four wheel drive AUDI A5 COUPE 2015 Owners Manual

Emergency braking
In the event that the conventional brake system
fails or locks.
11-In an emergency, pull the switch@¢ page 77,
fig. 81 and continue to pull it to slow your vehi­
cle down with the parking brake .
11-As soon as you release the switch @ or acceler-
ate, the braking process stops.
If you pull the sw itch @and ho ld it above a
speed of about
5 mph (8 km/h), the emergency
brak ing funct ion is initiated. The vehicle is braked
at all four wheels by activa ting the hydraulic
b rake system . The brake performance is similar
to making an eme rgency stop ¢
.&..
In o rder not to activate the emergency brak ing by
mista ke, an audible warning tone (b uzzer)
sounds when the sw itch @ is pulled . As soon as
the switch @ is released, or the accelerator pedal
is depressed, emergency braking stops .
A WARNING
Emergency braking should only be used in an
emergency, when the normal foot brake has
fai led or the brake pedal is obstructed. Using
the parking brake to perform emergency brak­
ing w ill slow your vehicle down as if you had
made a full brake a pplicat io n. The laws of
physics cannot be suspended even with ESC
and its associa ted components (A BS, ASR,
ED S). In cor ners and w hen ro ad or weather
condi tions a re bad, a full brake app lication
can ca use the vehicle to skid or the rear end to
break away - risking an accident .
Speed warning system
Overview
The speed warning system helps you to keep your
driving speed below a set speed limit.
T he speed warning system warns if the driver ex­
ceeds a previously stored maximum speed . A
~ war ning tone w ill sound as soon as the vehicle
~ speed exceeds the set speed by about 3 mph
~ (3 km/ h). At the same t ime, a warn ing symbol 1.1'1
N 1.1'1 ,....,
Dri ving
appea rs in the display. The symbol 's appea rance
mig ht be different in some models .
T he speed warn ing system h as two warning
t hr eshol ds that function i ndependen tly o f ea ch
othe r and t hat have somewhat d iffe rent p urpos ­
es :
Speed warning 1
You can use speed warning 1 to set t he maximum
speed w hile you are driv ing. This se tt ing will re­
mai n in effec t unti l yo u turn off the ig nition, as­
s u ming tha t you have not changed or reset the
setting .
T he . (USA models) /. (Can ada models)
speed wa rning symbo l in the warn ing
1 d isp lay
appears when you exceed the maxim um speed. It
goes out when the speed falls be low the stored
maximum speed.
T he speed warn ing symbol will also go out if the
speed
exceeds the stored maximum speed by
more than about
25 mph (40 km/h) for at least
10 seconds. The stored maximum speed is delet ­
ed.
Speed wa rning 2
Stor ing warning 2 is recommended if yo u always
want to be reminded of a certain speed, for ex­
amp le when you are traveling in a country that
has a general max imum speed limit, or if yo u do
not want to exceed a specified speed for winter
t ir es .
T he . (USA models)
I. (Canada models)
speed warning 2 symbol appears in the display
when you exceed the stored speed lim it. Unlike
warning 1, it will not go out unt il the vehicle
speed drops below t he sto red speed l imit .
Setting speed warn ing 2 ¢
page 80 .
(D Tips
Even though yo ur vehicle is eq uipped w it h a
speed warning system, you should still watch
the speedometer to make sure yo u are not
drivi ng faste r than the speed lim it.
79

M N
0 l­oo
rl I.O
"' N
"' rl
In extreme cases, EDL a utomatica lly switches off
to help keep the brake on the braked whee l from
overheating. EDL w ill switch on again automati ­
cally when conditions have returned to normal.
Steering re commendat ion
The ESC helps to stabilize the ve hicle by chang ing
the steering torque.
I n vehicles with dynamic steeri ng*, ESC also
h e lps to stabilize the steering in critical s itua­
tions .
Electronic interaxle differential lock* /
sel ectiv e wheel torque control*
The electron ic in teraxle d iffe ren tial lock (front
wheel drive) or the selective wheel torq ue contro l
(all wheel drive) operates when driving through
curves. The front whee l on the ins ide of the cu rve
or both whee ls on the inside of the curve are
braked selectively as needed. Thi s allows more
precise driving in curves. The applicable system
may not activate when driving in wet or snowy
conditions .
_&, WARNING
- The ESC and its integrated systems cannot
overcome the laws of physics. This is espe­
ci al ly impo rtant on slippe ry or wet roads. If
the sys tems begin acting to stabilize your
Switching on/off
Smart Technology
veh icle, you shou ld immediately change
your speed to matc h the road and traffic
conditions. Do not let the increased safety
provided by these systems tempt you to
take risks . Do ing so will increase the risk of a
loss of vehicle control, collision and serious
personal injuries.
- Always adapt your speed to road, traffic and
weather conditions. The risk of losing con­
trol of the vehicle inc reases when dr iving
too fast, espec ially through curves and on
slippery or wet roads, and when dr iving too
close to vehicles up ahead . The ESC and its
integrated systems cannot a lways prevent
coll isions -there is sti ll a risk of accidents!
- Always accelerate with special care on even,
smooth su rfaces such as those that are wet
or covered with ice and snow. The drive
wheels can spin even with these assistance
systems that can not always help to reduce
the risk of loss of vehicle cont rol.
{!) Tips
-ABS and ASR only work correct ly when a ll
four wheels are equipped w ith ident ica l
tires. Different tire sizes can lead to a reduc­
tion in engine power.
- You may hear noises when the systems de­
scribed are working.
ESC turns on automatically when you start the engine.
Fig. 153 Version A: lowe r ce nter console,~ OFF button
The ESC is designed to function in levels. Depend­
i ng on the level that is selected, the stabilization
function o f the ESC is limited or switched off . The
F ig. 154 Versio n B: uppe r ce nter console,~ OFF button
amount of s tabilization control will differ de­
pend ing on the level.
a, N N N ,.: CX) m
171

Smart Technolog y
Clean off accumulated salt coating from
brake discs and pads w ith a few carefu l
brake applications .
- If you damage the front spoiler, or if you in­
stall a d ifferent spoiler, be sure the air flow
to the front brakes is not obstructed. Other­
wise the brake system could overheat reduc ­
ing the effectiveness of the entire brake sys­
tem.
- Failure of one brake c ircuit will impair the
braking capab ility result ing in an increased
stopp ing distance. Avoid driving the veh icle
and have it towed to the nearest autho rized
Audi dealer or qualified workshop.
- Never let the vehicle ro ll to a stop with the
engine shut off .
- If the brake booster is not work ing, the
brake pedal must be pressed considerably
harder to make up for the lack of booste r as­
sistance .
Electro-mechanical
power assist, dynamic
steering
The electro-mechanical power assist helps the
driver when steering.
Power steering adapts electronically based on
the vehicle speed .
Indicator lights and me ssages
• Stee ring defe cti ve! D o not dr ive vehicle!
If this indicator light tu rns on and stays on and
this message appears, the power steering may
have fai led .
Do
not contin ue driving. See yo ur authorized
Aud i dealer o r a qua lified repair facility for assis­
tance.
l ;r- ij Dynami c steering : S ys te m fault! You can
c on tinu e dr iving
If the indicator light turns on and the message
appears, the steer ing may be more difficult to
move or mo re sensitive than us ual. The steer ing
wheel may also be at an ang le when dr iv ing
straight.
174
Drive slowly to your authorized Audi dea ler or
qualified workshop to have the ma lf u nction cor­
rected.
' -r, ij Dynamic ste ering: i nitializing
If this driver message appears and the indicator
li ght is flashing on the i nstrume nt pane l, dynam­
i c steer ing* is being rein it ia lized . After sta rting
the engine, the steer ing whee l w ill move sligh tly.
Re-initialization might be necessary if the steer ­
ing whee l was moved hard to th e left and right
whi le the vehicle was not moving . The display
goe s out as soon as initiali zation is comp lete.
A WARNING
,-
H ave the dynamic steering* system malfunc-
tion repaired as soon as possible by an author ­
ized Audi dealer or qualified workshop - r isk
of accid ent!
@ Tips
- If the . or 'T fl indicator light only stays on
for a short time, you may cont inue driving.
- The dynamic steering* stab ility system s are
not availab le in the event of a system mal­
function .
- For add itional information on dynamic
steering*, refer to<=> page 102 .
Driving with your quattro
Applies to vehicles : wit h all -w hee l drive
With all-wheel drive , all four wheels are driven .
General information
With a ll-wheel drive, power is distrib uted to a ll
fo ur wheels . This happens automatica lly depend­
i ng on your driving style and the road conditions
at the t ime . See also <=> page 1 70 .
A center d ifferential distributes the driving power
variab ly to the front and rear ax le. It works to­
gether w ith select ive whee l torque control , which
activates when drivi ng throug h curves
¢ page 171 . W ith the sport diffe rential*, power
distribution to the rear wheels is var iable and can
be ad justed with d rive select ¢ page 102 .
1111-

M N
i? co ,...., \!) ..,.,
N ..,., ,....,
The all-wheel drive concept is designed for high
engine power . Your vehicle is exceptionally pow­
erful and has excellent driving character istics
both under normal driving conditions and on
snow and ice. Always read and follow safety pre­
cautions <=>
,&.
Winter tire s
When driving in the winter, your vehicle with all­
wheel drive has an advantage, even with regular
tires. In winter road conditions it may be advisa­
ble to mount w inter tires (or all-season tires) for
improved driveability and braking: these tires
must be mounted on
all four wheels. See also
<=> page 220, Winter tires.
Tire chains
Where tire chains are mandatory on certain
roads, this normally also applies to vehicles with
all-wheel drive <=>
page 220, Snow chains.
Replacing wheels/tires
Vehicles with all-wheel drive must a lways have
tires of the same size. Also avoid tires with differ­
ent tread depths. For details see page
<=>
page 212, New tires or wheels.
Off-Road driving?
Your Audi does not have enough ground clear­
ance to be used as an off-road vehicle. It is there­
fore best to avoid rough tracks and uneven ter­
rain as much as possible. Also refer to
<=>page 177.
A WARNING
Always adjust your driving to road and traffic
conditions. Do not let the extra safety afford­
ed by all-wheel drive tempt you into taking
extra risks.
- Although the all-wheel dr ive is very effec­
t ive, always remember that braking capacity
is limited by tire traction. You should there­
fore not drive at excessive speeds on icy or
slippery road surfaces.
- On wet road surfaces, be careful not to dr ive
too fast because the front wheels could be ­
gin to slide on top of the water (aquap lan­
ing). If this shou ld occur, you will have no
Smart Technology
warning from a sudden increase in engine
speed as with a front-wheel drive vehicle.
Always drive at speeds which are suited to the road conditions -risk of crash.
Energy management
Starting ability is optimized
Energy management controls the distribution of
electrical energy and thus optimizes the availa­
bility of electrical energy for starting the engine.
If a vehicle with a conventional energy system is
not driven for a long pe riod of time, the battery
is discharged by idling current consumers (e.g.
i mmobil izer). In certain circumstances it can re­
su lt in there being insufficient energy available to
start the engine.
Intelligent energy management in your vehicle
hand les the distribution of electrical energy.
Starting ability is markedly improved and the life
of the battery is extended.
Basically, energy management consists of
bat­
tery diagnosis , idling current management
and
dynamic energy management.
Battery diagnosis
Battery diagnosis continuously determines the
state of the battery . Sensors determine battery
vo lta ge, battery current and battery tempera­
tu re. This determines the current state of charge
and the power of the battery.
Idling current management
Idling current management reduces energy con­
sumption whi le the vehicle is standing. With the
ignition switched off, it contro ls the energy sup­
ply to the various electrical components. Data
from battery diagnosis is considered.
Depending on the battery's state of charge, indi­
vidual consumers are gradually turned off to pre­
vent excessive discharge of the battery and thus
maintain starting capability .
Dynamic energy management
While the vehicle is being driven, dynamic energy
management distr ibutes the energy generated ..,.
175

Wheels
Occupant loading and distri­
bution for veh icle normal load
for various designated seat ing
capacit ies
Refer to the tire inflation pressure
label
c:> page 215, fig . 171 for
the number of seating positions .
Refer to the table
c:> page 216 for
the number of people that corre­
spond to the vehicle normal load .
New tires or wheels
Audi recommends having all work
on tires or wheels performed by
an authorized Audi dealer or au­
thorized repair facility. These fa­
cilities have the proper knowledge
and are equipped with the re­
quired tools and replacement
parts .
.,.N ew tires do no t yet have the
optimum adhesion properties.
D rive carefu lly and at moderate
speeds fo r the first 350 miles
(500 km) with new tires.
.,. Use tires of the same construc­
tion, size (rolling circumference)
and as close to the same tread
pattern as possib le on all four
wheels.
.,. Do not replace tires individually.
At least replace both tires on the same axle at the same time .
212
.,.A udi recommends that yo u use
Aud i O rig ina l equipment tires . If
you would like to use different t ir es, please note that the ti res
may pe rform differently even if
they are the same size
c:> A -
.,. If you would li ke to equ ip your
vehicle with a tire/rim combina ­
t ion tha t is different from what
was installed at the facto ry, con­
sult with an authorized Audi
dea ler or authorized repair facili­
ty before making a purchase
¢ ,&. .
The spare tire* is different from
the regular tires installed on the
vehic le - for examp le, if winter
tires or wide t ires are insta lled -
then only use the spare tire* tem­
porarily in case of eme rgency and
drive carefully wh ile it is in use. It
s h o ul d be rep laced wi th a regular
tire as soon as poss ib le .
On
all wheel drive vehic les, all
four wheels must be equipped
with tires that are the same brand
and have the same construction
and tread pattern so that the
dr ive system is not damaged by
diffe rent tire speeds. For this rea­
son, in case of emergency, only
use a spa re tire* that is the same
circumference as the regular tires . .,.

Wheels
A WARNING
Wheel bolts that are tightened or repaired in­correctly can become loose and result in loss
of vehicle control , which increases the risk of
an accident. For the correct tightening specifi­
cation, refer to
c:> page 22 7, After changing a
wheel.
- Always keep the wheel bolts and the threads
in the wheel hub clean and free of grease.
- Only use wheel bolts that fit the rim .
- Always have damaged rims repaired by an
authorized Audi dealer or authorized repair
facility. Never repair or disassemble rims
yourself, because this increases the risk of an accident.
Winter tires
Winter tires significantly improve the vehicle's handling when driving in winter conditions . Be­
cause of their construction (width, compound,
tread pattern), summer tires provide less traction
on ice and snow.
.., Use winter tires on all four wheels .
.., Only use winter tires that are approved for your
vehicle.
.., Please note that the maximum permitted
speed may be lower with winter tires
c:> .&,.
Your authorized Audi dealer or authorized re­
pai r facility can inform you about the maximum
permitted speed for your tires .
.., Check the tire pressure after installing wheels
c:> page 215.
The effectiveness of winter tires is reduced great­
ly when the tread is worn down to a depth of
0 .1S7 inch (4 mm). The characteristics of winter
tires also decrease greatly as the tire ages, re ­
gardless of the remaining tread.
A WARNING
-Never drive faster than the maximum per­
mitted speed for your t ires. This could cause
the tires to heat up too much . This increases
the risk of an accident because it can cause
the tire to burst.
220
- Always adapt your driving to the road and
traffic conditions. Drive carefully and reduce
your speed on icy or slippery roads. Even
winter tires can lose traction on black ice.
@ For the sake of the environment
Reinstall summer tires at the appropriate
time, because they provide better handling
when roads are free of snow and ice. Summer
tires cause less road noise, tire wear and fuel
consumpt ion.
(D Tips
You can also use all season tires instead of
winter tires. Please note that in some coun­
tries where winter tires are required, only win­
ter tires w ith the
& symbol may be permit­
ted.
· Snow chains
Snow chains improve traction in the snow .
.., Only install snow chains on the front wheels.
This applies also to vehicles with all wheel drive* .
.., Check and correct the seating of the snow
chains if necessary after driving a few feet. Fol­
low the instructions from the manufacturer .
.., Note the maximum permitted speed when driv­
ing with snow chains . Do not exceed 30 mph
(SO km/h) .
Snow chains not only improve the
driving in win­
ter road conditions, but also the
braking.
Use of snow chains is only permitted with certain
rim/tire combinations due to technical reasons.
Check with an authorized Audi dealer or author­
ized repair facility to see if you may use snow
chains .
Use
fine-mesh snow chains. They must not add
more than 0.53 inch (13.S mm) in height, includ­
ing the chain lock.
You must remove the chains when driving on
roads that are
free of snow. When roads are free
of snow, snow chains can impair handling and .,.

Wheels
Check/correct the pressures of all four tires and
store the pressure again in the Infotainment sys­
tem
c!) page 224.
mm (Tire Pressure Monitoring System) Tire pres­
sure: System malfunction!.
If m appears after
switching the ignition on or while driving and the
[I] i ndicator light in the instrument cluster
blinks for approximately one minute and then
stays on, there is system malfunction. Try to
store the correct tire pressures
c:> page 224 . If
the indicator light does turn off or turns on again
after a short period of time, drive to your author­
ized Audi dealer or qualified repair facility imme­
diately to have the malfunction corrected.
A WARNING
-If the tire pressure indicator appears in the
display, reduce your speed immediately and
avoid any hard steering or braking maneu­
vers. Stop as soon as possible and check the
tires and their pressure.
- The driver is responsible for maintaining the
correct tire pressure. You must check the
tire pressure regularly.
-Under certain conditions (such as a sporty
driving style, winter conditions or unpaved
roads), the tire pressure monitoring system
indicator may be delayed.
- Do not use run-flat tires on your vehicle. Us­
ing them when not permitted can lead to
vehicle damage or accidents.
(D Tips
- The tire pressure monitoring system can al­
so stop working when there is an ESC mal­
function.
- Using snow chains may result in a system
malfunction.
- The tires with the identification "AO" or
"RO"
c:> page 212 have been matched with
your Audi tire pressure monitoring system.
We recommend that you use these tires.
224
· Storing tire pressures
App lies to vehicles: wit h tire press ure mo nitor ing system
If the tire pressure changes or a tire is replaced,
it must be confirmed in the Infotainment sys­
tem .
.,. Make sure before storing that the tire pressures
of all four tires meet the spec ified values and
are adapted to the load
c!) page 215.
.,. Switch the ignition on.
.,. Select: the
I CARI function button > Tire pres­
sure monitoring
control button. Or
.,. Select: the
I CARI function button > Car Sys­
tems*
control button > Servicing & checks >
Tire pressure monitoring.
(D Tips
Do not store the tire pressures if snow chains
a re i nsta lied.