . . . . . 107
C leaning sensors .................. 202
Description .............. .. .. .... . 105
Side curtain airbags .......... .. .... . 162
Description ............... ... .... . 162
How they work ............ ... .... . 164
Safety instructions ................. 164
Side marker lights ......... .. .. .... .. 43
Ski sack ... .. .. . .......... .. .. .... .. 65
Snow chains ............... ... .... . 247
Sound system display . . . . . . . . . . . . . . . . . 24
Sources of information about child re-
straints and their use . . . . . . . . . . . . . . . . 184
Spare tire .... ................ ..... . 252
Speedometer . . . . . . . . . . . . . . . . . . . . . . . 12
Speed rating letter code ..... .. .. .. .. . 243
Speed warn ing system ...... .. .. .. .. . . 78
Sport different ial ........... ... .. .. . 109
Indicator lamp . . . . . . . . . . . . . . . . . . . . . 22
START ENGINE STOP button (convenience
key) .. .. .. ... ............ .. .. .. .. .. 75
START ENGINE STOP button (Convenience
key) . ... .... ................ ..... .. 74
Starting from rest . . . . . . . . . . . . . . . . . . . . 77
Starting off with a trai ler .... .. .. .... .. 78
Starting the eng ine . . . . . . . . . . . . . . 71, 74
Steering Locking the steer ing . . . . . . . . . . . . . . . . 71
also refer to Electro-mechanical power
assist ... ... ............ .. .. .. .. . 189
Steering wheel Adjusting steering column ... .. .. .. . . 71
Indicator light . . . . . . . . . . . . . . . . 18, 189
Steps for determining correct load limit . 240
Stopping the engine . . . . . . . . . . . . . . 73, 75
Storage ... .. ............... .. .... .. 59
Storage compartments . . . . . . . . . . . 60, 66
S tronic . .. .. ................ ... .. .. 88
S tronic transmission Driving information . . . . . . . . . . . . . . . . . 90
Emergency program .. .... .. .. .. .. . . 93
Emergency release . . . . . . . . . . . . . . . . . . 94
H ill descent control ........ ..... .. .. 91
Kick-down . . . . . . . . . . . . . . . . . . . . . . . . . 92
L aunch Control Program ... .. .. .... .. 93 Selector
lever lock . . . . . . . . . . . . . . . . . . 89
Se lector lever position . . . . . . . . . . . . . . . 88
t iptron ic . ... .. .. .. .............. .. 92
Sunroof .. .. .. .. .. ............. .. .. . 41
also refer to Panoramic tilting sunroof . 41
Sun shades Emergency closing (roof) ........... .. 42
Rear window ... .. ... .......... .. .. . 48
Sun visors .. .. .. .. ............. .. .. . 48
Symbols
refer to Warning/indicator lights ...... 13
T
Tac hometer . . . . . . . . . . . . . . . . . . . . . . . . . 11
Technical modifications .............. 276
Tether anchors .... ............. .... 182
T ether strap . . . . . . . . . . . . . . . . . . . . . . . 182
The first 1,000 miles (1,500 km) and after-
wards .. .. .. .. .. .. ... .... ...... .... 193
Tie-downs . . . . . . . . . . . . . . . . . . . . . 64, 131
tiptronic ... .. .. .. .... ...... ... .. .. . 82
Automatic Shift Lock (ASL) . . . . . . . . . . . 85
Driving ..... .. .. ... .......... .... . 82
Dynamic shift program ............. . 86
Emergency mode .............. ..... 87
Kick-down . . . . . . . . . . . . . . . . . . . . . . . . . 85
Manual shift program .......... .... . 86
Selector lever . . . . . . . . . . . . . . . . . . . . . . 84
S tronic transmission ... ..... ... .. .. . 92
Tire pressure . ..... ................ . 23 7
Tire pressure monitoring system
Loss of air pressure .. .......... .. .. 250
Malfunction . .. .. ............. .. .. 250
Resetting tire pressures ............. 251
Tires ........ ... .. .. ............... 231
Low aspect ratio tires . . . . . . . . . . . . . . . 248
Serv ice life .. .. .. ... .......... .... 241
Speed rating letter code ........ .. .. 243
T ire manufacturing date ............ 243
Tire pressure monitoring system ..... 249
Tire specifications ................ . 243
Tread depth ..... ............. .... 241
Uniform tire quality grading ..... .... 245
Win ter tires ... .. ............. .. .. 246
Tires and vehicle load limits ......... .. 239